Simon Bard

Mr. Simon Bard

University of Bayreuth
orcid

Research Focus & Metrics

Academic Career Length

9Years (2018-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
2 April 2019 in Materials
Verified
Journal Article
Open access
PDF file
Simon BardSimon Bard
Simon Bard
FSFlorian Schönl
Florian Schönl
MDMartin Demleitner
Martin Demleitner
Volker AltstädtVolker Altstädt
Volker Altstädt
Thermal conductivity is an important material property for thermo-mechanical calculations, as mechanical properties strongly depend on the temperature and heat distribution in the manufactured parts. Although several suggestions for approximation formulae have been made, existing experimental data are rare and are not comparable due to different measurement methods. In addition, scarcely has the thermal conductivity in both the fiber direction and transverse direction been studied. The aim of the current research is to show the influence of carbon fiber volume content on the thermal conductivity of laminates. The values are then used to verify the micromechanical models used in the literature. A strong influence on the thermal conductivity could be determined. For the transverse thermal conductivity, the correlation was exponential; for the conductivity in the fiber direction, a linear correlation was found.

7 May 2019 in Polymers
Verified
Journal Article
Open access
PDF file
Simon BardSimon Bard
Simon Bard
FSFlorian Schönl
Florian Schönl
MDMartin Demleitner
Martin Demleitner
Volker AltstädtVolker Altstädt
Volker Altstädt
In this paper, the thermal and electrical conductivity and mechanical properties of fiber reinforced composites produced from nickel- and copper-coated carbon fibers compared to uncoated fibers are presented. The carbon fibers were processed by our prepreg line and cured to laminates. In the fiber direction, the thermal conductivity doubled from ~3 W/mK for the uncoated fiber, to ~6 W/mK for the nickel, and increased six times to ~20 W/mK for the copper-coated fiber for a fiber volume content of ~50 vol %. Transverse to the fiber, the thermal conductivity increased from 0.6 W/mK (uncoated fiber) to 0.9 W/mK (nickel) and 2.9 W/mK (copper) at the same fiber content. In addition, the electrical conductivity could be enhanced to up to ~1500 S/m with the use of the nickel-coated fiber. We showed that the flexural strength and modulus were in the range of the uncoated fibers, which offers the possibility to use them for lightning strike protection, for heatsinks in electronics or other structural heat transfer elements.

31 May 2019 in Polymers
Verified
Journal Article
Open access
PDF file
Simon BardSimon Bard
Simon Bard
MDMartin Demleitner
Martin Demleitner
RWRegino Weber
Regino Weber
RZRico Zeiler
Rico Zeiler
Volker AltstädtVolker Altstädt
Volker Altstädt
The aim of the underlying research is to understand the effect of elevated test temperatures on the mechanical properties of carbon fiber-reinforced laminates based on three different hardeners. A high-temperature stable adhesive was developed for the end tabs of the specimen. Bifunctional bisphenol A diglycidyl ether (DGEBA) epoxy cured with triethylenetetramine (TETA), isophorone diamine (IPDA), and 4,4′-diaminodiphenylsulfone (DDS) were cured and tested in a Celanese compressive test up to 250 °C. A model by Feih was applied, and sufficient accordance (R2 > 97%) with the compressive data was found. We showed that the network density and the chemical structure of the thermoset network influenced the compressive behavior.

2 May 2019 in Polymers
Verified
Journal Article
Open access
PDF file
CBChristian Bethke
Christian Bethke
SSSandra A. Sanchez-Vazquez
Sandra A. Sanchez-Vazquez
DRDaniel Raps
Daniel Raps
GBGökhan Bakis
Gökhan Bakis
Simon BardSimon Bard
Simon Bard
Volker AltstädtVolker Altstädt
Volker Altstädt
The present study focuses on the processing and properties of epoxy foams by the use of CO2 blocked hardener N-aminoethylpiperazine (B-AEP) and different resins. Although some studies described the foaming with carbamates, little attention has been given to the interaction of resin properties (such as viscosity) on the foaming performance. Therefore, two resins, diglycidyl ether of bisphenol-A (DGEBA) and epoxy novolac (EN), as well as their 50:50 blend, were foamed with B-AEP and unblocked/blocked AEP hardener mixtures in a batch foaming process. Furthermore, the commercially available chemical blowing agent para-toluenesulfonyl hydrazide (TSH) was used as a benchmark for commonly used chemical blowing agents. The lowest density in this study was reached by the DGEBA+B-AEP system in the range of 215 kg/m3 with the drawback of an inhomogeneous cell structure and high cell size distribution. The best cell morphology and lowest cell size distribution was reached with the EN+15:85% unblocked:blocked hardener mixture, resulting in a density in the range of 394 kg/m3. A syntactic foam was achieved by a DGEBA+50:50% unblocked:blocked hardener mixture with a density of around 496 kg/m3. It was found that a higher viscosity of the resin lead to an increase in the density and a decrease in the cell size distribution range as a result of a closer expansion time window.

Verified
Journal Article
Open access
PDF file
Simon BardSimon Bard
Simon Bard
MDMartin Demleitner
Martin Demleitner
MRMarius Radtke
Marius Radtke
Volker AltstädtVolker Altstädt
Volker Altstädt
The thermal conductivity of carbon fiber reinforced polymers is crucial for new technologies and is used in cutting-edge technologies such as sensors, heated rollers and anti-icing of airplane wings. Researchers so far focused on coating conventional prepregs with thermally conductive materials to enhance the transversal conductivity. Another strategy is followed in this study: Thermally conductive matrices filled with graphite platelets were processed by a laboratory prepreg line. Laminates produced from this type of prepregs show an enhancement in thermal conductivity by 3.3 times with a 20 vol% filler content relative to the matrix, and a 55 vol% fiber volume content in the laminate. The research shows that the incorporation of conductive particles in the matrix is more effective for increasing the conductivity than previous methods.

1 January 2018 in Procedia Structural Integrity
Verified
Journal Article
Open access
Simon BardSimon Bard
Simon Bard
MDMartin Demleitner
Martin Demleitner
MHMarkus Häublein
Markus Häublein
Volker AltstädtVolker Altstädt
Volker Altstädt