Clinically, circle of Willis (CoW) is prone to anomaly and is also the predominant incidence site of intracranial aneurysms (IAs). This study aims to investigate the hemodynamic characteristics of CoW anomaly, and ascertain the mechanism of IAs initiation from the perspective of hemodynamics. Thus, the flow of IAs and pre-IAs were analyzed for one type of cerebral artery anomaly, that is, anterior cerebral artery A1 segment (ACA-A1) unilateral absence. Three patient geometrical models with IAs were selected from Emory University Open Source Data Center. IAs were virtually removed from the geometrical models to simulate the pre-IAs geometry. For calculation methods, a one-dimensional (1-D) solver and a three-dimensional (3-D) solver were combined to obtain the hemodynamic characteristics. The numerical simulation revealed that the average flow of Anterior Communicating Artery (ACoA) is almost zero when CoW is complete. In contrast, ACoA flow increases significantly in the case of ACA-A1 unilateral absence. For per-IAs geometry, the jet flow is found at the bifurcation between contralateral ACA-A1 and ACoA, which exhibits characteristics of high Wall Shear Stress (WSS) and high wall pressure in the impact region. It triggers the initiation of IAs from the perspective of hemodynamics. The vascular anomaly that leads to jet flow should be considered as a risk factor for IAs initiation.
To reduce the levelized cost of energy (LCOE) for offshore wind turbines, a novel wind–wave energy converter (WWEC) with a mass-adjustable buoy is designed. To analyze the impact of buoy mass variations on the system, a coupled comprehensive numerical model is established to simulate the aerodynamics of the turbine and the hydrodynamics of the platform and buoy. It is found that the occurrence of the buoy out of water significantly reduces the output power. Adjusting the buoy’s mass with suitable strategy can prevent the impact of slamming loads and improve the power output. The mass adjustment strategy is determined based on the output power of the wave energy converter under regular wave conditions. It is found that the mass adjustment strategy can significantly enhance the output power of combined system. The buoy does not move out of the water under the extreme conditions, which avoids the impact of slamming loads on system stability. Moreover, mass-adjustable buoys can reduce the risk of mooring line failure compare to a wind turbine without a buoy.
Considering the wear in mechanical bearings and the requirement for sensors or electrical power in active magnetic bearings, a novel nutation blood pump using a passive magnetic spherical bearing was developed in this paper. A mathematical model was derived to calculate the magnetic forces of the bearing between two pairs of magnetic sleeves in the nutation process. The calculation results demonstrate that the fluctuations of magnetic forces enlarge with the increase in the nutation angle; the magnetic forces obviously increase with the decrease in the air gap, especially along the z-axis. The dynamic magnetic finite element simulation was carried out to validate the mathematical model. The simulation and calculation results of the magnetic forces show consistent trends and provide a theoretical basis for the parameter design. To validate the performance of the pump, computational fluid dynamics (CFD) analyses and in vitro experiments were conducted. The predicted values of the flow velocity vector through the pump, and the wall shear stress, demonstrate that the pump has an antithrombotic property and would not cause serious blood damage. The hydraulic experiment shows that a pressure rise can be achieved in the range of 60–140 mmHg, at a rotational speed of 600–1600 rpm and a flow rate of 0.4–6.7 L/min. The normalized index of hemolysis (NIH) of the nutation pump was 0.0043 ± 0.0008 g/100L. The in vitro tests indicate the feasibility of a magnetically levitated ventricular-assist nutation blood pump for further suspension stability and animal trials.
Individual Pitch Control (IPC) is a crucial mechanism for mitigating asymmetric loads in offshore floating wind turbines (OFWTs). Conventional IPC systems face significant limitations in wind speed estimation accuracy and control strategy robustness, leading to load fluctuations and power degradation. To address these challenges, this study proposes a novel IPC system incorporating an innovative effective wind speed estimation method and a fuzzy PID control strategy. The wind speed estimation is achieved using polynomial fitting of the tip speed ratio and pitch angle. The fuzzy PID control strategy for IPC employs variable control gains calculated based on wind speed, azimuth angle, and blade root loads. To verify the performance of the proposed control system, it is compared against the baseline control system implemented in the OpenFAST software v1.0.0 by a case study of the NREL 5MW OFWT. Results demonstrate that the proposed system has high accuracy in wind speed estimation and maintains rated power output while reducing blade flapwise and pitching moments. Notably, the proposed EWSE has a 53.1% improvement in median error and a 19.23% improvement in data error threshold compared with a reference EWSE. Under strong turbulent conditions (15% turbulence intensity), the proposed system achieves a reduction of 17.9% in flapwise moment and 12.9% in pitching moment compared with a baseline controller.
A single stage cryogenic liquid turbine is designed for a large-scale internal compression air-separation unit to replace the Joule-Thompson valve and recover energy from the liquefied air during throttling process. It includes a 3-dimensional impeller, variable geometry nozzle, and asymmetrical volute. Strength evaluation of such a liquid turbine is both essential and complicated, which involves a proper evaluation of stress acting on the components and mechanical property of the chosen materials at low temperature. For metals under low temperatures, brittle fracture of the metal may occur prior to fatigue damage. A comprehensive consideration of low-temperature mechanical properties of materials and mechanical loads (due to hydrodynamic force and centrifugal force) acting on the components is of particular importance. Aluminum alloy 2031 is used for the turbine impeller and its mechanical properties under low temperatures are analyzed. To evaluate the stress acting on the components, numerical investigation using 3-D incompressible Navier-Stokes Equation together with k-epsilon turbulence model and mixing plane approach at rotator-stator interface are carried out at design and off-design flow with different nozzle-vane settings. The obtained pressure force is transformed into hydrodynamic load acting on the solid surface by means of fluid-solid interaction technology, and then used in the FEM (Finite Element Method) structure analysis together with the centrifugal force. Stress distribution of the component is obtained and deformation of the component analyzed. Evaluation of impeller strength is conducted for the cryogenic liquid turbine by combining the foregoing two aspects, and a use of alloy 2031 for the turbine expander is validated.