Myunghee Lee

Prof. Myunghee Lee

orcid

Research Focus & Metrics

Academic Career Length

10Years (2017-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 June 2020 in IEEE Transactions on Circuits and Systems I: Regular Papers
Verified
Journal Article
Closed access
WHWoojin Hong
Woojin Hong
MLMyunghee Lee
Myunghee Lee
The growth of IoT applications requires DC-DC converters to have small printed circuit board (PCB) areas and high efficiency over a wide load range. A multi-mode operation of DC-DC converters, therefore, is often necessary to achieve this high efficiency over a wide load range. This paper introduces a tri-mode DC-DC buck converter for IoT applications. The tri-mode operation with PWM, PFM, and multiple-sawtooth PWM (MSPWM) modes helps to retain the high efficiency over the wide load range. The MSPWM mode also enhances a noise margin of the converter, ensuring a regular switching operation at an ultra-light load condition. With a load current prediction scheme, the proposed tri-mode converter requires neither additional load current sensor nor multiple mode controllers. In addition, a soft-start operation is employed to prevent an in-rush current. The proposed tri-mode buck converter has been fabricated through a 0.18-μm CMOS process with a chip area of 0.97 mm x 0.88 mm. A load-dependent seamless mode transition is realized, and a maximum converter efficiency of 91% has been measured with a 7.4-MHz switching frequency.

10 March 2020 in IEEE Access
Verified
Journal Article
Open access
JSJewoo Seong
Jewoo Seong
JJJinwoong Jang
Jinwoong Jang
JLJaehoon Lee
Jaehoon Lee
MLMyunghee Lee
Myunghee Lee
Micro-displays based on micro-LEDs are becoming more and more attractive in AR/MR (Augmented/Mixed Reality) applications. A display size of 0.5 to 0.7-inch is preferred, with 5,000 PPI (Pixel Per Inch) or higher. Due to this pixel density and size, a CMOS (Complementary Metal-Oxide-Silicon) backplane is an ideal solution to drive these pixelized micro-LEDs. As the required pixel size gets smaller, the design of the appropriate pixel circuit becomes more challenging. The simplest 2T1C (2 transistors & 1 capacitor) pixel circuit has potential problems, due to the leakage current of the switch transistor and the voltage drop on the matrix array layout. In this paper, a pixel circuit is proposed as a solution to overcome these two issues. Our simulation results show that the variation of the driving current to the LED is improved by 95 %, and the IR drop error rate is around 2.2 % compared to the 2T1C circuit. The test results also show that the error rate of IPIXEL for the whole region of display is under 2.5 %. This work is verified using a test chip implementation with 180 nm CMOS process technology.

11 January 2021 in IEEE Journal of Solid-State Circuits
Verified
Journal Article
Closed access
WHWoojin Hong
Woojin Hong
MLMyunghee Lee
Myunghee Lee
In this article, a dual-ramp modulation scheme is proposed to solve an instability during the discontinuous conduction mode (DCM) operation of current-mode constant on-time (COT) controlled boost converters. A duty cycle-dependent auxiliary waveform, which is generated by the proposed capacitor-coupled common-drain amplifier (CCCDA), is summed with an inductor current information to form a current feedback loop. With the proposed scheme, the pulse frequency modulation (PFM) operation can be spontaneously accompanied by the current-mode COT control to enhance a light-load efficiency. In addition, a translinear loop (TLL)-based valley current sensor is introduced to sense a valley inductor current while solving the response time and stability problems of the previous SenseFET-based current sensor. An adaptive ON-time (AOT) generator provides a quasi-fixed switching frequency in the CCM operation regardless of the conversion ratio. The proposed boost converter has been fabricated using a 0.18- μm CMOS process with a total chip area of 1.23 mm × 1.37 mm. It achieves a peak efficiency of 94.5% even at a high-switching frequency of 10 MHz, and smooth mode transition between PFM and pulsewidth modulation (PWM) operations depending on the load conditions.

3 May 2018 in IEEE Transactions on Vehicular Technology
Verified
Journal Article
Closed access
SKSukhwan Kang
Sukhwan Kang
JSJewoo Seong
Jewoo Seong
MLMyunghee Lee
Myunghee Lee
Controller area network with flexible data rate (CANFD) has been introduced to support higher data rates for intelligent automotive systems. To achieve a robustness in the electronic functions of electronic systems, CAN-FD transmitters should provide a good symmetry between the differential signaling on the CAN bus radiating a low electromagnetic emission (EME). This paper proposes a new CAN-FD transmitter which achieves good symmetry on the CAN-FD signals. Also, a so-called “Ping-Pong” driving scheme is introduced. Without using complex circuits and after-calibration process, this method can match accurate turn ON/OFF timing of the transmitter signals. The proposed CAN-FD transmitter was fabricated using a 0.18 μm automotive Bipolar-CMOS-DMOS process. The measurement results show that the proposed CAN-FD transmitter improves the voltage symmetry of the CAN bus at 5 Mbps, achieving a low EME.

19 January 2018 in Sensors
Verified
Journal Article
Open access
PDF file
WSWonkuk Seo
Wonkuk Seo
JPJae-Eun Pi
Jae-Eun Pi
SCSung Haeung Cho
Sung Haeung Cho
SKSeung-Youl Kang
Seung-Youl Kang
SASeong-Deok Ahn
Seong-Deok Ahn
MLMyunghee Lee
Myunghee Lee
In this paper, we introduce a transparent fingerprint sensing system using a thin film transistor (TFT) sensor panel, based on a self-capacitive sensing scheme. An armorphousindium gallium zinc oxide (a-IGZO) TFT sensor array and associated custom Read-Out IC (ROIC) are implemented for the system. The sensor panel has a 200 × 200 pixel array and each pixel size is as small as 50 μm × 50 μm. The ROIC uses only eight analog front-end (AFE) amplifier stages along with a successive approximation analog-to-digital converter (SAR ADC). To get the fingerprint image data from the sensor array, the ROIC senses a capacitance, which is formed by a cover glass material between a human finger and an electrode of each pixel of the sensor array. Three methods are reviewed for estimating the self-capacitance. The measurement result demonstrates that the transparent fingerprint sensor system has an ability to differentiate a human finger’s ridges and valleys through the fingerprint sensor array.

25 April 2022 in IEEE Access
Verified
Journal Article
Open access
WJWungki Jeon
Wungki Jeon
SHSungho Hwang
Sungho Hwang
JKJae Joon Kim
Jae Joon Kim
MLMyunghee Lee
Myunghee Lee
This paper presents a driving circuitry system for high-resolution, pixelated-LED automotive headlamps. The system consists of an array of pixel drivers, and a row/column driver suitable for an active-matrix array configuration with the individual dimming control capabilities on each pixelated-LED. An asynchronous serial communication protocol is introduced to minimize the number of data transmission interface signals between the row/column driver and pixel drivers. The proposed pixel driver is designed to drive each pixelated-LED with constant current and pulse width modulation (PWM). It contains a memory cell for dimming data, and a sample-and-hold driver stage to minimize the static power consumption of the pixel driver. The proposed system has been fabricated by using a 0.18- $\mu \text{m}$ CMOS process. The test chip includes a $2\times16$ pixel array with an embedded row/column driver. The functional operation has been verified with an $8\times16$ LED array system prototype.