This paper presents an in-depth characterization of a raw industrial sludge (IS-R) and its KOH-activated biochar pyrolyzed at 750 °C (IS-KOH-B) followed by their application to remove a cationic dye from aqueous solution. Materials characterization shows that compared to the IS-R, the IS-KOH-B has improved structural, textural, and surface chemical properties. In particular, the IS-KOH-B’s BET surface area and total pore volume are about 78 and 6 times higher than those found for the IS-R, respectively. The activated biochar efficiently retained the cationic dye under wide experimental conditions. Indeed, for an initial dye concentration of 50 mg L−1, removal yields were assessed to be more than 92.5%, 93.5%, and 97.8% for a large pH range (4–10), in the presence of high contents of competing cations (3000 mg L−1 of Ca2+, Mg2+, Na+, and K+), and a low used adsorbent dose (1 g L−1), respectively. The Langmuir’s adsorption capacities were 48.5 and 65.9 mg g−1 for of IS-R and IS-KOH-B, respectively, which are higher than those reported for various adsorbents in the literature. The dye removal was found to be monolayer, spontaneous, and endothermic for both the adsorbents. Moreover, this removal process seems to be controlled by chemical reactions for IS-KOH-B whereas by both physico–chemical reactions for IS-R. This study demonstrates that the raw industrial sludge and especially its KOH-activated derived biochar could be considered as promising adsorbents for the removal of dyes from aqueous solutions.
This study investigates the synthesis, characterization, and environmental application for amoxicillin (AMX) removal in batch mode of three novel calcium-rich biochars. These biochars were produced from the co-pyrolysis of poultry manure, date palm wastes, and waste marble powder at temperatures of 700 °C (Ca-B-700), 800 °C (Ca-B-800), and 900 °C (Ca-B-900). Characterization results show that increasing the pyrolysis temperature results in improved structural, textural, and surface chemistry properties. For instance, the BET surface area of the Ca-B-900 was assessed to be 52.3 m2 g−1, which is 14.1 and 3.1 times higher than those observed for Ca-B-700 and Ca-B-800, respectively. Moreover, the Ca-B-900 shows higher AMX removal ability (56.2 mg g−1) than Ca-B-800 (46.8 mg g−1), Ca-B-700 (14.6 mg g−1), and numerous other engineered biochars. The AMX removal process by these biochars is favorable under wide experimental conditions of initial pH and AMX concentrations. Additionally, the experimental and modeling data show that the AMX adsorption process includes both physical and chemical mechanisms. This study confirms that Ca-rich biochars can perform significant removal of AMX in batch mode.
This work investigates, for the first time, the application of a modified natural magnetite material with 35% of lanthanum for phosphorus (P) recovery from synthetic and actual wastewater under both static (batch) and dynamic (continuous stirred tank reactor (CSTR)) conditions. The characterization results showed that the natural feedstock mainly comprises magnetite and kaolinite. Moreover, the lanthanum-modified magnetite (La-MM) exhibited more enhanced textural, structural, and surface chemistry properties than the natural feedstock. In particular, its surface area (82.7 m2 g−1) and total pore volume (0.160 cm3 g−1) were higher by 86.6% and 255.5%, respectively. The La-MM efficiently recovered P in batch mode under diverse experimental settings with an adsorption capacity of 50.7 mg g−1, which is significantly greater than that of various engineered materials. It also maintained high efficiency even when used for the treatment of actual wastewater, with an adsorption capacity of 47.3 mg g−1. In CSTR mode, the amount of P recovered from synthetic solutions and real wastewater decreased to 33.8 and 10.2 mg g−1, respectively, due to the limited contact time. The phosphorus recovery process involves mainly electrostatic attraction over a wide pH interval, complexation, and precipitation as lanthanum phosphates. This investigation indicates that lanthanum-modified natural feedstocks from magnetite deposits can be regarded as promising materials for P recovery from aqueous solutions.
In this research work, a natural sample from an Omani magnetite (MG) deposit was used for the synthesis of a magnetite decorated with ferrihydrite (MG-Fh), and two lanthanum (La)-modified materials at mass percentages of 5% (MG-Fh-La-5) and 15% (MG-Fh-La-15). These materials were first characterized using various analytical techniques. Then, their phosphorus (P) recovery efficacy from aqueous solutions was studied in batch mode under a wide range of experimental conditions. The characterization results show that compared to the raw feedstock, MG-Fh, MG-Fh-La-5, and especially MG-Fh-La-15 have improved structural, textural, and surface chemistry properties. Adsorption tests indicate that due to the deposition of high contents of lanthanum oxides on its surface, the MG-La-15 exhibited a large P uptake capacity (34.5 mg g−1), which is significantly superior to those determined for MG-La-5 (24.3 mg g−1), MG-Fh (12.4 mg g−1), and various engineered materials published in the literature. Moreover, these materials retain an interesting ability to recover P from real wastewater with a highest adsorbed mass of 27.3 mg g−1, observed for MG-La-15. The P recovery seems to involve both physical and chemical mechanisms, including electrostatic interactions and complexation. This research work shows that La-modified magnetite can be considered a promising and eco-friendly material for P recovery from liquid effluents.
In this study, a sustainable calcium-rich biochar was synthesized via co-pyrolysis at 800 °C of marble waste, animal manure, and lignocellulosic biomass. This biochar (MWM–B) was comprehensively characterized and then valorized for phosphorus (P) removal from real effluent and synthetic solutions in both batch and continuous stirred tank reactor (CSTR) modes. Characterization results confirm the formation and deposition of significant amounts of calcium oxides and calcium hydroxides on the biochar surface, which enhance the biochar’s surface chemistry and textural properties. In batch mode, MWM–B efficiently removes P with a removal capacity (108.4 mg g−1) that is 5.3 times higher than that observed in the CSTR system. This efficiency drop is due to the limited contact time between phosphate species and the biochar particles. Interestingly, the presence of calcium and magnesium in the continuously renewed real effluent in the CSTR system increases P removal efficiency by approximately 136% compared with synthetic solutions. A detailed analysis of MWM–B before and after P removal suggests that this process occurs mainly through precipitation as hydroxyapatite, complexation with hydroxyl functional groups, electrostatic interactions, and hydrogen bonding. This work confirms that MWM–B generated at 800 °C is an attractive material for P removal from effluents.
In this work, three biochars were synthesized from a mixture of an abundant agricultural waste (date palm fronds) and an animal biomass (chicken manure) at pyrolysis temperatures of 700 °C (B-700), 800 °C (B-800), and 900 °C (B-900), respectively. These biochars were characterized and used as electrode materials in a capacitive deionization (CDI) process to remove salts from saline water. The CDI results show that the B-700 electrode displayed the highest desalination efficiency of 10.2% with 100 ppm NaCl. Further mixing the B-700 with 10% and 20% of multi-walled carbon nanotubes (CNT) revealed an enhanced desalination performance. For instance, a biochar-20%CNT electrode achieved a salt adsorption capacity (SAC) of 11.32 mg/g at 200 ppm NaCl, which is 7.6 times higher than that of B-700 alone. The performance enhancement is attributed to carbon nanotubes acting as conductive channels between biochar particles, thereby improving electrical conductivity and electrochemical properties of the CDI electrode. Additionally, the presence of well-known hydrophilic functional groups on CNT surfaces enhances hydrophilicity, providing a highly porous surface area. The results suggest that the CDI method with biochar–CNT electrodes offers opportunities for energy-efficient, low-cost freshwater production, with significant scaling up potential for the treatment of brackish and wastewater.