Dominika Panfil-Pryka

Mrs. Dominika Panfil-Pryka

Poznan University of Technology, Poland
orcid

Research Focus & Metrics

Academic Career Length

11Years (2016-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 June 2017 in Journal of Alloys and Compounds
Verified
Journal Article
Closed access
DPDominika Panfil-Pryka
Dominika Panfil-Pryka
Michal KulkaMichal Kulka
Michal Kulka
PWP. Wach
P. Wach
JMJ. Michalski
J. Michalski
Damian PrzestackiDamian Przestacki
Damian Przestacki

22 May 2017 in Transactions of the Indian Institute of Metals
Verified
Journal Article
Closed access
PDF file
KMKEDDAM MOURAD
KEDDAM MOURAD
RCR. Chegroune
R. Chegroune
Michal KulkaMichal Kulka
Michal Kulka
NMNatalia Makuch
Natalia Makuch
DPDominika Panfil-Pryka
Dominika Panfil-Pryka
STS. Taktak
S. Taktak

6 July 2016 in Transactions of the Indian Institute of Metals
Verified
Journal Article
Closed access
PDF file
KMKEDDAM MOURAD
KEDDAM MOURAD
RCR. Chegroune
R. Chegroune
Michal KulkaMichal Kulka
Michal Kulka
DPDominika Panfil-Pryka
Dominika Panfil-Pryka
SUS. Ulker
S. Ulker
STS. Taktak
S. Taktak

1 August 2016 in Optics & Laser Technology
Verified
Journal Article
Closed access
Michal KulkaMichal Kulka
Michal Kulka
DPDominika Panfil-Pryka
Dominika Panfil-Pryka
JMJerzy Zbigniew Michalski
Jerzy Zbigniew Michalski
PWP. Wach
P. Wach

26 August 2020 in Coatings
Verified
Journal Article
Open access
PDF file
DPDominika Panfil-Pryka
Dominika Panfil-Pryka
Michal KulkaMichal Kulka
Michal Kulka
NMNatalia Makuch
Natalia Makuch
JMJerzy Zbigniew Michalski
Jerzy Zbigniew Michalski
PDPiotr Dziarski
Piotr Dziarski
A gas-nitrided layer was produced on the toughened 42CrMo4 low-alloy steel using the changeable nitriding potential in order to limit the thickness of a brittle ε zone. The microstructure consisted of the compound ε + (ε + γ’) zone and diffusion zone (nitric sorbite with γ’ precipitates). Such a layer was subjected to laser heat treatment with or without remelting. The single laser tracks were formed using various laser beam powers (in the range of 0.234–0.624 kW) and scanning rates (in the range of 2.24–3.84 m·min−1) and the same laser beam diameter (2 mm). The microstructure of laser-modified nitrided layer usually consisted of re-melted zone (MZ) with coarse-grained nitric martensite Feα’ and possible ε precipitates, heat-affected zone (HAZ) with fine-grained nitric martensite Feα’ and γ’ precipitates and diffusion zone with nitric sorbite and γ’ precipitates. Sometimes, the compound zone was partially re-melted and an amount of iron nitrides remained in the MZ. Only one laser track was characterized by the different microstructure, consisting of the compound ε + (ε + γ’) zone, HAZ with fine-grained nitric martensite Feα’ and γ’ precipitates and diffusion zone with nitric sorbite and γ’ precipitates. This laser track was formed without visible effects of remelting. The effect of temperature distribution during laser heat treatment of gas-nitrided 42CrMo4 steel on the microstructure and mechanical properties was studied. The equations developed by Ashby and Esterling were used in order to determine the temperature distribution along the axis of each laser track. Taking into account the temperature profiles, it was possible to calculate the depths of MZ and HAZ. These predicted values were compared to those-measured based on the microstructure observations, obtaining good compatibility. The microstructure of the produced surface layers influenced the mechanical properties such as hardness and Young’s modulus. The hardness of MZ was higher than that of ε zone and lower than that of ε + γ’ zone when compared to nitrided layer. Whereas Young’s modulus of MZ was significantly higher than those characteristic of the compound zone in gas-nitrided layer (both ε and ε + γ’ zone) and similar to that of HAZ. The laser heat treatment (LHT) without remelting resulted in the similar hardness and slightly higher Young’s modulus of ε zone in comparison with the nitrided layer. Simultaneously, such a treatment of the nitrided layer did not influence the hardness and the Young’s modulus of ε + γ’ zone considerably. The hardness of HAZ was higher than that of MZ and that of the same area of diffusion zone in the nitrided layer because of the presence of fine-grained nitric martensite with γ’ precipitates after laser quenching.

29 October 2020 in Materials
Verified
Journal Article
Open access
PDF file
Michal KulkaMichal Kulka
Michal Kulka
DMDaria Mikołajczak
Daria Mikołajczak
NMNatalia Makuch
Natalia Makuch
PDPiotr Dziarski
Piotr Dziarski
Damian PrzestackiDamian Przestacki
Damian Przestacki
Andrzej MiklaszewskiAndrzej Miklaszewski
Andrzej Miklaszewski
Austenitic 316L steel is known for its good oxidation resistance and corrosion behavior. However, the poor wear protection is its substantial disadvantage. In this study, laser surface alloying with boron and some metallic elements was used in order to form the surface layers of improved wear behavior. The microstructure was studied using OM, SEM, XRD, and EDS techniques. The laser-alloyed layers consisted of the only re-melted zone (MZ). The hard ceramic phases (Fe2B, Cr2B, Ni2B, or Ni3B borides) occurred in a soft austenitic matrix. The relatively high overlapping (86%) resulted in a uniform thickness and homogeneous microstructure of the layers. All the laser-alloyed layers were free from defects, such as microcracks or gas pores, due to the use of relatively high dilution ratios (above 0.37). The heat-affected zone (HAZ) wasn’t visible in the microstructure because of the extended stability of austenite up to room temperature and no possibility to change this structure during fast cooling. The use of the mixtures of boron and selected metallic elements as the alloying materials caused the diminished laser beam power in order to obtain the layers of acceptable quality. The thickness of laser-alloyed layers (308–432 μm) was significantly higher than that produced using diffusion boriding techniques.