Drying is a thermodynamic process in which the moisture contained in the solid is removed by evaporation through the supply of an appreciable amount of thermal energy. It is recognized as a critical and intricate stage in the manufacturing process of ceramic materials. In general, drying at higher temperatures and lower air-relative humidity provokes severe hydric, thermal, and mechanical fractures in the ceramic parts, thus reducing product quality after the process. Then, this process must be realized under controlled conditions. From an industrial point of view, the drying process of sanitary ware takes place in two stages: drying at low temperatures (less than 40 °C) and drying at high temperatures (above 50 °C). Thus, the purpose of this work is to experimentally investigate the drying process at low temperatures in sanitary toilets. Drying experiments were conducted in an oven with the same temperature (35 °C) and different relative humidity of the drying air. The results of the moisture content, temperature, and dimension variations along the process, as well as drying and heating rates, are reported and analyzed. The results indicate that the higher the air’s relative humidity, the slower the moisture removal. Herein, aspects of the product quality after the drying process are also discussed.
Biocomposites are defined as eco-friendly materials from an environmental point of view. Because of the importance of this class of materials, their study is important, especially in moist and heated conditions. In this sense, this work aims to evaluate the transient behavior of moisture absorption and mechanical performance of biocomposites composed of a matrix of high-density biopolyethylene (originated from ethanol produced from sugarcane) filled with curauá vegetable fiber and organophilic montmorillonite clay. For this purpose, dry biocomposites filled with organophilic montmorillonite clay and curauá fiber (1, 3, and 5 wt.%) were prepared using a hand lay-up technique and subjected to moisture absorption and mechanical (flexural and impact tests) characterizations at different times. The experiments were carried out at water bath temperatures of 30 °C and 70 °C. The results have proven the strong influence of chemical composition and temperature on the moisture absorption behavior of biocomposites across time. For a higher percentage of reinforcement on the polymeric matrix, a higher moisture migration rate was verified, reaching a higher hygroscopic equilibrium condition at 16.9% for 5 wt.% of curauá fiber and 10.25% for 5 wt.% of montmorillonite clay particles. In contrast, the mechanical properties of all of the biocomposites were strongly reduced with an increasing moisture content, especially at higher fiber content and water bath temperature conditions. The innovative aspects of this research are related to the study of a new material and its transient mechanical behavior in dry and wet conditions.
The ceramics sector is crucial to the global economy. This research is devoted to studying the drying process of ceramic parts with arbitrary shapes based on Fick’s second law of diffusion and energy conservation. Herein, the mathematical procedure to obtain the exact solutions of the model equations using the Galerkin-based integral method is provided. In the mathematical modeling are considered constant properties and equilibrium conditions at the surface of the material. Emphasis is given to clay ceramic flat plate. Analytical results of the average moisture content, local temperature, and moisture content and temperature fields within the ceramic parts are presented, followed by an in-depth discussion.
31 July 2023 in Journal of Food Measurement and Characterization
Objetivou-se elaborar formulações de iogurte natural utilizando o amido extraído do caroço de abacate como ingrediente no processamento de alimentos. Foram elaboradas três formulações de iogurte contendo diferentes concentrações de amido do caroço (F1, F2, F3) sendo 0,5%, 0,7% e 1%, respectivamente. Estas formulações foram comparadas com a F0 e A1, formulação controle com 0% de amido, 1 % amido de milho respectivamente, em seguida realizou-se as análises físico-químicas e microbiológicas do do iogurte ao longo de 28 dias de armazenamento. O amido obtido apresentou teores altos de carboidratos, baixas concentrações de cinzas e lipídeos demostrando que ocorreu um bom isolamento do espessante, além de não apresentar contaminações microbiológica. Os iogurtes analisados estão em conformidade com a legislação vigente, tanto para os parâmetros físico-químicos como microbiológicos. Os resultados das análises microbiológicas para todas as formulações nos cinco períodos de tempo revelaram a ausência de presença de coliformes a 35ºC e 45ºC, fungos, leveduras e Salmonella. Além disso, as amostras demonstraram um nível adequado de sinérese.
17 September 2020 in Research, Society and Development
The concern for quality, nutritious, and safe food has increased in recent years and increasingly gaining ground in the food industries and research institutes around the world. In this context, cereal bars appear, which is a nutritious food of sweet and pleasant taste, source of vitamins, fiber, proteins, caloric source and complex carbohydrates. The fruits of the marizeiro (Geoffroea spinosa) by composition are considered good sources of proteins and sugars and low lipid content that generates energy value reduction, contributing to food formulations with caloric reduction. The aim of this research was to obtain mesocarp and almond meal from the fruit of the Marizeiro (Geoffroea spinosa), for the production of cereal bars determining their microbiological and physico-chemical profile in order to provide the product with an innovative character, different from what is found commercially. The flour produced was coded as almond flour (FA), mesocarpal flour (FM) and mixed flour (FMI). After processing, the flour was analyzed in terms of its physico-chemical and microbiological characteristics. All results of the microbiological analyses are in accordance with the standards established by the Technical Regulation of Resolution DRC n° 12. In the physical-chemical characterization all the contents are within the constant standards in the Brazilian legislation.