HAKAN CALISKAN

Dr. HAKAN CALISKAN

orcid

Research Focus & Metrics

Academic Career Length

15Years (2012-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
31 August 2018 in Journal of Manufacturing Science and Engineering
Verified
Journal Article
Closed access
PDF file
HCHAKAN CALISKAN
HAKAN CALISKAN
ZKZekai Murat Kilic
Zekai Murat Kilic
YAYusuf Altintas
Yusuf Altintas
Milling exhibits forced vibrations at tooth passing frequency and its harmonics, as well as chatter vibrations close to one of the natural modes. In addition, there are sidebands, which are spread at the multiples of tooth passing frequency above and below the chatter frequency, and make the robust chatter detection difficult. This paper presents a novel on-line chatter detection method by monitoring the vibration energy. Forced vibrations are removed from the measurements in discrete time domain using a Kalman filter. After removing all periodic components, the amplitude and frequency of chatter are searched in between the two consecutive tooth passing frequency harmonics using a nonlinear energy operator (NEO). When the energy of any chatter component grows relative to the energy of forced vibrations, the presence of chatter is detected. The proposed method works in discrete real time intervals, and can detect the chatter earlier than frequency domain-based methods, which rely on fast Fourier Transforms. The method has been experimentally validated in several milling tests using both microphone and accelerometer measurements, as well as using spindle speed and current signals.

1 September 2015 in Journal of Dynamic Systems, Measurement, and Control
Verified
Journal Article
Closed access
PDF file
HCHAKAN CALISKAN
HAKAN CALISKAN
TBTuna Balkan
Tuna Balkan
BPBülent E. Platin
Bülent E. Platin
This paper addresses the stability problem of pump controlled asymmetric hydraulic actuators and proposes a physical solution for it. The system under consideration utilizes a shuttle valve to compensate for unequal flow rates due to the asymmetry in the actuator. Possible hydraulic circuit configurations resulting from various valve positions are defined on the load pressure versus velocity plane and a generalized linear model of the system is derived. The investigation shows that there exists a critical load pressure region in which any equilibrium point requiring a partially open spool position is unstable during the retraction of the actuator. A particular valve underlap is proposed in order to avoid the instability and a shuttle valve selection guide is presented. Theoretical findings are validated by both numerical simulations and experimental tests. Results show that the undesired pressure oscillations are removed up to certain actuator velocities with the use of an underlapped shuttle valve.

1 October 2012 in Mechatronics
Verified
Journal Article
Closed access
EKErgin Kilic
Ergin Kilic
MDMelik Dolen
Melik Dolen
AKAhmet Bugra Koku
Ahmet Bugra Koku
HCHAKAN CALISKAN
HAKAN CALISKAN
TBTuna Balkan
Tuna Balkan

1 May 2014 in Control Engineering Practice
Verified
Journal Article
Closed access
EKErgin Kilic
Ergin Kilic
MDMelik Dolen
Melik Dolen
HCHAKAN CALISKAN
HAKAN CALISKAN
AKAhmet Bugra Koku
Ahmet Bugra Koku
TBTuna Balkan
Tuna Balkan

Verified
Journal Article
Open access
PDF file
HCHAKAN CALISKAN
HAKAN CALISKAN
This paper introduces a complete real-time algorithm, where the chatter is detected and eliminated by spindle speed manipulation via the chatter energy feedback calculated from the axis encoder measurement. The proposed method does not require profound knowledge of the machining dynamics; instead, the entire algorithm exploits the fact that milling vibrations consist of forced vibrations at spindle speed harmonics and chatter vibrations that are close to one of the natural modes, with sidebands which are spread at the multiples of spindle speed frequency above and below the chatter frequency. The developed algorithm is able to identify the amplitude, phase and frequency of all the harmonics constituting the periodic forced and chatter vibrations. The key challenge is to select dominant chatter frequencies for the calculation of a robust and accurate chatter energy ratio feedback; this is achieved by utilizing the frequency estimation variance of EKF as a novel chatter indicator. Based on the chatter energy ratio feedback, the controller overrides the spindle speed in order to suppress the chatter energy below a particular threshold value. The varying spindle speed challenge is handled by updating the state transition matrices of the Kalman filters and real-time calculation of the band-pass filter coefficients, based on the derived discrete time transfer functions. The developed algorithm is tested on a Deckel FP5cc CNC which is in-house retrofitted and has a PC-based controller for the real-time application of the proposed algorithm. It is shown that the real-time chatter frequency and amplitude estimates are compatible with off-line FFT analysis, and chatter can be successfully eliminated by energy feedback.