We report on the surface, sub-surface (top few nanometers) and bulk properties of hydrothermally grown zinc oxide (ZnO) nanorods (NRs) prior to and after hydrogen treatment. Upon treating with atomic hydrogen (H*), upward and downward band bending is observed depending on the availability of molecular H2O within the structure of the NRs. In the absence of H2O, the H* treatment demonstrated a cleaning effect of the nanorods, leading to a 0.51 eV upward band bending. In addition, enhancement in the intensity of room temperature photoluminescence (PL) signals due to the creation of new surface defects could be observed. The defects enhanced the visible light activity of the ZnO NRs which were subsequently used to photocatalytically degrade aqueous phenol under simulated sunlight. On the contrary, in the presence of H2O, H* treatment created an electronic accumulation layer inducing downward band bending of 0.45 eV (~1/7th of the bulk ZnO band gap) along with the weakening of the defect signals as observed from room temperature photoluminescence spectra. The results suggest a plausible way of tailoring the band bending and defects of the ZnO NRs through control of H2O/H* species.

Advanced oxidation technologies (AOTs) focusing on nonthermal plasma induced by dielectric barrier discharge are adequate sources of diverse reactive oxygen species (ROS) beneficial for water and wastewater treatment. In this study, indigo, peroxytitanyl sulphate and terephthalic acid methods were used to approximate the concentrations of O₃, H₂O₂ and OH produced in a double cylindrical dielectric barrier discharge (DCDBD) plasma configuration. The effect of pH and scavengers as well as the amount of chemical probes on the generation of oxidants was investigated. The efficiency of the DCDBD reactor was further evaluated using methylene blue (MB) as model pollutant. The results demonstrated that the formation of oxidants O₃, H₂O₂ and OH in the DCDBD reactor was pH-dependent. Furthermore, the presence of scavengers such as phosphates, bicarbonates and carbonates in the solution diminished the amount of OH in the system and hence could impact upon the degree of detoxification of targeted pollutants during water and wastewater treatment. The MB simulated dye was totally decomposed into H₂O, dissolved CO₂ and simpler aqueous entities. Herein the DCDBD design is an adequate AOT that can be used worldwide for effective decontamination of water and wastewater.

The application of highly active nano catalysts in advanced oxidation processes (AOPs) improves the production of non-selective hydroxyl radicals and co-oxidants for complete remediation of polluted water. This study focused on the synthesis and characterisation of a highly active visible light C–N-co-doped TiO₂ nano catalyst that we prepared via the sol-gel method and pyrolysed at 350 °C for 105 min in an inert atmosphere to prevent combustion of carbon moieties. Then we prolonged the pyrolysis holding time to 120 and 135 min and studied the effect of these changes on the crystal structure, particle size and morphology, electronic properties and photocatalytic performance. The physico-chemical characterisation proved that alteration of pyrolysis holding time allows control of the amount of carbon in the TiO₂ catalyst causing variations in the band gap, particle size and morphology and induced changes in electronic properties. The C–N–TiO₂ nano composites were active under both visible and UV light. Their improved activity was ascribed to a low electron–hole pair recombination rate that enhanced the generation of OH· and related oxidants for total deactivation of O.II dye. This study shows that subtle differences in catalyst preparation conditions affect its physico-chemical properties and catalytic efficiency under solar and UV light.

Membrane fouling, a major challenge in desalination, is addressed in this study by investigating three different chemical cleaning protocols (A, B, and C) targeting fouled reverse osmosis (RO) membranes and microbial community composition. Cleaning protocols A and B involve different chemical treatments selected based on preliminary tests and literature review, while protocol C follows the manufacturer’s standard recommendation. Membrane morphology, foulant composition, and microbial community variability in fouled, virgin, and cleaned membranes are studied. Effective biofilm removal is observed across all protocols using scanning electron microscopy (SEM), while spectroscopic techniques highlight interactions between foulants and membranes. Importantly, a critical gap in understanding how cleaning strategies influence microbial communities on membranes is addressed. Shifts in dominant bacterial phyla (Proteobacteria, Firmicutes, and Actinobacteria) after cleaning are identified through 16S rRNA amplicon sequencing. Cleaning A showed the best results in reducing microbial counts and restoring composition similar to virgin membranes. Additionally, chemical treatment increased dominance of resistant genera such as Staphylococcus, Bacillus, Citrobacter, and Burkholderia. This study emphasizes the necessity for tailored fouling cleaning strategies for RO membranes, with Cleaning A is a promising solution, paving the way for enhanced water purification technologies.

The Barka desalination plant, commissioned in 2018, is the largest desalination plant in Oman. It has a capacity of 281 MLD with a reverse osmosis (RO) first-pass recovery rate of 46%. As part of the standard operator practice, a membrane autopsy was conducted to determine the cause of reductions in membrane performance. This study investigated fouled membranes (model No. SW30HRLE-440) from two different locations in the membrane rack. Various analytical methods were used to conduct the membrane autopsy. Field-emission scanning electron microscopy/energy-dispersive X-ray (FESEM/EDS) analyses of membrane samples showed major components of inorganic foulants. Moreover, black and salt-like crystals deposited on the membrane surface revealed significant carbon (C) components and oxygen (O), with a small amount of magnesium (Mg), chloride (Cl), sodium (Na), aluminium (Al), and calcium (Ca), respectively. A Fourier transform infrared (FTIR) analysis revealed the presence of long-chain hydrocarbons, carboxylic acids/esters, carbohydrates/polysaccharides, and inorganic foulants. Thermogravimetric analyses (TGA) of the membranes showed a high initial weight loss due to organic and inorganic fouling. X-ray photoelectron (XPS) analyses further confirmed the presence of inorganic and organic foulants on the membrane surfaces. Bacteria identification results showed the presence of Bacillus cereus and Bacillus marisflavi. This paper offers a detailed analysis of the foulants present on the reverse osmosis membrane surface and sub-surface before and after a cleaning process.

Modified transient plane source method has been applied for thermal conductivity measurements of three water-based nanofluids containing Al₂O₃, TiO₂, and graphene nanoparticles. Experiments were conducted at different temperatures and concentrations. The effects of sort of nanoparticles, concentration, and diameter of nanoparticles as well as temperature were studied by comparing the experimental results with the predictions of ten preceding models. The overall performances of these models were compared in terms of percent error. Percent errors were observed in the current study ranging from vicinity of zero up to nearly 110% that belonged to Bruggeman model in predicting the thermal conductivity ratio of graphene/water nanofluids. All ten models performed acceptably in calculating thermal conductivity ratio of Al₂O₃ nanofluids with the maximum percent error of 2.16%. Four correlations are proposed based on the experimental results of this work three of which are special to each nanofluid and the fourth one is overall. These models succeeded to predict the thermal conductivity ratio of the studied nanofluids with considerably lower percent errors which was maximum 5.19% observed in predicting the thermal conductivity ratio of graphene/water nanofluid.