In this paper, a novel vibratory optical MEMS gyroscope is proposed, which is composed of an optical sensing system, an electro-static comb-drive actuator, and a mass-spring system with two degrees of freedom and a decoupling frame. The optical sensing system consists of a laser diode light source, a tunable Photonic Crystal (PC), a photo-detector, and integrated waveguides. The sensitive element of the proposed gyroscope has been designed with separated primary and secondary resonance frequencies to increase the operating bandwidth. Simulation results show that the functional characteristics of the proposed gyroscope are as follows: an operating frequency of 1830 Hz, a sense mode resonance frequency of 2330 Hz, an operating bandwidth of 200 Hz, a mechanical sensitivity of 0.14 nm=(°=s), an Optical sensitivity of 0.051 nm=(°=s), and a measurement range of ±500 °=s.
In this paper, we propose what we believe is a novel sensitive micro-optoelectromechanical systems (MOEMS) accelerometer based on intensity modulation by using a one-dimensional photonic crystal. The optical sensing system of the proposed structure includes an air-dielectric multilayer photonic bandgap material, a laser diode (LD) light source, a typical photodiode (1550 nm) and a set of integrated optical waveguides. The proposed sensor provides several advantages, such as a relatively wide measurement range, good linearity in the whole measurement range, integration capability, negligible cross-axis sensitivity, high reliability, and low air-damping coefficient, which results in a wider frequency bandwidth for a fixed resonance frequency. Simulation results show that the functional characteristics of the sensor are as follows: a mechanical sensitivity of 119.21 nm/g, a linear measurement range of and a resonance frequency of 1444 Hz. Thanks to the above-mentioned characteristics, the proposed MOEMS accelerometer is suitable for a wide spectrum of applications, ranging from consumer electronics to aerospace and inertial navigation.
In this paper, a novel highly sensitive differential optical MEMS accelerometer based on intensity modulation is proposed by using dual optical outputs and a two-dimensional (2D) photonic crystal power splitter. A TM-polarized light source, an optical power splitter (OPS) based on 2D photonic crystal (PhC), two typical photodiodes (PDs) and three optical ports build up the optical sensing system of the proposed sensor. The functional characteristics of the proposed device based on simulation results are as follows: Mechanical sensitivity of 0.0750 nm/g, linear measurement range of ±200 g, first mechanical resonance frequency of 17.7 kHz, optical sensitivity of 4.38 %/nm with bandwidth at half maximum (FWHM) of 1 nm (0.13 THz) at optical central wavelength of 1.495 μm (200.7 THz). This results in an optical quality factor of 1495 and total sensitivity of 0.3285 %/g. Due to the mentioned functional characteristics, the proposed sensor can be appealing for a wide range of applications, from inertial navigation and automotive to consumer electronics.
In this paper, we report a graphene-based plasmonic photodetector optimized using the particle swarm optimization (PSO) algorithm and compatible with complementary metal–oxide–semiconductor (CMOS) technology. The proposed photodetector structure is designed to minimize fabrication challenges and reduce production costs compared to more complex alternatives. Graphene has been used for its unique properties in the detection region, titanium nitride (TiN) as a CMOS-compatible metal, and both to aid in plasmonic excitation. Photodetectors have key parameters influenced by multiple independent variables. However, practical constraints prevent thorough adjustment of all variables to achieve optimal parameter values, often resulting in analysis based on several simplified models. Here we optimize these variables by presenting a new approach in the field of photodetectors using the capabilities of the PSO algorithm. As a result, for the proposed device at the wavelength of 1550 nm, the voltage responsivity is 210.6215 V/W, the current responsivity is 3.7213 A/W, the ultra-compressed length is less than 3 $$\mu {\text{m}}$$ , and the specific detectivity is 2.566× $${10}^{7}$$ Jones were obtained. Furthermore, the device in question works under the photothermoelectric effect (PTE) at zero bias and has zero dark current, which ultimately resulted in a very low noise equivalent power (NEP) of 4.5361 $${\text{pW}}/\sqrt{\text{Hz}}$$ .
22 October 2019 in IET Circuits, Devices & Systems
Here, a novel optical micro‐electro‐mechanical systems (MEMS) accelerometer sensor based on a micro‐ring resonator and an elliptical disk is proposed. The designed optical MEMS accelerometer is then analysed to obtain its functional characteristics. The proposed optical MEMS sensor presents an optical sensitivity of 0.0025 nm/g, a mechanical sensitivity of 1.56 nm/g, a linear measurement range of ±22 g, a first resonance frequency of 13.02 kHz, and a footprint of 34 μm × 50 μm. Furthermore, the achieved functional characteristics of the proposed accelerometer are compared to several recent contributions in the related field. According to this comparison study, the present optical MEMS accelerometer can be a suitable device for many applications ranging from consumer electronics to inertial measurement units.