Estuarine environments worldwide are among the most threatened habitats due to increased disturbances resulting from coastal infrastructure and rising population densities. Boating activity is a primary disturbance, as it induces biological stress and morphological changes along the coastline. This high-energy environment that boat wakes create has resulted in loss of surrounding oyster reefs and salt marsh vegetation, ultimately leading to shoreline and habitat erosion. Here, we characterize the boat wake climate in the Intracoastal Waterway, assess the bathymetry in this heavily trafficked area, and anticipate the effects of experimental living shorelines (natural breakwall and oyster restoration structures) on facilitating sediment deposition and slowing vegetation retreat. Field observations indicate that boat wakes suspend nearshore sediment and can reach heights greater than 40 cm. A numerical stability model of the breakwalls suggests that the optimal porosity is field-specific. The desired porosity for minimizing lateral displacement is 0.50, while it is 0.18 for maximum energy dissipation, which indicates a need to further investigate this complex problem. These findings demonstrate that boat wakes significantly and regularly disturb estuarine shorelines and may be altering their bathymetry as well as suggest that the design of the breakwalls may be optimized to best counteract this pervasive disturbance.
Sinkhole collapse may result in significant property damage and even loss of life. Early detection of sinkhole attributes (buried voids, raveling zones) is critical to limit the cost of remediation. One of the most promising ways to obtain subsurface imaging is 3D seismic full-waveform inversion. For demonstration, a recently developed 3D Gauss-Newton full-waveform inversion (3D GN-FWI) method is used to detect buried voids, raveling soils, and characterize variable subsurface soil/rock layering. It is based on a finite-difference solution of 3D elastic wave equations and Gauss-Newton optimization. The method is tested first on a data set constructed from the numerical simulation of a challenging synthetic model and subsequently on field data collected from two separate test sites in Florida. For the field tests, receivers and sources are placed in uniform 2D surface grids to acquire the seismic wavefields, which then are inverted to extract the 3D subsurface velocity structures. The inverted synthetic results suggest that the approach is viable for detecting voids and characterizing layering. The field seismic results reveal that the 3D waveform analysis identified a known manmade void (plastic culvert), unknown natural voids, raveling, as well as laterally variable soil/rock layering including rock pinnacles. The results are confirmed later by standard penetration tests, including depth to bedrock, two buried voids, and a raveling soil zone. Our study provides insight into the application of the 3D seismic FWI technique as a powerful tool in detecting shallow voids and other localized subsurface features.
This paper presents an application of the embedded data collector (EDC) approach using strain and acceleration measurements at the top and bottom of a pile (drilled shaft) during dynamic loading (Statnamic) for estimation of static side and tip resistance. For assessment of the skin friction, wave propagation along the pile was modeled as a one-dimensional (1D) wave equation with nonlinear static skin friction and viscous damping. The soil–pile system was divided into segments, and each segment was characterized with independent multilinear skin friction. The skin friction of each segment was determined by least-squares fitting of computed particle velocities to the measured data at the top and bottom of the pile. For assessment of the tip resistance, the pile tip was modeled as a single—degree-of-freedom nonlinear system. A nonlinear stiffness–displacement relationship was determined by balancing force and energy from inertia, damping, and stiffness against the measured tip data. The technique wa...
South Florida has multiple limestone (carbonate-rocks) formations formed during the Pleistocene Epoch near the ground surface. The FDOT is considering their use to support shallow foundations beneath bridge piers or bents. Required for design is assessment of the rocks’ bearing capacity which requires a strength envelope for the rock, as well as identifying their stress-strain response, for identifying failure modes (general, local, and punching). Using Brazilian splitting tension and a Hoek triaxial compression cell (Hoek and Franklin 1968), various confining pressures and volumetric measurements were obtained for multiple rock formations in south Florida. Based on the triaxial measurements, the limestone samples transition from brittle behavior at lower confining pressures (50 kPa or 7 psi) to ductile response at higher confining pressures (1,400 kPa or 200 psi). Also based on triaxial testing, the south Florida formations exhibited volumetric contraction during shear. Influencing the response were several index measurements: dry densities, outer and inner porosities as well as chemical carbonate content of the rock, which are specific to each formation (e.g., Miami, Fort Thompson, Anastasia, and Key Largo).