Piotr Dziarski

Dr. Piotr Dziarski


Research Focus & Metrics

Academic Career Length

7Years (2020-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
8 September 2021 in Materials
Verified
Journal Article
Open access
PDF file
NMNatalia Makuch
Natalia Makuch
PDPiotr Dziarski
Piotr Dziarski
Michal KulkaMichal Kulka
Michal Kulka
KMKEDDAM MOURAD
KEDDAM MOURAD
Plasma paste boriding was employed in order to produce the boride layers on Nimonic 80A-alloy. The process was carried out at temperatures of 1023 K, 1073 K and 1123 K for 3, 4 and 6 h in a gas mixture of 50% H2-50% Ar. Borax paste was used as a boron source. The microstructure of the produced surface layers consisted of the mixture of nickel borides and chromium borides. The effect of processing temperature and duration on the thickness of the borided layers was observed. The theoretical thicknesses of the borided layers were estimated using an integral diffusion model. A good correlation was obtained between the theoretical (modeled) and experimental depths of the plasma paste borided layers. The boride layers were characterized by a high hardness ranging from 1160 HV to 2132 HV. The multiphase character of the produced layers resulted in differences in hardness. A significant improvement of the wear resistance of the plasma paste borided Nimonic 80A-alloy was observed in comparison with the non-borided alloy.

26 August 2020 in Coatings
Verified
Journal Article
Open access
PDF file
DPDominika Panfil-Pryka
Dominika Panfil-Pryka
Michal KulkaMichal Kulka
Michal Kulka
NMNatalia Makuch
Natalia Makuch
JMJerzy Zbigniew Michalski
Jerzy Zbigniew Michalski
PDPiotr Dziarski
Piotr Dziarski
A gas-nitrided layer was produced on the toughened 42CrMo4 low-alloy steel using the changeable nitriding potential in order to limit the thickness of a brittle ε zone. The microstructure consisted of the compound ε + (ε + γ’) zone and diffusion zone (nitric sorbite with γ’ precipitates). Such a layer was subjected to laser heat treatment with or without remelting. The single laser tracks were formed using various laser beam powers (in the range of 0.234–0.624 kW) and scanning rates (in the range of 2.24–3.84 m·min−1) and the same laser beam diameter (2 mm). The microstructure of laser-modified nitrided layer usually consisted of re-melted zone (MZ) with coarse-grained nitric martensite Feα’ and possible ε precipitates, heat-affected zone (HAZ) with fine-grained nitric martensite Feα’ and γ’ precipitates and diffusion zone with nitric sorbite and γ’ precipitates. Sometimes, the compound zone was partially re-melted and an amount of iron nitrides remained in the MZ. Only one laser track was characterized by the different microstructure, consisting of the compound ε + (ε + γ’) zone, HAZ with fine-grained nitric martensite Feα’ and γ’ precipitates and diffusion zone with nitric sorbite and γ’ precipitates. This laser track was formed without visible effects of remelting. The effect of temperature distribution during laser heat treatment of gas-nitrided 42CrMo4 steel on the microstructure and mechanical properties was studied. The equations developed by Ashby and Esterling were used in order to determine the temperature distribution along the axis of each laser track. Taking into account the temperature profiles, it was possible to calculate the depths of MZ and HAZ. These predicted values were compared to those-measured based on the microstructure observations, obtaining good compatibility. The microstructure of the produced surface layers influenced the mechanical properties such as hardness and Young’s modulus. The hardness of MZ was higher than that of ε zone and lower than that of ε + γ’ zone when compared to nitrided layer. Whereas Young’s modulus of MZ was significantly higher than those characteristic of the compound zone in gas-nitrided layer (both ε and ε + γ’ zone) and similar to that of HAZ. The laser heat treatment (LHT) without remelting resulted in the similar hardness and slightly higher Young’s modulus of ε zone in comparison with the nitrided layer. Simultaneously, such a treatment of the nitrided layer did not influence the hardness and the Young’s modulus of ε + γ’ zone considerably. The hardness of HAZ was higher than that of MZ and that of the same area of diffusion zone in the nitrided layer because of the presence of fine-grained nitric martensite with γ’ precipitates after laser quenching.

29 October 2020 in Materials
Verified
Journal Article
Open access
PDF file
Michal KulkaMichal Kulka
Michal Kulka
DMDaria Mikołajczak
Daria Mikołajczak
NMNatalia Makuch
Natalia Makuch
PDPiotr Dziarski
Piotr Dziarski
Damian PrzestackiDamian Przestacki
Damian Przestacki
Andrzej MiklaszewskiAndrzej Miklaszewski
Andrzej Miklaszewski
Austenitic 316L steel is known for its good oxidation resistance and corrosion behavior. However, the poor wear protection is its substantial disadvantage. In this study, laser surface alloying with boron and some metallic elements was used in order to form the surface layers of improved wear behavior. The microstructure was studied using OM, SEM, XRD, and EDS techniques. The laser-alloyed layers consisted of the only re-melted zone (MZ). The hard ceramic phases (Fe2B, Cr2B, Ni2B, or Ni3B borides) occurred in a soft austenitic matrix. The relatively high overlapping (86%) resulted in a uniform thickness and homogeneous microstructure of the layers. All the laser-alloyed layers were free from defects, such as microcracks or gas pores, due to the use of relatively high dilution ratios (above 0.37). The heat-affected zone (HAZ) wasn’t visible in the microstructure because of the extended stability of austenite up to room temperature and no possibility to change this structure during fast cooling. The use of the mixtures of boron and selected metallic elements as the alloying materials caused the diminished laser beam power in order to obtain the layers of acceptable quality. The thickness of laser-alloyed layers (308–432 μm) was significantly higher than that produced using diffusion boriding techniques.

