Due to the increasing use of multi-material constructions and the resulting material incompatibilities, mechanical joining technologies are gaining in importance. The reasons for this are the variety of joining possibilities as well as high load-bearing capacities. However, the currently rigid tooling systems cannot react to changing boundary conditions, such as changed sheet thicknesses or strength. For this reason, a large number of specialised joining processes have been developed to expand the range of applications. Using a versatile self-piercing riveting process, multi-material structures are joined in this paper. In this process, a modified tool actuator technology is combined with multi-range capable auxiliary joining parts. The multi-range capability of the rivets is achieved by forming the rivet head onto the respective thickness of the joining part combination without creating a tooling set-up effort. The joints are investigated both experimentally on the basis of joint formation and load-bearing capacity tests as well as by means of numerical simulation. It turned out that all the joints examined could be manufactured according to the defined standards. The load-bearing capacities of the joints are comparable to those of conventionally joined joints. In some cases the joint fails prematurely, which is why lower energy absorptions are obtained. However, the maximum forces achieved are higher than those of conventional joints. Especially in the case of high-strength materials arranged on the die side, the interlock formation is low. In addition, the use of die-sided sheets requires a large deformation of the rivet head protrusion, which leads to an increase in stress and, as a result, to damage if the rivet head. However, a negative influence on the joint load-bearing capacity could be excluded.
Similar to bulk metal forming, clinch joining is characterised by large plastic deformations and a variety of different 3D stress states, including severe compression. However, inherent to plastic forming is the nucleation and growth of defects, whose detrimental effects on the material behaviour can be described by continuum damage models and eventually lead to material failure. As the damage evolution strongly depends on the stress state, a stress-state-dependent model is utilised to correctly track the accumulation. To formulate and parameterise this model, besides classical experiments, so-called modified punch tests are also integrated herein to enhance the calibration of the failure model by capturing a larger range of stress states and metal-forming-specific loading conditions. Moreover, when highly ductile materials are considered, such as the dual-phase steel HCT590X and the aluminium alloy EN AW-6014 T4 investigated here, strong necking and localisation might occur prior to fracture. This can alter the stress state and affect the actual strain at failure. This influence is captured by coupling plasticity and damage to incorporate the damage-induced softening effect. Its relative importance is shown by conducting inverse parameter identifications to determine damage and failure parameters for both mentioned ductile metals based on up to 12 different experiments.
As a widely used sheet metal in clinched joints within the automotive industry, the aluminum alloy EN AW-6014 has been the focus of numerous studies. High-cycle fatigue (HCF) is a critical aspect when assessing the durability of clinched joints. In the present work, the HCF behavior of EN AW-6014 T4 was explored both experimentally and numerically. To model the fatigue behavior, Lemaitre’s two-scale damage model was used. Two key parameters, damage strength and damage exponent, are necessary for numerical investigations of HCF behavior. These parameters were determined through experiments with flat specimens and subsequently validated within a numerical model of clinched joints. The numerical results for fatigue match the experimental ones of the clinched joints quite well.
21 October 2016 in Journal of Materials Science Research
Lightweight design in vehicles leads to an increasing use of fibre-reinforced-plastics (FRP). To ensure the possibility of detachable joints in those constructions specific joining technologies have to be developed. Available technologies are not suitable for mass production or are leading to damage in the FRP. The aim of this paper is to show the possibilities and the general feasibility of a new process approach for the application of functional elements in FRP or hybrid materials during resin transfer moulding (RTM) processes. Therefore the movement of the RTM-tool-punch is utilised to produce an interlock between the splay stud and the fibres of the non-consolidated preform. This enables the application of the elements during the RTM-process. The resin infusion leads to the consolidation of the CFRP and a further fixation of the splay stud. Pull-out-tests as well as torsion tests are showing the mechanical performance of the joints.
Self-piercing riveting (SPR) is a well-established joining technique in lightweight construction, as it enables the joining of different materials without requiring pre-drilling. However, the necessary adaptation of the rivet-die combination to the respective material and thickness combinations requires a large number of specific tool sets, which significantly limits the process's flexibility. To overcome these limitations, the versatile self-piercing riveting (V-SPR) was developed, which features enhanced punch actuation in combination with a multi-range-capable rivet . In this context, the concept of a movable die was introduced, which enables an extended process window and adaptable joint formation. Kappe et al. presented initial studies demonstrating the potential of this approach . However, a detailed numerical understanding of the underlying mechanisms remains lacking. This paper presents a numerical analysis of V-SPR with a movable die using a finite element (FE) model. The model includes deformable rivets, sheet metal materials and a kinematically controlled die with adjustable movement. A parameter study was conducted to analyse the influence of die movement on the material flow of the rivet and sheets, as well as joint formation. The simulations were validated using selected experimental data. The goal is to compare the joint geometries achieved with fixed and moving dies and expand the process windows of VSPR. The results demonstrate that the movable-die concept significantly enhances the material flow of both the sheets and the rivet, resulting in a noticeably larger and more reliable interlock than what is achievable with V-SPR using a fixed die. The numerical analyses support the observations reported by Kappe et al. and extend them by providing a quantitative description of how die displacement influences the resulting interlock size. Moreover, the ability to precisely control the die movement makes it possible to join challenging sheet-metal combinations that are difficult to process with conventional setups, particularly in cases involving thicker sheet materials.