The potential of hydrates formed from R141b (CH₃CCl₂F), trimethylolethane (TME), and tetra-n-butylammonium bromide/tetra-n-butylammonium chloride (TBAB/TBAC) to be used as working substances for cold storage was investigated to provide a solution for unbalanced energy grids. In this study, the characteristics of hydrate formation, crystal morphology of hydrates, and the stability of hydrate in cyclic formation under 0.1 MPa and at 5 °C were carried out. It found that the ice had a positive effect on the hydrate formation under same conditions. Upon the addition of the ice cube, the induction time of R141b, TME, and TBAB/TBAC hydrates decreased markedly, and significantly high formation rates were obtained. Under magnetic stirring, the rate at which TBAB/TBAC formed hydrates was significantly lower than that when ice was used. In microscopic experiments, it was observed that the TBAB/TBAC mixture formed hydrates with more nucleation sites and compact structures, which may increase the hydrate formation rate. In the multiple cycle formation of TBAB/TBAC hydrates, the induction time gradually decreased with the increasing number of formation cycles and finally stabilized, which indicated the potential of the TBAB/TBAC hydrates for application in cold storage owing to their good durability and short process time for heat absorption and release.

At present, many offshore oil fields are facing problems, such as pollution-induced near-well zone blockage, poor inter-well connectivity, and strong vertical heterogeneity, which lead to insufficient formation energy and low production in the middle and late stages of development. It is necessary to develop a new technology to overcome these issues. In this regard, water-injection-induced dilation technology, which was already proven to have positive effects on loose sandstone reservoirs, was controversially applied to an offshore low-permeability reservoir. To investigate whether the water-injection-induced dilation technology is suitable, experiments were conducted to analyze the dilation potential of offshore low-permeability sandstone reservoirs, namely, X-ray diffraction, laser particle size analysis, physical simulation, computed tomography scan, and electron microscope scanning experiments. The X-ray diffraction experiments showed that the samples had more than 80% non-clay mineral content and a high brittleness index, which meant more complex microfractures under water injection. Particle size analysis experiments revealed that the particle size was mainly between 10 μm and 100 μm, and thus belonged to coarse silty sand. According to the sorting grade, the sample particle size distribution was uniform and the reservoir was more prone to dilation. The true triaxial physical simulation showed that a volumetric dilation zone occurred around the wellbore, where complicated microfractures occurred. This paper provides adequate evidence and mechanisms of dilation potential for an offshore low-permeability sandstone reservoir.

The gas lift in the offshore M field will be performed with high CO₂‐content associated gas, but the change of wellbore temperature and pressure during the injection process will lead to the change of phase and physical parameters of associated gas, which has a great impact on the design of gas lift. To ensure the smooth implementation of gas lift in the offshore M field, this paper conducts a study on the physical parameters of associated gas considering the change of CO₂ phase state. We obtained the density, viscosity, compression factor, constant pressure specific heat capacity, thermal conductivity, and Joule Thomson coefficient at each temperature and pressure by Hysys calculation, and regression analysis to obtain the regression model of the physical parameters; finally, the regression model was compared with the flash experiment and Hysys calculation results. The results show that the CO₂ phase change has a large influence on the physical parameters; R² > 0.8, which indicates that the regression model has sufficient reliability; the results of the comparison show that the empirical formulas of all physical properties have sufficient accuracy and superiority except Joule–Thomson coefficients. In addition, the empirical formula of the Joule–Thomson coefficient also has good accuracy and superiority at the pressure not exceeding 22 MPa. The study of phase changes and physical parameters of associated gas with high CO₂ content provides a basis for subsequent gas lift design in the offshore M field and multiphase flow calculations in the wellbore during the gas lift. Although this study is only applicable to this sample, it also provides a feasible research method for other samples.

