Hiroki Takahashi

Dr. Hiroki Takahashi

orcid

Research Focus & Metrics

Academic Career Length

7Years (2020-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications

31 August 2022 in Coatings
Verified
Journal Article
Open access
PDF file
Michihisa FukumotoMichihisa Fukumoto
Michihisa Fukumoto
KNKano Nakajima
Kano Nakajima
HTHiroki Takahashi
Hiroki Takahashi
A hydrogen storage alloy was formed by electrodepositing La using a molten salt. La was electrodeposited using Ni as a substrate in NaCl-KCl-5.0 mol% LaF3 molten salt at electrodeposition temperatures of 750 °C and 900 °C. The electrodeposition potential was −2.25 V. The LaNi5 hydrogen storage alloy was then prepared by the electrodeposition of La and the mutual diffusion of the Ni substrate. As a result, it was clarified that La can be electrodeposited by using a molten salt. Single-phase LaNi5 was produced at 750 °C rather than at 900 °C. It became possible to uniformly form LaNi5, an intermetallic compound, on the substrate surface. The prepared hydrogen storage alloy was exposed to Ar-10%H2 to store hydrogen; at this time, hydrogen was stored by changing the sample temperature. The discharged hydrogen was measured by a gas sensor. It was clarified that the hydrogen storage and hydrogen discharge were the highest in the sample obtained by electrodepositing La for 1 h at 750 °C. LaNi5 formed by electrodeposition showed hydrogen storage properties, and this method was found to be effective even for samples with complex shapes.

7 November 2025 in Materials
Verified
Journal Article
Open access
PDF file
Dawid KutylaDawid Kutyla
Dawid Kutyla
Michihisa FukumotoMichihisa Fukumoto
Michihisa Fukumoto
HTHiroki Takahashi
Hiroki Takahashi
RTRyuu Takahashi
Ryuu Takahashi
Katarzyna SkibinskaKatarzyna Skibinska
Katarzyna Skibinska
Piotr ŻabińskiPiotr Żabiński
Piotr Żabiński
Porous Ni, Ni–Ir, and Ni–Pt electrodes were prepared on Ni substrates by molten-salt Al co-deposition followed by dealloying. SEM/EDS and XRD confirmed a Raney-type porous network with Ir or Pt present across the layer. A urea oxidation reaction (UOR) was tested in 1 M NaOH + 0.33 M urea by cyclic voltammetry and chronoamperometry at +0.40 V vs. SCE (60 min). Smooth Ni showed near-zero current. Porous Ni resulted in ~11 mA cm−2 initially and ~9 mA cm−2 after 60 min. Porous Ni–Ir started at ~7 mA cm−2 and fell to ~2 mA cm−2 within 5 min, indicating fast deactivation, likely due to Ir-oxide formation that suppresses the Ni2+/Ni3+ redox couple. Porous Ni–Pt remained at ~11 mA cm−2 over 60 min, consistent with a stable Ni–Pt effect in which Pt aids urea adsorption/activation while Ni provides the redox path for oxidation. Overall, Pt improves UOR performance, whereas Ir lowers it under these conditions.

