Woojin Hong

Woojin Hong

Auto-generated profile, based on publicly available information

Woojin Hong

Department of Electrical Engineering, Ulsan National Institute of Science and Technology, Ulsan, South Korea

Research Focus & Metrics

Academic Career Length

7Years (2020-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 June 2020 in IEEE Transactions on Circuits and Systems I: Regular Papers
Verified
Journal Article
Closed access
WHWoojin Hong
Woojin Hong
MLMyunghee Lee
Myunghee Lee
The growth of IoT applications requires DC-DC converters to have small printed circuit board (PCB) areas and high efficiency over a wide load range. A multi-mode operation of DC-DC converters, therefore, is often necessary to achieve this high efficiency over a wide load range. This paper introduces a tri-mode DC-DC buck converter for IoT applications. The tri-mode operation with PWM, PFM, and multiple-sawtooth PWM (MSPWM) modes helps to retain the high efficiency over the wide load range. The MSPWM mode also enhances a noise margin of the converter, ensuring a regular switching operation at an ultra-light load condition. With a load current prediction scheme, the proposed tri-mode converter requires neither additional load current sensor nor multiple mode controllers. In addition, a soft-start operation is employed to prevent an in-rush current. The proposed tri-mode buck converter has been fabricated through a 0.18-μm CMOS process with a chip area of 0.97 mm x 0.88 mm. A load-dependent seamless mode transition is realized, and a maximum converter efficiency of 91% has been measured with a 7.4-MHz switching frequency.

11 January 2021 in IEEE Journal of Solid-State Circuits
Verified
Journal Article
Closed access
WHWoojin Hong
Woojin Hong
MLMyunghee Lee
Myunghee Lee
In this article, a dual-ramp modulation scheme is proposed to solve an instability during the discontinuous conduction mode (DCM) operation of current-mode constant on-time (COT) controlled boost converters. A duty cycle-dependent auxiliary waveform, which is generated by the proposed capacitor-coupled common-drain amplifier (CCCDA), is summed with an inductor current information to form a current feedback loop. With the proposed scheme, the pulse frequency modulation (PFM) operation can be spontaneously accompanied by the current-mode COT control to enhance a light-load efficiency. In addition, a translinear loop (TLL)-based valley current sensor is introduced to sense a valley inductor current while solving the response time and stability problems of the previous SenseFET-based current sensor. An adaptive ON-time (AOT) generator provides a quasi-fixed switching frequency in the CCM operation regardless of the conversion ratio. The proposed boost converter has been fabricated using a 0.18- μm CMOS process with a total chip area of 1.23 mm × 1.37 mm. It achieves a peak efficiency of 94.5% even at a high-switching frequency of 10 MHz, and smooth mode transition between PFM and pulsewidth modulation (PWM) operations depending on the load conditions.

24 August 2021 in IEEE Transactions on Power Electronics
Verified
Journal Article
Closed access
WHWoojin Hong
Woojin Hong
MLMyunghee Lee
Myunghee Lee
This letter presents a high-frequency boost converter using an accurate feedforward-path current sensor for the fast-load transient response. To operate with the switching frequency of up to 25 MHz, the proposed current sensor senses the inductor current with a fast-sensing response time of about 4.5 ns. It also provides more accurate sensing gain than previous current sensors. In addition, the adaptive on -time control method is used for the proposed converter to further enhance the transient responses. The converter has been fabricated using a 0.18- μ m CMOS process with a total chip area of 1.3 × 1.12 mm. It achieves a fast-load transient of only 1 μ s at a 400-mA load step, and peak efficiency of 91.5 and 88.2% at switching frequencies of 15 and 25 MHz, respectively.

27 April 2023 in IEEE Transactions on Very Large Scale Integration (VLSI) Systems
Verified
Journal Article
Closed access
WKWoojung Kim
Woojung Kim
WHWoojin Hong
Woojin Hong
JKJae Joon Kim
Jae Joon Kim
MLMyunghee Lee
Myunghee Lee
This article proposes a single-loop referenceless clock and data recovery (CDR) with a bilateral bang-bang phase and frequency detector (BBPFD). The CDR achieves an unlimited frequency acquisition range in both directions of the lock frequency. The proposed BBPFD tracks the frequency by using the asymmetry of UP/DN output probability of the bang-bang phase detector (BBPD). A seamless transition between frequency acquisition and phase tracking is possible through a simple modification of the existing BBPD. The CDR has a locking time of $3 \mu \text{s}$ under the PRBS7 pattern. The test chip was fabricated in a 28-nm CMOS process. It supports a 5.4-Gb/s link rate, making it compatible with the embedded DisplayPort (eDP) standard v1.2. The total power consumption is 3.04 mW at a speed of 5.4 Gb/s/lane. The power efficiency is 0.57-pJ/bit at a supply voltage of 0.9 V.

15 October 2025 in IEEE Journal of Solid-State Circuits
Verified
Journal Article
Closed access
WHWoojin Hong
Woojin Hong
HKHyebong Ko
Hyebong Ko
JSJinwoo So
Jinwoo So
WHWoonhyung Heo
Woonhyung Heo
YCYonghwan Cho
Yonghwan Cho
HYHwayeal Yu
Hwayeal Yu
Foldable mobile applications recently have been leading the battery charger to have a slim height with a small form-factor and high efficiency at higher input voltages to increase the power density. Another trend for mobile applications is the power sharing, which enables to supply two mobile devices simultaneously. To meet these requirements, this article presents a dual-input bidirectional three-level battery charger. With the dual-input bidirectional structure, it can support the battery charging while supplying the wireless power-sharing device at the same time. Besides, a proposed coarse-fine flying capacitor voltage ( $V$ CF) balancer can achieve accurate and fast balancing even during the bidirectional operation. In addition, a frequency foldback controller extends an effective duty ratio to have a wide voltage conversion ratio (VCR). The proposed charger has been fabricated using a 130-nm BCD process with a total chip area of $4.4\times 4.2$ mm. It achieves a seamless bidirectional operation with a well-balanced $V$ CF, a peak charging efficiency of 96.8%, and a maximum VCR of 92.9%.