Florian Schönl

Mr. Florian Schönl

orcid

Research Focus & Metrics

Academic Career Length

8Years (2019-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
2 April 2019 in Materials
Verified
Journal Article
Open access
PDF file
Simon BardSimon Bard
Simon Bard
FSFlorian Schönl
Florian Schönl
MDMartin Demleitner
Martin Demleitner
Volker AltstädtVolker Altstädt
Volker Altstädt
Thermal conductivity is an important material property for thermo-mechanical calculations, as mechanical properties strongly depend on the temperature and heat distribution in the manufactured parts. Although several suggestions for approximation formulae have been made, existing experimental data are rare and are not comparable due to different measurement methods. In addition, scarcely has the thermal conductivity in both the fiber direction and transverse direction been studied. The aim of the current research is to show the influence of carbon fiber volume content on the thermal conductivity of laminates. The values are then used to verify the micromechanical models used in the literature. A strong influence on the thermal conductivity could be determined. For the transverse thermal conductivity, the correlation was exponential; for the conductivity in the fiber direction, a linear correlation was found.

7 May 2019 in Polymers
Verified
Journal Article
Open access
PDF file
Simon BardSimon Bard
Simon Bard
FSFlorian Schönl
Florian Schönl
MDMartin Demleitner
Martin Demleitner
Volker AltstädtVolker Altstädt
Volker Altstädt
In this paper, the thermal and electrical conductivity and mechanical properties of fiber reinforced composites produced from nickel- and copper-coated carbon fibers compared to uncoated fibers are presented. The carbon fibers were processed by our prepreg line and cured to laminates. In the fiber direction, the thermal conductivity doubled from ~3 W/mK for the uncoated fiber, to ~6 W/mK for the nickel, and increased six times to ~20 W/mK for the copper-coated fiber for a fiber volume content of ~50 vol %. Transverse to the fiber, the thermal conductivity increased from 0.6 W/mK (uncoated fiber) to 0.9 W/mK (nickel) and 2.9 W/mK (copper) at the same fiber content. In addition, the electrical conductivity could be enhanced to up to ~1500 S/m with the use of the nickel-coated fiber. We showed that the flexural strength and modulus were in the range of the uncoated fibers, which offers the possibility to use them for lightning strike protection, for heatsinks in electronics or other structural heat transfer elements.

10 September 2024 in Journal of the Mechanical Behavior of Biomedical Materials
Verified
Journal Article
Open access
FSFlorian Schönl
Florian Schönl
MDMartin Demleitner
Martin Demleitner
JAJörg Angermann
Jörg Angermann
PFPascal Fässler
Pascal Fässler
ILIris Lamparth
Iris Lamparth
HRHolger Ruckdaeschel
Holger Ruckdaeschel
3D printing of materials which combine fracture toughness, high modulus and high strength is quite challenging. Most commercially available 3D printing resins contain a mixture of multifunctional (meth)acrylates. The resulting 3D printed materials are therefore brittle and not adapted for the preparation of denture bases. For this reason, this article focuses on toughening by incorporation of triblock copolymers in methacrylate-based materials. In a first step, three urethane dimethacrylates with various alkyl spacer length were synthesized in a one-pot two-step synthesis. Each monomer was combined with 2-phenoxyethyl methacrylate as a monofunctional monomer and a polycaprolactone-polydimethylsiloxane-polycaprolactone triblock copolymer was added as toughener. The formation of nanostructures via self-assembly was proven by small angle X-ray scattering (SAXS) and transmission electron microscopy (TEM). The addition of the triblock copolymer resulted in a strong increase in fracture toughness for all mixtures. The nature of the urethane dimethacrylate had a significant impact on fracture toughness and flexural strength and modulus of the cured materials. Most promising systems were also investigated via dynamic fatigue propagation da/dN measurements, confirming that the toughening also works under dynamic load. By carefully selecting the length of the urethane dimethacrylate spacer and the amount of block copolymer, materials with the desired physical properties could be efficiently formulated. Especially the formulation containing the medium alkyl spacer length (DMA2/PEMA) and 5 wt% BCP1 (block copolymer), exhibits excellent mechanical properties and high fracture toughness.

Verified
Journal Article
Open access
PDF file
FBFlorian Braunbeck
Florian Braunbeck
FSFlorian Schönl
Florian Schönl
TPTimo Preußler
Timo Preußler
HRHans-Christian Reuss
Hans-Christian Reuss
MDMartin Demleitner
Martin Demleitner
PBPhilipp Berendes
Philipp Berendes
This study presents a thermoset moulding compound designed for electrical machines with high power densities. The compound reduces residual stresses induced by the difference in thermal expansion during use and by shrinkage in the compound during the manufacturing process. To reduce the internal stresses in the compound, in the electrical sheet lamination and at their interface, first the moulding’s coefficient of thermal expansion (CTE) must match that of the lamination because the CTE of the electrical sheets cannot be altered. Second, the shrinkage of the compound needs to be minimized because the moulding compound is injected around a prefabricated electrical sheet lamination. This provides greater freedom in the design of an electric motor or generator, especially if the thermoset needs to be directly bonded to the electrical sheet. The basic suitability of the material for the injection moulding process was iteratively optimised and confirmed by spiral flow tests. Due to the reduction of the residual stresses, the compound enables efficient cooling solutions for electrical machines with high power densities. This innovative compound can have a significant impact on electric propulsion systems across industries that use laminated electrical sheets.

10 September 2023
Verified
Book Chapter
Closed access
PDF file
FSFlorian Schönl
Florian Schönl
FHFabian Hübner
Fabian Hübner
MLMarius Luik
Marius Luik
JTJeremias Thomas
Jeremias Thomas
RARodrigo de Albuquerque
Rodrigo de Albuquerque
HRHolger Ruckdaeschel
Holger Ruckdaeschel