Hydrostatic bearings come with certain advantages over rolling bearings in moving large-scale structures. However, assembly errors are a serious matter on large scales. This study focuses on finding assembly error tolerances for the most common types in segmented errors of hydrostatic bearing sliders: tilt and offset. The experimental part was performed in the laboratory on a full diagnostic hydrostatic bearing testing rig. An investigation of the type of error on bearing performance was first conducted under static conditions. We identified the limiting error-to-film thickness ratio (e/h) for static offset error as 2.5 and the tilt angle as θ = 0.46° for the investigated case. Subsequently, two types of offset error were investigated under slow-speed conditions at 38 mm/s. The limiting error for the offset error considering the relative bi-directional movement of the slider and the pad was determined as e/h < 1. The results further indicate that the error tolerance would further decrease with increasing speed. The experimental results of error tolerances can be used to determine the required film thickness or vice versa.
Hydrostatic bearings are frequently used for moving large structures smoothly and precisely. In such applications, difficulties with manufacturing, transportation, and assembly arise. The safety and precision of the entire supported structure depend on the accuracy of the hydrostatic bearing alignment. There are several suitable methods for its alignment, yet it is not clear which method can achieve the highest bearing precision. This study provides a comparative experimental assessment of the three methods. The measurements were performed on a hydrostatic bearing test rig with independent positioning of the pads. Conventional measuring devices, a pressure distribution alignment method, and an optical method, OCMM (optical coordinate measuring machine), were compared. The accuracy of the selected methods and the difficulty of the aligning process were included in the comparison. The OCMM method was able to achieve an accuracy 1.6 times higher relative to the pressure method and 6 times higher compared to conventional measuring devices. This method is versatile and can be applied for a wide range of bearing sizes.
The design and real-time control of hydrostatic bearings (HS) require precise models capable of accurately predicting bearing behaviour under diverse operational conditions. Traditional analytical models have been found to be inadequate to simultaneously estimating critical parameters, including carrying capacity, recess pressure, film thickness, and flow rate. To overcome these limitations, Computational Fluid Dynamics (CFD) has emerged as a powerful tool in recent years. However, the accuracy of operational data used to calibrate the numerical and analytical models significantly influences the propagation of uncertainty. This study focusses on an experimental campaign and the development of a CFD model within the OpenFOAM® environment. Numerical and analytical models were calibrated using various input parameters, such as flow rate and recess pressure, to replicate experimental conditions while accounting for extreme operational scenarios and the inherent uncertainties in the experimental data. The results indicate that although average CFD predictions exhibit consistent errors in estimating operational parameters, the uncertainty ranges of the experimental and numerical data overlap under the conditions examined. On the contrary, analytical predictions show notable discrepancies, even when measurement uncertainties are considered. In particular, recess pressure emerged as the most effective input parameter to accurately estimating carrying capacity. These findings highlight the critical importance of incorporating measurement uncertainties into the calibration of numerical and analytical models for HS bearings, offering valuable information for their precise design and effective real-time control. Moreover, this paper demonstrates how CFD enables the consideration of misalignments measured during experimentation, a factor that is not accounted for in current analytical models.
16 June 2022 in Proceedings of the Institution of Mechanical Engineers, Part J: Journal of Engineering Tribology
Hydrostatic bearings are vital part of numerous industrial applications of various sizes. Especially large-scale bearings are often encountered with complications caused by pad alignment and levelling. For such cases, a contactless measurement method was developed for film thickness diagnostics of hydrostatic bearings. The proposed method is based on a monocular tracking method, which is versatile and easily applicable for in-field measurements and diagnostics of hydrostatic lubricating films. The optical method is compared with analytical calculation and film thickness data obtained from proximity sensors of the experimental device. The results show good agreement of the data obtained from proximity sensors and the analytical calculation compared to the optical measurement. The proposed method could be used to improve the hydrostatic bearing pad levelling, alignment, or film thickness diagnostics of hydrostatic bearing pads to avoid costly maintenance that might arise due to collision of sliding surfaces in the case of lubricating film failure.
Hydrostatic bearings are commonly used across a range of applications, yet their reliance on externally pressurized lubricants presents significant energy consumption challenges. This research aims to experimentally assess various approaches for optimizing the geometry of hydrostatic bearing pads. Utilizing a two-pad hydrostatic tester equipped with online diagnostics, we analyzed optimized multi-recess pads developed through both analytical methods and computational fluid dynamics (CFD). Our results demonstrate that the CFD method achieves a substantially greater film thickness recess pressure compared to the analytical method under similar experimental conditions. Additionally, the CFD approach reduces pumping power losses by 14%. However, this improvement in performance is accompanied by a reduction in film stiffness and an increased sensitivity to eccentric overload or misalignment, as highlighted in our findings. While the adoption of CFD-optimized geometries offers significant potential for lowering energy consumption, maintaining precise alignment especially in large-scale applications remains essential. In summary, our study suggests that employing CFD optimization can effectively reduce the service costs associated with hydrostatic bearings, but optimal outcomes necessitate careful alignment considerations.
23 December 2024 in Advanced Engineering Materials
Hydrostatic bearings are commonly used in high‐precision applications due to their excellent performance across a wide range of sizes, from millimeters to tens of meters. However, their operation is dependent on a continuous external supply. If this supply fails or the pad alignment is improper, collisions or damage to sliding surfaces can occur, compromising machine precision or even causing malfunction. This study presents an experimental assessment of selected material combinations for sliding surfaces to minimize damage in large‐scale hydrostatic bearings under critical conditions. The research aims to identify the most suitable material combinations that ensure a reliable and efficient operation of hydrostatic bearings, even in the case of oil supply failure or pad misalignment. The experimental methodology focuses on the influence of material properties on friction and wear. According to the results, the most suitable materials to combine with structural steel are tin, polytetrafluoroethylene, and leaded compositions. On the other hand, aluminum bronze, structural steel, and galvanized steel are the least suitable combinations. These findings offer valuable insights into selecting the most appropriate conformal sliding surface material combination for large‐scale hydrostatic bearings based on multiple criteria, which can contribute to improved safety and durability.