Mpho Muloiwa

Dr. Mpho Muloiwa


Research Focus & Metrics

Academic Career Length

5Years (2022-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
6 December 2022 in Water Practice & Technology
Verified
Journal Article
Open access
PDF file
MMMpho Muloiwa
Mpho Muloiwa
MDM. O. Dinka
M. O. Dinka
Stephen Nyende-ByakikaStephen Nyende-Byakika
Stephen Nyende-Byakika
The biological aeration unit consumes the highest energy (67.3%) in wastewater treatment compared with physical (18.8%) and chemical (13.9%) treatment processes. The high energy consumption is caused by the supply of oxygen using air pumps/blowers and temperature that controls microorganisms' growth. The purpose of this study was to model and optimize energy consumption in the biological aeration unit. The multilayer perceptron (MLP) artificial neural network (ANN) algorithm was used to model energy consumption. The particle swarm optimization (PSO) algorithm was used to optimize the energy consumption model. Sensitivity analysis was performed to determine the percentage contribution of input variables towards energy consumption. The MLP ANN algorithm modelled energy consumption successfully and produced R², RMSE, and MSE of 0.89, 0.0265, and 0.00070, respectively, during the testing phase. The PSO algorithm optimized energy consumption successfully and produced a global solution of 0.993 kWh/m³. The percentage reduction between the lowest measured and optimized energy consumption was 38.4%. Aeration period (81%) and temperature (10.7%) contributed the highest towards energy consumption. In conclusion, temperature played a significant role in energy consumption compared with airflow rate (4.2%). When the temperature is conducive to allowing the growth of microorganisms, the removal of COD and ammonia will be rapid resulting in low energy consumption.

13 April 2023 in Engineering in Life Sciences
Verified
Journal Article
Open access
MMMpho Muloiwa
Mpho Muloiwa
MDMegersa Dinka
Megersa Dinka
SNStephen Nyende‐Byakika
Stephen Nyende‐Byakika
The biological treatment process is responsible for removing organic and inorganic matter in wastewater. This process relies heavily on microorganisms to successfully remove organic and inorganic matter. The aim of the study was to model biomass growth in the biological treatment process. Multilayer perceptron (MLP) Artificial Neural Network (ANN) algorithm was used to model biomass growth. Three metrics: coefficient of determination (R2), root mean squared error (RMSE), and mean squared error (MSE) were used to evaluate the performance of the model. Sensitivity analysis was applied to confirm variables that have a strong influence on biomass growth. The results of the study showed that MLP ANN algorithm was able to model biomass growth successfully. R2 values were 0.844, 0.853, and 0.823 during training, validation, and testing phases, respectively. RMSE values were 0.7476, 1.1641, and 0.7798 during training, validation, and testing phases respectively. MSE values were 0.5589, 1.3551, and 0.6081 during training, validation, and testing phases, respectively. Sensitivity analysis results showed that temperature (47.2%) and dissolved oxygen (DO) concentration (40.2%) were the biggest drivers of biomass growth. Aeration period (4.3%), chemical oxygen demand (COD) concentration (3.2%), and oxygen uptake rate (OUR) (5.1%) contributed minimally. The biomass growth model can be applied at different wastewater treatment plants by different plant managers/operators in order to achieve optimum biomass growth. The optimum biomass growth will improve the removal of organic and inorganic matter in the biological treatment process.

25 November 2022 in Water Science & Technology
Verified
Journal Article
Open access
PDF file
MMMpho Muloiwa
Mpho Muloiwa
MDMegersa Dinka
Megersa Dinka
Stephen Nyende-ByakikaStephen Nyende-Byakika
Stephen Nyende-Byakika
The biological treatment process (BTP) is responsible for removing COD and ammonia using microorganisms present in wastewater. The BTP consumes large quantities of energy due to the transfer of oxygen using air pumps/blowers. Energy consumption in the BTP is due to low solubility of oxygen, which results in low aeration efficiency (AE). The aim of the study was to develop an AE model that can be used to monitor the performance of the BTP. MLP ANN algorithm was used to model AE in the BTP. The performance of the AE model was evaluated using R2, MSE, and RMSE. Sensitivity analysis was performed on the AE model to determine variables that drive AE. The results of the study showed that MLP ANN algorithm was able to model AE. R2, MSE, and RMSE results were 0.939, 0.0025, and 0.05 respectively during testing phase. Sensitivity analysis results showed that temperature (34.6%), COD (21%), airflow rate (19.1%), and OTR/KLa (15.7%) drive AE. At high temperatures, the viscosity of wastewater is low which enables oxygen to penetrate the wastewater, resulting in high AE. The AE model can be used to predict the performance of the BTP, which will assist in minimizing energy consumption.

