A textile material’s electromagnetic interference (EMI) shielding effectiveness mainly depends on the material’s electrical conductivity and porosity. Enhancing the conductivity of the material surface can effectively improve the electromagnetic shielding effectiveness. However, the use of highly conductive materials increases production cost, and limits the enhancement of electromagnetic shielding effectiveness. This work aims to improve the EMI shielding effectiveness (EMSE) by using an ultrathin multilayer structure and the air-permeable textile MEFTEX. MEFTEX is a copper-coated non-woven ultrathin fabric. The single-layer MEFTEX SE test results show that the higher its mass per unit area (MEFTEX 30), the better its SE property between 56.14 dB and 62.53 dB in the frequency band 30 MHz–1.5 GHz. Through comparative testing of three groups samples, a higher electromagnetic shielding effect is obtained via multilayer structures due to the increase in thickness and decrease of volume electrical resistivity. Compared to a single layer, the EMI shielding effectiveness of five layers of MEFTEX increases by 44.27–83.8%. Due to its ultrathin and porous structure, and considering the balance from porosity and SE, MEFTEX 10 with three to four layers can still maintain air permeability from 2942 L/m2/s–3658 L/m2/s.
In response to the growing demand for lightweight yet robust materials in electric vehicle (EV) battery casings, this study introduces an advanced carbon fiber-reinforced composite (CFRC). This novel material is engineered to address critical aspects of EV battery casing requirements, including mechanical strength, electromagnetic interference (EMI) shielding, and thermal management. The research strategically combines carbon composite components with copper-plated polyester non-woven fabric (CFRC/Cu) and melamine foam board (CFRC/Me) into a sandwich-structure composite plus a series of composites with graphite particle-integrated matrix resin (CFRC+Gr). Dynamic mechanical analysis (DMA) revealed that the inclusion of copper-plated fabric significantly enhanced the stiffness, and the specific tensile strength of the new composites reached 346.8 MPa/(g/cm3), which was higher than that of other metal materials used for EV battery casings. The new developed composites had excellent EMI shielding properties, with the highest shielding effectives of 88.27 dB from 30 MHz to 3 GHz. Furthermore, after integrating the graphite particles, the peak temperature of all composites via Joule heating was increased. The CFRC+Gr/Me reached 68.3 °C under a 5 V DC power supply after 180 s. This research presents a comprehensive and innovative approach that adeptly balances mechanical, electromagnetic, and thermal requirements for EV battery casings.
Electromagnetic interference shielding clothing has been developed for people who is sensitive to electromagnetic radiation or workers working under extremely high electromagnetic radiation circumstances. The challenge was developing the fabric with good washability, durability, and air permeability. After three machine washing cycles, the electromagnetic interference shielding effectiveness can drop more than 99% for untreated copper-coated fabric. In this research, the chlorinated poly-para-xylylene (parylene C) encapsulating technology was used to protect the fiber's copper particles. The result shows that the treated sample's washing ability will significantly improve after processing 15 g parylene-C on the copper-coated fabrics. The electromagnetic interference shielding effectiveness can remain at 39.93 dB and 25 dB on average from 30 MHz to 3 GHz after 10 hand washing cycles and 10 machine washing cycles, respectively. The air permeability remains around 1043.6 mm/s for a 15 g parylene-C encapsulated sample. The chemical resistance property was also improved significantly after encapsulation of 15 g parylene-C. For the 15 g parylene-C encapsulated samples, there is less than 3% loss of electromagnetic interference shielding effectiveness after 8 h of immersing into pH = 2 and pH = 12 solution. The overall structure of the 15 g parylene-C encapsulated fabric remains intact after 6000 abrasion cycles. The study presents an effective method for fabricating highly durable, comfortable electromagnetic interference shielding fabric, guaranteeing reliability for technical clothing applications and showing great potential for further development.
26 February 2023 in Journal of Industrial Textiles
This paper investigates the electromagnetic interference shielding effect and wearing comfort properties of a sandwich material consisting of a surface layer, an electromagnetic interference shielding layer, a thermal insulation layer, and a lining layer. The main aim is to research its potential as a winter jacket’s material for shielding electromagnetic radiation and the relationship between single-layer fabric samples and multi-layer sandwich materials under different properties. Experimentally, it is found that the electromagnetic interference shielding effectiveness of the sandwich materials is only determined by the electromagnetic interference shielding layer fabric sample, the other layers’ fabric samples have no significant impact on the electromagnetic interference shielding effect. In this paper, the air permeability of the sandwich materials is 25 to 50% lower than that of the single-layer fabric samples with the lowest air permeability in their combination. And the water vapor resistance of the sandwich materials is 40 to 60% higher than that of the single-layer fabric samples with the highest water vapor resistance in their combination. The thermal resistances of the sandwich materials measured by the Alambeta are lower than those calculated by the sum of the individual layers’ thermal resistance, which may be caused by the reduction in the internal air of the sandwich materials. Finally, the quality index evaluation is used to select the most suitable sandwich material for the winter jacket against electromagnetic radiation, which achieves the purpose of balancing the electromagnetic interference shielding effect and wearing comfort.
Carbon fiber reinforced epoxy resin matrix composite is one of the most important composite materials in the world. Many researchers have conducted a lot of research on epoxy resin matrix systems in recent years, mainly to improve the problem with the short curing time of the matrix system and epoxy resin's high viscosity. The final aim is to enhance various aspects of composites' performance and optimize the production process. A new type of water dispersed epoxy resin matrix system is investigated in this paper and the target is to optimize the mechanical, thermal, and electrical performances of the composites with the water dispersed epoxy resin matrix by varying different doping particles and different resin/catalyst ratios. Through a series of experiments, it is evident that varying the ratio of resin to catalyst in the matrix system will not significantly improve the mechanical as well as thermal properties of the composites. However, increasing the amount of catalyst in the matrix system can greatly improve the electrical properties of its composite samples. In addition to this, the addition of doping particles to the matrix systems has the effect of slightly enhancing the tensile modulus, thermal conductivity, and electrical conductivity of their composites.Highlights: A new water‐dispersed epoxy resin matrix system improves processing technology. Increasing amount of catalyst in the matrix system improves electrical resistivity. Adding particles to matrix systems has a slight effect on different properties.
1 January 2023 in Journal of Engineered Fibers and Fabrics
Textile-based electromagnetic interference (EMI) shielding materials with good flexibility and high EMI shielding effectiveness (SE) are highly desirable. Still, the poor mechanical properties of textile-based EMI shielding materials limit their application. The carbon filaments (CF) combine superior mechanical properties and conductivity. Therefore, we demonstrate the CF-reinforced material, which was laminated with two types of copper-coated nonwoven polyester (CuPET10 and CuPET20) for EMI shielding. Compared to the traditional lamination method, this process was more convenient by ironing with adhesive lining. The developed laminate (CuPET/CF) performs superior EMI shielding property with an average SE value of 88.6 dB in the frequency range of 30 MHz to 3 GHz. The mechanical properties were improved from 12.7 to 39.9 MPa and from 13.46 MPa to 35.78 MPa for CuPET10/CF and CuPET20/CF, respectively. The newly developed material also demonstrated exceptional lightweight, flexibility, and thermal resistance. The laminated CuPET/CF material provides enhanced mechanical properties and easy lamination capability, allowing it to shield surfaces of electromagnetic radiation-sensitive equipment while providing a certain degree of protection and extremely high EMI shielding efficiency.