14 June 2020 in Coatings
Verified
Journal Article
Open access
PDF file
NMNatalia Makuch
Natalia Makuch
PDPiotr Dziarski
Piotr Dziarski
Michal KulkaMichal Kulka
Michal Kulka
The gas boriding process is an appropriate technique used for increasing the hardness and wear resistance of iron and steels. However, the boron halides (e.g., BCl3, BF3) are rarely used as a boron source during gas boriding in industry due to the toxic character of these reagents. The possibility of the use of organic compounds as a boron source in plasma assisted processes was the instigation to determine the possibility of applying these agents for gas boriding. In the present work trimethyl borate was used as an organic boron source. The use of a N2–H2–B(CH3O)3 atmosphere ensured the appropriate conditions for the simultaneous gas borocarburizing of Armco iron. The process was carried out at 1223 K (950 °C) for 2 h. The produced layer consisted of two zones: an outer zone containing a diffusion of boron atoms and an inner zone containing a diffusion of carbon atoms, under the outer zone. Due to the reduction of trimethyl borate with hydrogen, free atoms of carbon were released for the gas atmosphere. Therefore, there existed favorable conditions for carburizing. Unfortunately, the formation of a carburized layer was the reason for the difficult diffusion of boron atoms. As a consequence, the boron diffusion front was hindered, and the outer boride layer was relatively thin (ca. 7.8 µm). The boride layer contained only Fe2B phase, which was characterized by high hardness in the range from 1103 HV0.01 to 1546 HV0.01. The presence of iron borides in the outer layer was also the reason for increased wear resistance in comparison with untreated Armco iron.

8 November 2021 in Materials
Verified
Journal Article
Open access
PDF file
PDPiotr Dziarski
Piotr Dziarski
NMNatalia Makuch
Natalia Makuch
The study investigated the dependence of the indentation load on nanomechanical properties for a gas-borided layer produced on Inconel 600-alloy. During the measurements, the indentation load range from 10 mN to 500 mN was used. Three types of tested areas, differing in the concentration of chromium, were examined. The increase in chromium concentration was accompanied by an increase in indentation hardness and Young’s modulus. Simultaneously, the increase in the indentation load resulted in a decrease in the indentation hardness and Young’s modulus, for each type of the tested area. The presence of the indentation size effect was analyzed using four models: Meyer’s law, Hays and Kendall model, Li and Bradt model, Nix and Gao model. For all tested areas, good agreement with the Meyer’s law was obtained. However, areas with a higher chromium concentration were more susceptible to indentation size effect (ISE). The proportional specimen resistance (PSR) model was used to describe the plastic-elastic behavior of the tested materials, as well as to detect the presence of ISE. It was found that the increase in chromium concentration in the tested area was accompanied by a greater tendency to elastic deformation during nanoindentation.

31 May 2021 in Materials
Verified
Journal Article
Open access
PDF file
Michal KulkaMichal Kulka
Michal Kulka
DMDaria Mikołajczak
Daria Mikołajczak
PDPiotr Dziarski
Piotr Dziarski
DPDominika Panfil-Pryka
Dominika Panfil-Pryka
Austenitic 316L stainless steel is known for its good resistance to corrosion and oxidation. However, under conditions of appreciable mechanical wear, this steel had to demonstrate suitable wear protection. In this study, laser surface alloying with boron and some metallic elements was used in order to improve the hardness and wear behavior of this material. The microstructure was described in the previous paper in detail. The microhardness was measured using Vickers method. The “block-on-ring” technique was used in order to evaluate the wear resistance of laser-alloyed layers, whereas, the potentiodynamic method was applied to evaluate their corrosion behavior. The produced laser-alloyed layers consisted of hard ceramic phases (Fe2B, Cr2B, Ni2B or Ni3B borides) in a soft austenitic matrix. The significant increase in hardness and wear resistance was observed in the case of all the laser-alloyed layers in comparison to the untreated 316L steel. The predominant abrasive wear was accompanied by adhesive and oxidative wear evidenced by shallow grooves, adhesion craters and the presence of oxides. The corrosion resistance of laser-alloyed layers was not considerably diminished. The laser-alloyed layer with boron and nickel was the best in this regard, obtaining nearly the same corrosion behavior as the untreated 316L steel.