In response to the fracturing disturbance problem in the Mahu 18 block, based on the production data of on-site fracturing disturbance well groups, the actual fracturing disturbance cases in the block were first statistically divided. The complex fracturing disturbance situation in the block was divided according to the relationship between the number of fracturing wells and the number of production wells. Then, the disturbance types were classified based on the production dynamic response characteristics of the disturbed wells, and the degree of disturbance was quantitatively evaluated for the different types. The results indicate two main types of fracturing interference in the Mahu 18 block: the fracture communication type, and the pressure wave interference type formed through inter-well connectivity through the reservoir matrix. The fracturing disturbance dominated by fracture communication can cause serious water channeling to the production well through the direct connection of inter-well fractures, leading to a surge in water production. This type of fracturing disturbance often has a severe negative impact on the production well. In addition, the pressure and production (water production, liquid production, oil production) in the production dynamic response characteristics of disturbed wells during fracturing disturbance were used as evaluation indicators to quantify the impact of different types of fracturing disturbance from multiple perspectives.
This study aims to enhance the development effectiveness of infill wells in the strongly heterogeneous conglomerate reservoir of the Baikouquan Formation in the Bai 21 well area of the Junggar Basin. By optimizing the synergy between fracturing and waterflooding development, it provides a basis for improving the recovery rate of such reservoirs. Integrating geomechanical modeling, fracturing numerical simulation, and reservoir dynamic analysis, the influence mechanisms of fracturing parameters—including pumping rate, pad fluid ratio, and proppant intensity—on fracture propagation, waterflooding response, and stress field evolution were systematically investigated. The results indicate that an optimal parameter combination of a pumping rate of 3.5–4.0 m3/min, a pad fluid ratio of 40–50%, and a proppant intensity of 3.0–4.0 m3/m can create short, wide fractures with half-lengths of 40–45 m, effectively delaying water breakthrough and reducing inter-well interference. Stress field simulations further reveal non-uniform evolution during injection and production: the stress near injection wells initially increases and then decreases, dropping by 9.3% compared to the initial value, while the stress around production wells continuously decreases, with a reduction of up to 37.3%. These findings provide valuable guidance for the synergistic development of fracturing and waterflooding in infill wells in similar strongly heterogeneous conglomerate reservoirs.
The Jimusar shale reservoir exhibits extremely low permeability, classified as an ultra-low porosity and ultra-low permeability formation. Crude oil mobility is poor, and the reservoir demonstrates significant heterogeneity. Conventional horizontal well fracturing development fails to meet requirements, facing issues such as pronounced energy depletion in the formation, unclear oil–water distribution, and changes in formation stress direction. Based on the reservoir properties of the Jimusar shale oil reservoir, this paper establishes a fracture propagation model for horizontal wellbore hydraulic fracturing and a reservoir numerical model. It simulates the evolution of pressure fields, stress fields, and seepage fields at different time points during the fracturing and production phases of horizontal wells. Results indicate the following: (1) When fracturing fluid is injected into the formation, oil saturation around fractures rapidly decreases. During the initial production phase, oil saturation around fractures increases due to the recovery of some fracturing fluid and the sorption effect between fracturing fluid and crude oil. (2) Formation pressure around horizontal wells significantly increases upon fracturing fluid injection. The dual effects of fracture opening and fluid injection cause stress to rise near fractures. During production, both formation pressure and stress decrease near the wellbore, with greater pressure reduction in the near-wellbore zone than in the far-wellbore zone. However, formation stress decreases less near the wellbore due to stress concentration effects from fracture opening, resulting in a smaller reduction than in the far-wellbore zone. (3) The formation surrounding the fracture undergoes dual influences from fracture opening and fracturing fluid injection, causing deflection in the direction of near-wellbore stress. During the initial production phase, the impact of stress deflection gradually diminishes with ongoing production. However, after prolonged production, the deflection of formation stress intensifies. The conclusion states that this understanding clarifies the multi-field evolution patterns in fracturing production for horizontal well clusters, providing theoretical guidance for subsequent shale development processes.
This research investigates strategies for improving oil recovery from the highly heterogeneous conglomerate deposits of the Lower Karamay Formation in the Bai 21 Well Block of the Junggar Basin. Particular attention is given to the coordinated application of hydraulic fracturing and waterflooding to enhance the effectiveness of infill well development. An integrated approach combining geomechanical modeling, numerical hydraulic-fracturing simulation, and reservoir performance analysis was employed to systematically investigate the effects of proppant ratio, temporary plugging, and proppant placement intensity on fracture propagation, waterflood response, and stress-field evolution. The results show that a proppant ratio of 0.15 and a proppant placement intensity of 2.5 m3/m, combined with temporary plugging and diversion fracturing, can generate short and wide fractures with half-lengths of 40–45 m, effectively mitigating early water channeling and reducing interwell interference. In situ, stress-field simulations further indicate that the stress field evolves non-uniformly during injection and production. The average formation stress initially decreases and subsequently increases, with a maximum reduction of 13.7% relative to the initial value. As waterflooding progresses, the stress gradually recovers, resulting in a final reduction of 10.7%. These findings provide an important reference for the coordinated design of infill-well hydraulic fracturing and waterflooding development in similarly highly heterogeneous conglomerate reservoirs.
The Jimsar shale reservoir is characterized by low porosity and low permeability. Multistage fracturing of horizontal wells is an effective development method. However, interference between multiple fractures and the presence of well-developed bedding planes limit the effective extension of fractures. To elucidate the initiation and propagation mechanisms of inter-bed fractures in horizontal multi-stage fracturing within shale reservoirs, this study focuses on the Jimusar Shale outcrop and employs large-scale true triaxial hydraulic fracturing physical simulation experiments to construct an experimental model of horizontal multi-stage fracturing. By analyzing fracture morphology, propagation paths, and bedding plane activation characteristics, the study elucidates the fracture propagation patterns under various conditions. Results indicate the following: (1) Increasing the fluid injection rate enhances the net pressure at the fracture tip, effectively overcoming the resistance of bedding planes and promoting the continued propagation of hydraulic fractures across bedding interfaces. (2) Stage spacing affects the coordinated propagation of hydraulic fractures by modifying the stress shadow effect between adjacent fractures. A smaller stage spacing intensifies stress interference, leading to the suppression of local fracture propagation and an increased likelihood of fracture communication. (3) The horizontal stress difference is the primary controlling factor governing fracture propagation direction and bedding penetration capability. A larger horizontal stress difference promotes stable fracture propagation along the direction of the maximum horizontal principal stress and facilitates penetration through bedding planes, whereas a lower horizontal stress difference favors bedding plane activation and fracture deflection, resulting in the formation of a more complex fracture network. The study has established an understanding of the fracture expansion laws under different parameter conditions, which can provide theoretical basis and technical support for the optimization design of multi-stage fracturing parameters in horizontal shale oil wells and the efficient modification of reservoirs.