Aleksandrina Ivanova Bankova

Dr. Aleksandrina Ivanova Bankova

orcid

Research Focus & Metrics

Academic Career Length

6Years (2021-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
6 October 2022
Verified
Conference Paper
Closed access
ABAleksandrina Ivanova Bankova
Aleksandrina Ivanova Bankova
STStefan Tenev
Stefan Tenev
ZTZoya Doncheva Tsoneva
Zoya Doncheva Tsoneva
MTMomchil Tachev
Momchil Tachev
IMIsmail Mehmedov
Ismail Mehmedov
Design documentation proved to be insufficient in determining the areas of sheet metal element unfolds as well as that of machines and equipment with a predominant number of sheet metal elements. Therefore, the present study proposes an approach for determining the percentage of technological waste which can be used to increase the amount of sheet material needed in the machine detail manufacturing. Using the AutoCAD product operational characteristics, it is possible to significantly reduce a large percentage of technological waste.

25 August 2025 in Engineering Proceedings
Verified
Conference Paper
Open access
PDF file
ABAleksandrina Ivanova Bankova
Aleksandrina Ivanova Bankova
AYAnastas Yangyozov
Anastas Yangyozov
STStefan Tenev
Stefan Tenev
AAAsparuh Atanasov
Asparuh Atanasov
This report examined a design solution for a wastewater treatment facility in which—based on input data such as the amount of suspension at the inlet—the solid content in the suspension and sludge, the relative weight of the particles, the sedimentation rate, the diameter and height of the radial settler were determined. After determining the parameters, the design solution was created in the SolidWorks 2024 environment. In the design process, the shape of the fastening device was modified, which is of significant importance in the design of the facility, as it affects in a specific way the concentration of suspended substances in the thickened sludge and in the recirculated sludge flow. The design was transferred into the ANSYS CFX 2017 software for subsequent simulation of its purification function. Based on techniques in fluid mechanics, the boundary and end conditions for the analysis of the fluid flow were set. The study focused on the analysis of a CFD model to describe the movement of a two-phase fluid consisting of rainwater and sand with a particle size of 1–10 mm. Based on the analysis, the results of the influence of rotating elements on the movement of the solid phase and water in the fluid domain were reported.

1 January 2023 in AIP Conference Proceedings
Verified
Conference Paper
Open access
PDF file
ABAleksandrina Ivanova Bankova
Aleksandrina Ivanova Bankova
ZTZoya Doncheva Tsoneva
Zoya Doncheva Tsoneva
STStefan Tenev
Stefan Tenev
MTMomchil Tachev
Momchil Tachev
The present study clarifies some aspects and practical applications of non-expandable surface unfolds of second or higher order and the transition elements between different in type and shape cross-sections with variable dimensions. The aim is to optimize cutting in the process of designing parts and assemblies in the field of transport engineering. The minimization of the segment (sector) cutting line lengths of the inscribed detail expandable surfaces is compared with the cutting programming, which determines the production time of the transport systems and equipment details.

1 September 2025 in Engineering Proceedings
Verified
Conference Paper
Open access
PDF file
AAAsparuh Atanasov
Asparuh Atanasov
ABAleksandrina Ivanova Bankova
Aleksandrina Ivanova Bankova
Introduced in the present study is a novel method for measuring soil density during standard tillage operations. The methodology involves the use of a strain gauge to measure the surface tensions of the plough body stem, reflecting the resistance force in the soil, through which the calculation of the density becomes feasible. The sensor is conveniently mounted above the contact area with the soil, allowing for easy replacement as required. Due to the small forces of surface deformation in the metal, a weight sensor with a capacity of 300 grams is used. The measurement process is continuous, and all plough bodies can be equipped with sensors. The results obtained demonstrate a high level of accuracy, with a Multiple R = 0.95 and R Square = 0.90 compared to tests conducted with a standard penetrometer, confirming the effectiveness and appropriateness of the proposed method.

16 August 2024 in Engineering Proceedings
Verified
Conference Paper
Open access
PDF file
ZTZoya Doncheva Tsoneva
Zoya Doncheva Tsoneva
MTMomchil Tachev
Momchil Tachev
ABAleksandrina Ivanova Bankova
Aleksandrina Ivanova Bankova
PPPlamen Parushev
Plamen Parushev
STStefan Tenev
Stefan Tenev
PDProlet Deneva
Prolet Deneva
Preserving and restoring architectural monuments of symbolic national significance stand as an unequivocal priority for both local and state authorities. Indeed, with advancements in the technology, materials, and methods of work, there are some specific stages involved in the process of restoring historical buildings; however, maintaining their authentic form and impact poses a serious challenge, necessitating the development of innovative, non-standard technologies and the adaptation of a multifunctional methodology to achieve the desired outcome. The present study focuses on the restoration of the roof covering of the historical building of the “Dormition of the Mother of God” Cathedral in Varna, in terms of technological feasibility and cost-effectiveness. Proposed in this paper is a solution that strives to restore the magnificent roof in adherence to the heritage conservation principles by applying a genuine gold coating instead of retaining the previous dull goldish coating made from alkyd paint, yellow pigment, and gold dust. Through the implementation of descriptive geometry techniques and AutoCAD, followed by verification using Inventor, the study presents a feasible solution for accurately determining the surface area of the domes to be gilded.

23 July 2024 in Engineering Proceedings
Verified
Conference Paper
Open access
PDF file
ABAleksandrina Ivanova Bankova
Aleksandrina Ivanova Bankova
STStefan Tenev
Stefan Tenev
ZTZoya Tsoneva
Zoya Tsoneva
IMIsmail Mehmedov
Ismail Mehmedov
The primary purpose of the present research is to analyze and determine the impact that expansion and shear exert on the production time, expenditures on materials and consumable items, i.e., production costs, and the cost of the manufactured sheet material details. An applied study was, accordingly, conducted to investigate the implications of different design features and shear on a sheet material workpiece, i.e., the base of a water tower, with respect to the shear line produced during surface segmentation. In order to determine in which direction and to what extent the dimensions of the constituent elements influence the expansion, a graphical experiment was performed with a smaller width of the elements than the surrounding surface, as well as with two different steps. Cases are presented and analyzed in which the surrounding surface is considered as composed of several composite belts in horizontal and vertical arrangements of the metal sheets. The research findings refer to the sheet material parameters (thickness, dimensions), production technology principles, and their effects on the technological process to optimize material costs and reduce waste in manufacturing. The study revealed that in order to achieve optimal shear outcomes, it is recommended to manufacture all the segments concurrently, and shorten the time of production by programming the process of shear to minimize the length of the shearing lines while segmenting the surfaces of the relevant details. This will be more suitable in the case of constructions executed along helical lines, applied with a small step, where the residual material is of more compact dimensions with a suitable cut.