Information encryption technique has broad applications in individual privacy, military confidentiality, and national security, but traditional electronic encryption approaches are increasingly unable to satisfy the demands of strong safety and large bandwidth of high-speed data transmission over network. Optical encryption technology could be more flexible and effective in parallel programming and multiple degree-of-freedom data transmitting application. Here, we show a dual-layer optical encryption fluorescent polymer waveguide chip based on optical pulse-code modulation technique. Fluorescent oligomers were doped into epoxy cross-linking SU-8 polymer as a gain medium. Through modifying both the external pumping wavelength and operating frequency of the pulse-code modulation, the sender could ensure the transmission of vital information is secure. If the plaintext transmission is eavesdropped, the external pumping light will be switched, and the receiver will get warning commands of ciphertext information in the standby network. This technique is suitable for high-integration and high-scalability optical information encryption communications.

A point contact model is developed to analyze the fundamental characteristics of a single-mode actuation type linear piezoelectric actuator in this paper. The prototype is a plate type piezoelectric actuator using two-phase excitation, which realizes bi-directional motion by changing the vibration mode within different exciting frequencies. Differs from other models, the vibration of barycenter of the stator is taken into account, and the trajectories of driving tip are simulated and measured with and without consideration of the mechanical contact. The results show that a spiral reciprocating motion is generated at driving tip while taking into account the contact and vibration of barycenter of stator. Furthermore, the contact state between the driving tip and linear guide is analyzed by discussing the influence of some important factors including preload and exciting voltage. In addition, the behavior of the force transmission between the driving tip and linear guide is investigated via the classic coulomb friction model to understand the drive mechanism of the single-mode actuation type actuator. Finally, the relations between the output speed and various inputs to the actuator are studied by numerical simulations, which are validated by experiments. It is shown that experimental results are in good agreement with simulation results, which verifies the effectiveness of the proposed model.

Because of the ease with which oxide films form on its surfaces, stainless steel has strong corrosion resistance and excellent processing performance. Electrochemical machining (ECM) is a flexible process that can create microstructures on stainless steel (SS304); however, with traditional masked ECM, the efficiency and accuracy of microstructure machining are low. Proposed here is the use of a non-Newtonian fluid [polyacrylamide (PAM)] as the electrolyte. To date, there have been few papers on the electrochemical dissolution behavior of stainless-steel micromachining with a non-Newtonian fluid as the electrolyte. The aims of the study reported here were to investigate the electrochemical properties of SS304 with PAM and PAM–NaOH as electrolytes, and to explain their electrochemical corrosion mechanisms. The effects of different electrolytes were compared, and the polarization curves of SS304 in PAM and PAM–NaOH electrolyte solutions with different components were analyzed and compared with that in NaNO₃ electrolyte. Then, the effects of the main processing parameters (pulse voltage, frequency, and duty ratio) on the machining performance were investigated in detail. A microhole array was obtained with a good quality comprising an average diameter of 330.11 µm, an average depth of 16.13 µm, and a depth-to-diameter ratio of 0.048. Using PAM to process microstructures on stainless-steel surfaces was shown to be feasible, and experiments indicated that the mixed electrolyte (PAM–NaOH) had not only the physical characteristics of a non-Newtonian fluid but also the advantages of a traditional electrolyte to dissolve processing products, and it effectively improved the processing accuracy of masked ECM for SS304.

As the thickness of an ultra-thin flattened heat pipe (UTHP) decreases, the fabrication difficulty increases exponentially, and the thermal performance deteriorates rapidly. In this study, three types of composite wicks were developed for UTHPs with a 0.6 mm thickness: copper foam and mesh wick (CFMW), two layers of different mesh wick (TDMW), and three layers of the same mesh wick (TSMW). The startup and steady-state performances of the UTHPs with liquid filling ratios of 60% to 120% were investigated. The findings indicated that the CFMW UTHP with a filling ratio of 100% exhibited the best startup performance, with the highest equilibrium temperature of 58.37 °C. The maximum heat transport capacities of the CFMW, TDMW, and TSMW UTHP samples were 9, 8, and 8.5 W, respectively, at their corresponding optimum filling ratios of 110%, 90%, and 100%. The CFMW UTHP exhibited the lowest evaporation and condensation thermal resistances of 0.151 and 0.189 K/W, respectively, which were 24.67% and 41.85% lower than those of the TSMW UTHP. CFMW can be used to improve the thermal performance of UTHPs. This study provides important guidelines for the structural design, fabrication technology, and performance improvement of high-performance UTHPs used in portable electronic devices.

Magnetorheological–chemical-polishing tests are carried out on single-crystal silicon carbide (SiC) to study the influence of the process parameters on the polishing effect, predict the polishing results via a back propagation (BP) neural network, and construct a model of the processing parameters to predict the material removal rate (MRR) and surface quality. Magnetorheological–chemical polishing employs mechanical removal coupled with chemical action, and the synergistic effect of both actions can achieve an improved polishing effect. The results show that with increasing abrasive particle size, hydrogen peroxide concentration, workpiece rotational speed, and polishing disc rotational speed, the MRR first increases and then decreases. With an increasing abrasive concentration and carbonyl iron powder concentration, the MRR continues to increase. With an increasing machining gap, the MRR shows a continuous decrease, and the corresponding changes in surface roughness tend to decrease first and then increase. The prediction models of the MRR and surface quality are constructed via a BP neural network, and their average absolute percentage errors are less than 2%, which is important for the online monitoring of processing and process optimisation.

Linear ultrasonic motors can output large thrust stably in a narrow space. In this paper, a plate linear ultrasonic motor is studied. Firstly, the configuration and operating principle of the $\Pi$-type linear ultrasonic motor is illustrated. Then, two slotting schemes are put forward for the stator to enlarge the amplitude of the driving foot and improve the output performance of motor. After that, a novel optimization method based on the power flow method is suggested to describe the energy flow of stator, so as to estimate the slotting schemes. Finally, the prototypes are manufactured and tested. The experimental results show that the output performance of both new motors are excellent. The maximum output thrust of the arc slotted motor is 76 N/94 N, and the corresponding maximum no-load speed is 283 mm/s/213 mm/s, while the maximum output thrust of V-slotted motor reaches 90 N/120 N, and the maximum no-load speed reaches 223 mm/s/368 mm/s.