9 August 2024 in Metals
Verified
Journal Article
Open access
PDF file
Dawid KutylaDawid Kutyla
Dawid Kutyla
Michihisa FukumotoMichihisa Fukumoto
Michihisa Fukumoto
HTHiroki Takahashi
Hiroki Takahashi
Marek WojnickiMarek Wojnicki
Marek Wojnicki
Piotr ŻabińskiPiotr Żabiński
Piotr Żabiński
The presented paper characterized the molten salt-modified Ni electrode with excellent catalytic activity towards alkaline urea electrooxidation reaction. The electrodes were modified by electrodeposition of Al from molten salt electrolytes containing NaCl-KCl-AlF3 at a temperature of 750 °C and applied potential of −1.9 V. The porous surface was obtained by anodic polarization with a potential of −0.4 V until the anodic current was equal to 0 mAcm−2. The prepared deposits’ structure, surface morphology, and composition were analyzed using scanning electron microscopy (SEM) and X-ray diffraction (XRD). Anodic polarization was applied to assess the electrocatalytic activity and elucidate the urea electrooxidation mechanism in 1 M KOH + 0.33 M urea solution. The nanocrystalline structure, fine grain size, and microcracks on the surface of the studied electrodes contributed to their notably high electrochemically active surface area (ECSA). The cyclic voltammetry in the non-Faradaic regions of the samples shows that molten salt modification can increase the double layer capacitance of bare Ni plates by around ten times, from 0.29 mFcm−2 to 2.16 mFcm−2. Polarization of the electrodes in urea-containing KOH solution with potential of +1.52 V shows a significant difference in catalytic performance. For the bare nickel sample, the registered current density from the urea electrooxidation reaction was around +1 mAcm−2, and for the molten salt-modified one, it was +38 mAcm−2, which indicates the fact that the molten salt surface treatment can be a promising tool in tailoring the electrochemical properties of materials.

5 May 2020 in Electrochemistry
Verified
Journal Article
Open access
PDF file
KOKeisuke Ohkubo
Keisuke Ohkubo
HTHiroki Takahashi
Hiroki Takahashi
EWE. P. J. Watters
E. P. J. Watters
MTMasami Taguchi
Masami Taguchi
The issue of excessive amounts of CO2 in the atmosphere has promoted the study of methods of removing it from the atmosphere. In the field of electrochemistry, electroreduction of CO2 has become an area of significant scientific interest. Our previous work has shown Pt oxide exhibits a higher CO2 electroreduction activity than Pt. In this study, the surface adsorption species on Pt and Pt oxide during electroreduction were investigated with SEIRAS to clarify the mechanisms of the superior electroreduction activity of Pt oxide. The main adsorption species during CO2 electroreduction were methanol and HCOO− on the Pt oxide, and methanol and linear-CO on the Pt. We confirmed that the CO2 electroreduction reaction proceeds via HCOO− on Pt oxide, and through CO on Pt. The CO2 electroreduction activity is significantly affected by the adsorption species because CO strongly adsorbs on the active site and inhibits subsequent reactions. The residual oxygen in the reduced Pt oxide electrode may cause the difference in adsorption species, controlling the reaction pathway. We conclude that the superior CO2 electroreduction activity of Pt oxide is due to the difference in the reaction pathway, possibly caused by residual oxygen and oxygen vacancies in the Pt oxide electrode.

26 June 2024 in Coatings
Verified
Journal Article
Open access
PDF file
Michihisa FukumotoMichihisa Fukumoto
Michihisa Fukumoto
HTHiroki Takahashi
Hiroki Takahashi
Dawid KutylaDawid Kutyla
Dawid Kutyla
Marek WojnickiMarek Wojnicki
Marek Wojnicki
Piotr ŻabińskiPiotr Żabiński
Piotr Żabiński
The goal of this research is to fabricate a novel type of highly active porous electrode material, based on stainless steel and dedicated to water electrolyzers. The main novelty of the presented work is the innovative application of the molten salts treatment, which allows the design of a highly developed porous structure, which characterizes significantly higher catalytic activity than untreated steel substrates. The equimolar mixture of NaCl and KCl with 3.5 mol% AlF3 was used as the molten salt. The surface modification procedure includes the deposition of an Al layer with application at the potential of −1.8 V and following dissolution at −0.9 V, to create a porous alloy surface. The cathodic polarization measurements of the prepared porous stainless steel electrodes were measured in a 10 mass% KOH solution. Moreover, the amount of hydrogen generated during constant voltage electrolysis with a hydrogen sensor in situ was also measured. The porous stainless steel alloy showed higher current density at lower potentials in the cathodic polarization compared to untreated stainless steel. The cathodic polarization measurements in alkaline solution showed that the porous 304 stainless steel alloy is an excellent cathode material.