This letter focuses on the design and control of a novel seven-degree-of-freedom (7-DOF) robotic manipulator (D-Arm) to address the issue of backlash nonlinearity coupling unknown disturbance through the dual-motor anti-backlash control technology. Specifically, the first three axes of the D-Arm near the base are implemented as dual-motor joints (DMJs), while the remaining four axes are single-motor joints (SMJs), which achieve a more comprehensive performance. For DMJs, as over-actuated systems, we first discover an internal disturbance phenomenon named servo-conflict and consider it in the controller design. To mitigate the adverse effects of backlash coupling disturbance, an admittance control-based position compensator is proposed. Then, after the backlash elimination, a dual-motor linear active disturbance rejection controller is effectively developed for load tracking task of the DMJ. In the presence of unknown backlash and disturbance, the proposed strategy can improve both transient and steady-state position tracking response, reduce energy consumption without requiring any backlash model information. The effectiveness and simplicity of the developed control strategy are verified through comparative experiments on the D-Arm.
Considering system uncertainties (e.g., gear backlash, unmodeled dynamics, nonlinear friction and parameters perturbation) coupling disturbances weaken the motion performance of robotic systems, an observer-based finite-time prescribed performance sliding mode control with faster reaching law is proposed for robotic manipulators equipped with dual-motor joints (DMJs). In the case where the backlash information is completely unknown, the backlash is maximally eliminated using a simple but efficient dual-motor adaptive anti-backlash strategy. Thus, the design of position tracking controllers for DMJs can be simplified. Then, to deal with the influence of disturbances and residual uncertainties (excluding backlash), a novel finite-time adaptive sliding mode disturbance observer (ASMDO) is proposed to practically estimate the lumped uncertainties where their upper bounds are assumed to be unknown. Finally, a finite-time composite fast non-singular terminal sliding mode (TSM) controller, integrated with the prescribed performance principle, is proposed in this paper. To enhance the convergence rate, a novel TSM-type reaching law has been developed. The controller ensures that the tracking error is not only stabilized within a finite-time convergence rate but also adheres to a predefined maximum transient-steady-state error. The proposed scheme is implemented through simulation and experimental results, demonstrating its superior performance.
7 December 2022 in Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science
In order to provide theoretical reference for the determination of structural parameter tolerance at the initial design stage of manipulator body structure’s precision, so as to improve the geometric positioning accuracy of manipulator end-effector, a parameter tolerance optimal allocation method based on the optimal precision model is proposed. This method does not need tolerance-cost model and relevant statistical information, reaching the balance between accuracy and manufacturing cost. This study takes ROKAE XB7 6-DOF series manipulator as the research object. Based on the synthesis error of extremum model and optimal precision model, genetic algorithm is used to optimize the tolerance allocation of DH-parameters. Through the simulation analysis and experimental verification of the positioning error of the manipulator, the results show that the designed precision of the manipulator can meet the design requirements. The tolerance optimal allocation method proposed in this study can be applied to the geometric precision design of the 6-DOF series manipulator.
8 September 2023 in Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science
Due to low stiffness of compliant series robot body, the influence of joint flexible deformation caused by the gravity load of the end-effector on the absolute positioning accuracy cannot be ignored. In order to improve the flexible positioning accuracy of the robot end-effector, a calibration method for predicting and compensating the flexible positioning error of the 7-DOF series compliant robot due to the gravity load of the end-effector is proposed. The method identifies and predicts the pose configuration with similar flexible positioning error through the semi-parametric error model based on joint stiffness identification and of BP neural network. The feedforward method is used to compensate the positioning error. In this study, a 7-DOF series compliant robot is selected as the research object. Based on the principle of error similarity, the measurement points and the corresponding pose configurations are selected as the training data for the parameter identification of the semi-parametric error model, and the flexible positioning errors on the continuous trajectory of the end-effector are compensated according to the predicted values of the model. When the mass of the end-effector is 5 kg, by this method, the maximum value, mean value and mean square error of flexible positioning error on multiple straight-line trajectories on the plane are increased from 8.4779, 5.6039, and 1.8496 mm to 0.9720, 0.3079, and 0.2303 mm, respectively. It means the positioning accuracy are increased by 88.53%, 94.50%, and 87.55%, respectively, by which could observe that the precision of this robot’s end-effector was significantly improved.
Monocular reconstruction under severe low light is ill-posed because underexposure removes repeatable texture, view-dependent camera processing violates photometric consistency, and pose or depth errors can be absorbed as blurred or distorted Gaussian primitives. We propose LL-3DGS Reconstruction, a coupled geometric–photometric framework that estimates a canonical normally illuminated Gaussian scene while retaining raw low-light observations as explicit evidence. Its geometry front end preserves view identity and order, selects a raw or fixed enhanced stream for learned multi-view inference, and converts the estimated cameras, depth, and points into a density-aware Gaussian seed with optional Sim(3) co-registration. The Gaussian back end constrains one shared 3D field through a bounded luminance restoration path and a low-light re-degradation path, preventing independent per-view corrections from becoming inconsistent scene content. Dark-region weighting, reliability-aware supervision, staged activation, bounded densification, and scale–anisotropy constraints further regularize flexible Gaussian primitives against noise, illumination errors, and weak geometry. Finally, co-registered metric depth supplies surface geometry while the canonical Gaussian rendering supplies restored color for colored-point and TSDF fusion. With paired normal-light supervision, the method obtains 25.44 dB PSNR, 0.898 SSIM, and 0.247 LPIPS on five LOM scenes and averages 21.195 dB, 0.449 SSIM, and 0.523 LPIPS across eight LLRS scenes. A controlled LOM-sofa ablation shows that low-light consistency supports observation explainability, while four-scene TSDF outputs document the explicit reconstruction path without claiming geometric accuracy in the absence of 3D ground truth.
Monocular Gaussian SLAM must recover camera motion, surface structure, and appearance from an RGB sequence without metric depth input or benchmark geometry during reconstruction. This setting is challenged by scale-ambiguous predictions, spatially varying reliability, and the tendency of an unconstrained Gaussian map to absorb pose and depth errors into its geometric and appearance parameters. We present Mono3DGS-SLAM, a reliability-guided Gaussian–TSDF framework with a sequence-precalibrated prediction stage and an incremental mapping backend. Deterministic reliability gates select admissible observations, while one frozen scale jointly transports predicted depth, camera translation, and length-valued mapping parameters into an internally consistent canonical coordinate. A confidence-weighted colorized TSDF stores the persistent surface, base color, and visibility support. A capacity-bounded Gaussian layer is restricted to reliable residual regions and primarily restores appearance detail over the fused surface. On Replica, Mono3DGS-SLAM records 0.249 cm mean ATE in the evaluated runs and has lower ATE in five of eight scenes within the locally evaluated monocular group. With identical poses, depths, and views, the hybrid output reaches 30.678 dB PSNR in a paired comparison of outputs from the same hybrid runs. This comparison does not establish superiority over independently optimized single-representation systems. The evaluated full pipeline uses future observations and does not establish online or real-time SLAM performance. ScanNet and TUM-RGBD results further assess transfer to real monocular sequences.