1 April 2024 in Water and Environment Journal
Verified
Journal Article
Open access
PDF file
MMMpho Muloiwa
Mpho Muloiwa
MDMegersa Olumana Dinka
Megersa Olumana Dinka
Stephen Nyende-ByakikaStephen Nyende-Byakika
Stephen Nyende-Byakika
The solubility of oxygen in a liquid is limited/restricted by the gas–liquid film that prevents gas from dissolving in wastewater. Oxygen in the biological aeration unit (BAU) is required by microorganisms to survive and eliminate organic and inorganic matter. This study developed a volumetric mass transfer coefficient (KLa) model using Artificial Neural Network (ANN) algorithm. The performance of the KLa model was evaluated using coefficient of determination (R2), mean squared error (MSE), and root mean squared error (RMSE). KLa model produced R2 (0.852), MSE (0.0006), and RMSE (0.0245) during the testing phase. Biomass concentration (22.29%), aeration period (20.55%), and temperature (19.63%) contributed the highest towards the KLa model. KLa model showed that the BAU should be operated at high temperatures (35°C), low biomass concentration (1.65 g/L), and low aeration period (1 h) instead of high airflow (30 L/min). Temperature should be included in the modelling of the BAU, to achieve optimum KLa.

26 November 2025
Verified
Conference Paper
Closed access
AOAyodeji Okubanjo
Ayodeji Okubanjo
OKOkakwu Ignatius Kema
Okakwu Ignatius Kema
ADAdekunle Olorunlowo David
Adekunle Olorunlowo David
JNJulius Musyoka Ndambuki
Julius Musyoka Ndambuki
WKWilliams Kehinde Kupolati
Williams Kehinde Kupolati
MMMpho Muloiwa
Mpho Muloiwa
Electric vehicles (EVs) are increasingly adopted as sustainable alternatives to internal combustion vehicles. However, battery health monitoring remains a critical challenge affecting vehicle safety, performance, and lifespan. This paper presents an IoB-based Battery Health Surveillance System (BHSS) that integrates smart sensors, cloud-based analytics, predictive algorithms, and feedback mechanisms for continuous battery monitoring. Quantitative evaluation is performed using Mean Absolute Error (MAE) for voltage and current, system latency for data acquisition and cloud reporting, and anomaly detection rate (%) for battery fault alerts. Comparative analysis with conventional BMS and IoT-only. BMS demonstrates superior performance in accuracy, response time, predictive capability, and scalability. The results confirm that the proposed system enhances safety, operational efficiency, and battery lifespan in EVs.

16 March 2026 in Water Practice & Technology
Verified
Journal Article
Closed access
MMMpho Muloiwa
Mpho Muloiwa
TTTsholofelo M. Tladi
Tsholofelo M. Tladi
CZCaliphs M. Zvinowanda
Caliphs M. Zvinowanda
JNJulius M. Ndambuki
Julius M. Ndambuki
In a climate-changing environment, where global wastewater temperatures are rising, rapid organic and inorganic waste removal is required, which increases wet sludge production in the biological treatment process (BTP). Rapid wet sludge volume production creates challenges, including increased wastewater viscosity, nitrous oxide production, and the presence of toxic microorganisms in the BTP. Plant operators are then required to frequently analyze wastewater to avoid wet sludge production. Therefore, this article aims to develop a wet sludge volume model using a multilayer perceptron (MLP)-artificial neural network (ANN) algorithm. The model will incorporate climate temperature changes and will assist plant managers to predict the wet sludge volume expected, for efficient operation. The results showed that the wet sludge volume was positively. correlated with temperature (r=0.219** (** only apply to the correlation values)), indicating that an increase in climate temperature affects wet sludge production. The MLPANN algorithm was able to model wet sludge volume and produced mean squared error (0.1592), root mean squared error (0.399), and R2 (0.97277) during testing. The wet volume sludge model predicted that the climate temperature increases sludge production at a rate of 0.0102. Based on the performance evaluation, the wet sludge volume model is robust and superior and can be utilized by plant managers/operators with confidence.