With the development of offshore oil fields, the reservoirs of X oilfield in the west of the South China Sea are poor in physical property, serious in pollution, and increasingly prominent in interlayer contradictions. Water injection dilation technology has strongly affected the development of loose sandstone reservoirs. To explore whether this technology applies to the low-permeability sandstone of X oilfield in the west of the South China Sea and the dilation effect and radius of water injection dilation technology on the target reservoir, low confining pressure rock mechanics experiments and numerical simulation of water injection in this reservoir section are carried out. The triaxial shear experiment of low confining pressure shows that the target reservoir sandstone with low-permeability can have a shear strength of 45 MPa when the effective confining pressure is 0.5 MPa, and the target reservoir core can have dilatancy. When the axial strain is 2.5%, the core dilatancy is 1%, and the permeability changes by 1.17 times. It was found that the core volume dilation was obviously under low effective confining pressure, and the permeability is 2 orders higher than in the initial condition. The numerical simulation of the target reservoir shows that the bottom-hole pressure reaches 47.12 MPa at the end of water injection in typical wells. The reservoir was deformed to different degrees around the well, and the top layer was raised by 5.58 mm. This paper characterizes the rock expansion potential and expansion flow capacity of low-permeability sandstone reservoirs from multiple perspectives and establishes a three-dimensional, full-size wellbore formation crustal stress strict matching geological model for offshore expansion wells. We have provided theoretical guidance for on-site construction.

Change regulation of the physical properties of fluid is key to accurately predicting multiphase fluid flow in the production wellbore of CO₂ flooding reservoirs. Given the characteristics of significant changes in pressure, temperature, and CO₂ content in the whole wellbore of production wells in CO₂ flooding reservoirs, this paper systematically studied the change rules of volume factor, viscosity, density, and solubility of well fluid for pressure 5~30 MPa, temperature 20~120 °C, and CO₂ content 10~90% through single degassing PVT experiments. According to the experimental results, the volume factor of crude oil increases first and then decreases with the pressure increase. At the bubble point pressure (20 MPa), the volume factor of crude oil can reach 1.89 at high temperatures. The volume factor can be increased from 1.28 to 1.44 at 8 MPa when the temperature increases from 20 °C to 120 °C. Under the bubble point pressure, the increase in pressure increases the solubility of CO₂, and the viscosity of crude oil decreases rapidly. In contrast, above the saturation pressure, the increase in pressure increases the viscosity of crude oil. Under the freezing point temperature (24 °C), the viscosity of crude oil decreases sharply with increase in temperature. In contrast, above the freezing point temperature, the viscosity change of crude oil is not sensitive to temperature. The wellbore temperature has a significant impact on the density of the well fluid. At 5 MPa, the temperature increases from 20 °C to 120 °C, which can reduce the density of high CO₂ crude oil from 0.93 g/cm³ to 0.86 g/cm³. The solubility of CO₂ in crude oil is sensitive to pressure. When the pressure increases from 5 MPa to 15 MPa at 20 °C, the solubility increases by 36.56 cm³/cm³. The results of this paper support the multiphase fluid flow law prediction of CO₂ flooding production wells with a high gas–liquid ratio.

Offshore oil field loose sandstone reservoirs have high permeability. However, during the water injection process, water injection blockage occurs, causing an increase in injection pressure, making it impossible to continue injecting water on site. Current research mainly focuses on the factors causing water injection blockage, with less attention given to the blockage locations and the pressure increase caused by water injection. There is a lack of research on the change in the law of injection capacity. This paper establishes a simulation experiment for water injection blockage that can accommodate both homogeneous and heterogeneous cores. The experimental core is 1 m long and capable of simulating the blockage conditions in the near-well zone during water injection, thereby analyzing the core blockage position and blockage pressure. The study clarifies the influence of water quality indicators, heterogeneity, and core length on the blockage patterns in reservoirs during water injection. The research findings are as follows: I. The reservoir blockage samples were characterized using scanning electron microscopy (SEM), casting thin sections, and X-ray diffraction (XRD) analysis. The results indicate that the main factors causing blockage are clay, silt, and fine particulate suspensions, with the fine particles mainly consisting of hydrated silicates and alkali metal oxides. The primary cause of blockage in loose sandstone is identified as the mechanism of migration and accumulation of clay, fine rock particles, and suspended matter in the injected water. II. By monitoring pressure and permeability changes in the core flooding experiments, the impact of reservoir heterogeneity on water injection capacity was evaluated. The evaluation results show that the blockage locations and lengths in heterogeneous cores are twice those in homogeneous cores. III. For heterogeneous reservoirs, if the initial permeability at the inlet is lower than in other segments of the core, significant blockage resistance occurs, with the final resistance being 1.27 times that of homogeneous cores. If the initial permeability at the inlet is higher than in other parts, the final blockage resistance is close to that of homogeneous cores. This study provides theoretical support for the analysis of blockage locations and pressures in loose sandstone water injection and offers technical support for the design of unplugging ranges and pressures after blockage in heterogeneous formations. At the same time, it provides a theoretical basis for selecting the direction of acidizing after blockage occurs in loose sandstone.