We propose a robot dynamic model to improve the accuracy of the identification, by introducing a friction model that takes into account the joint loads. Firstly, we analyze torque transfer in robot joints, assigning a physical meaning to motor inertia parameters. Then, we enhance the traditional friction model in identification by accounting for joint loads, presenting a new friction model with loads. Next, we employ a one-step method to directly identify both basic dynamic parameters and physical dynamic parameters of the robot. Experimental validation is conducted using a Rokea XMate3pro 7-DOF robot. Results demonstrate that our proposed dynamic model achieves higher accuracy in dynamic identification. It effectively describes the jitter phenomenon caused by motor torque when joints change the direction of motion. Furthermore, in identifying parameters for physical feasibility, our model outperforms traditional approaches by better fitting the dynamic of end joints.
27 October 2023 in IEEE Robotics and Automation Letters
This letter focuses on the design and control of a novel seven-degree-of-freedom (7-DOF) robotic manipulator (D-Arm) to address the issue of backlash nonlinearity coupling unknown disturbance through the dual-motor anti-backlash control technology. Specifically, the first three axes of the D-Arm near the base are implemented as dual-motor joints (DMJs), while the remaining four axes are single-motor joints (SMJs), which achieve a more comprehensive performance. For DMJs, as over-actuated systems, we first discover an internal disturbance phenomenon named servo-conflict and consider it in the controller design. To mitigate the adverse effects of backlash coupling disturbance, an admittance control-based position compensator is proposed. Then, after the backlash elimination, a dual-motor linear active disturbance rejection controller is effectively developed for load tracking task of the DMJ. In the presence of unknown backlash and disturbance, the proposed strategy can improve both transient and steady-state position tracking response, reduce energy consumption without requiring any backlash model information. The effectiveness and simplicity of the developed control strategy are verified through comparative experiments on the D-Arm.
Considering system uncertainties (e.g., gear backlash, unmodeled dynamics, nonlinear friction and parameters perturbation) coupling disturbances weaken the motion performance of robotic systems, an observer-based finite-time prescribed performance sliding mode control with faster reaching law is proposed for robotic manipulators equipped with dual-motor joints (DMJs). In the case where the backlash information is completely unknown, the backlash is maximally eliminated using a simple but efficient dual-motor adaptive anti-backlash strategy. Thus, the design of position tracking controllers for DMJs can be simplified. Then, to deal with the influence of disturbances and residual uncertainties (excluding backlash), a novel finite-time adaptive sliding mode disturbance observer (ASMDO) is proposed to practically estimate the lumped uncertainties where their upper bounds are assumed to be unknown. Finally, a finite-time composite fast non-singular terminal sliding mode (TSM) controller, integrated with the prescribed performance principle, is proposed in this paper. To enhance the convergence rate, a novel TSM-type reaching law has been developed. The controller ensures that the tracking error is not only stabilized within a finite-time convergence rate but also adheres to a predefined maximum transient-steady-state error. The proposed scheme is implemented through simulation and experimental results, demonstrating its superior performance.
Considering that soft airbag sensors made from soft materials are limited to detecting only normal forces, a novel PEBA–silicone composite magneto-sensitive airbag sensor is proposed for simultaneously detecting normal contact force and horizontal motion during human–robot interaction. In terms of structural design, the PEBA–silicone composite airbag is manufactured using fused deposition modeling, 3D printing, and silicone casting, achieving a balance between high airtightness and adjustable stiffness. Beneath the airbag, a magneto-sensitive substrate with several NdFeB magnets is embedded, while a fixed Hall sensor detects spatially varying magnetic fields to determine horizontal displacements without contact. The results of contact-force and motion experiments show that the proposed sensor achieves a force resolution of 20 g, a force range of 0 to 1100 g, a fitting sensitivity of 7.54 N/Pa, an average static stiffness of 4.82 N/mm, and a horizontal motion detection range of 0.125 to 1 cm/s. In addition, the prototype of the sensor is lightweight (with the complete assembly weighing 81.25 g and the sensing part weighing 56.13 g) and low-cost, giving it potential application value in exoskeletons and industrial grippers.
Monocular Gaussian SLAM must recover camera motion, surface structure, and appearance from an RGB sequence without metric depth input or benchmark geometry during reconstruction. This setting is challenged by scale-ambiguous predictions, spatially varying reliability, and the tendency of an unconstrained Gaussian map to absorb pose and depth errors into its geometric and appearance parameters. We present Mono3DGS-SLAM, a reliability-guided Gaussian–TSDF framework with a sequence-precalibrated prediction stage and an incremental mapping backend. Deterministic reliability gates select admissible observations, while one frozen scale jointly transports predicted depth, camera translation, and length-valued mapping parameters into an internally consistent canonical coordinate. A confidence-weighted colorized TSDF stores the persistent surface, base color, and visibility support. A capacity-bounded Gaussian layer is restricted to reliable residual regions and primarily restores appearance detail over the fused surface. On Replica, Mono3DGS-SLAM achieves 0.249 cm mean ATE and is most accurate in five of eight scenes. With identical poses, depths, and views, the hybrid output reaches 30.678 dB PSNR, exceeding either component alone. ScanNet and TUM-RGBD results further assess transfer to real monocular sequences.
Monocular reconstruction under severe low light is ill-posed because underexposure removes repeatable texture, view-dependent camera processing violates photometric consistency, and pose or depth errors can be absorbed as blurred or distorted Gaussian primitives. We propose LL-3DGS Reconstruction, a coupled geometric–photometric framework that estimates a canonical normally illuminated Gaussian scene while retaining raw low-light observations as explicit evidence. Its geometry front end preserves view identity and order, selects a raw or fixed enhanced stream for learned multi-view inference, and converts the estimated cameras, depth, and points into a density-aware Gaussian seed with optional Sim(3) co-registration. The Gaussian back end constrains one shared 3D field through a bounded luminance restoration path and a low-light re-degradation path, preventing independent per-view corrections from becoming inconsistent scene content. Dark-region weighting, reliability-aware supervision, staged activation, bounded densification, and scale–anisotropy constraints further regularize flexible Gaussian primitives against noise, illumination errors, and weak geometry. Finally, co-registered metric depth supplies surface geometry while the canonical Gaussian rendering supplies restored color for colored-point and TSDF fusion. With paired normal-light supervision, the method obtains 25.44 dB PSNR, 0.898 SSIM, and 0.247 LPIPS on five LOM scenes and averages 21.195 dB, 0.449 SSIM, and 0.523 LPIPS across eight LLRS scenes. A controlled LOM-sofa ablation shows that low-light consistency supports observation explainability, while four-scene TSDF outputs document the explicit reconstruction path without claiming geometric accuracy in the absence of 3D ground truth.