A 6-year-old castrated male mixed dog presented with a rapidly growing mass at the right chest wall two weeks after initial detection. A mesenchymal origin of the malignancy was suspected based on fine-needle aspiration. Computed tomography (CT) revealed that the mass originated from the right chest wall and protruded externally (6.74 × 5.51 × 4.13 cm3) and internally (1.82 × 1.69 × 1.50 cm3). The patient revisited the hospital because of breathing difficulties. Radiography confirmed pleural effusion, and ultrasonography-guided thoracocentesis was performed. The effusion was hemorrhagic, and microscopic evaluation showed no malignant cells. Before surgery, CT without anesthesia was performed to evaluate the status of the patient. The 7–10th ribs were en bloc resected at a 3-cm margin dorsally and ventrally, and two ribs cranially and caudally from the mass. After recovering the collapsed right middle lobe of the lung due to compression from the internal mass with positive-pressure ventilation, a 3D-printed bone model contoured titanium mesh was tied to each covering rib and surrounding muscles using 2-0 blue nylon and closed routinely. The thoracic cavity was successfully reconstructed, and no flail chest was observed. The patient was histo-pathologically diagnosed with extraskeletal osteosarcoma. A CT scan performed 8 months after surgery showed no evident recurrence, metastasis, or implant failure. This is the first case report of chest wall reconstruction using titanium mesh in a dog. The use of a titanium mesh allows for the reconstruction of extensive chest wall defects, regardless of location, without major postoperative complications.
A 3D-printed guide is an effective method for accurately placing pedicle screws in dog vertebrae. While a conventional drill guide allows precise pilot hole formation, it can lead to potential screw wobbling during insertion. In this study, we applied a technique that assists with both drilling and screw insertion, and we compared the accuracy of screw placement using this approach with that achieved by the conventional drill guide. The screws were divided into three groups: Group A (drill guide), Group B (cannulated guide), and Group C (screw guide). The accuracy of screw placement was assessed by comparing preoperative and postoperative CT images. Group A exhibited the largest angular deviation. Group C exhibited significantly smaller deviations in entry point, exit point, angle α, and angular deviation than Group A. In Group B, only the exit-point deviation was significantly smaller than that in Group A. Furthermore, the angular deviation in Group C was significantly smaller than that in Group B. In conclusion, 3D-printed screw-guiding techniques improved the accuracy of pedicle screw placement, with screw guides outperforming cannulated guides, making them a viable option for small breed dogs.
A seven-month-old male Pomeranian presented with left forelimb lameness after a fall. Radiographic assessment confirmed proximal radial head and ulnar comminuted fracture. The initial surgical intervention involved the use of hybrid external skeletal fixation (ESF) to stabilize the radial head, concomitant with the application of a composite of bone morphogenetic protein type 2 (BMP-2)-loaded hydroxyapatite and gelatin microparticles at the fracture site. Although successful radial head healing was achieved, the ESF pinholes caused a defect in the proximal ulnar diaphysis. Subsequently, the ESF was removed, and a locking plate was applied in conjunction with the BMP-2-loaded collagen membrane to correct the radius defect. Clinical follow-up at 4.8 years postoperatively revealed a mildly decreased range of motion of the affected elbow joint, but no clinical symptoms such as lameness. Radiography revealed minimal degenerative changes and a radioulnar synostosis. Computed tomography revealed differences in the leg length and bone density. Gait analysis revealed that the left forelimb had a significant improvement in weight-bearing capacity based on weight distribution–peak vertical force metrics, compared with the right forelimb. Based on clinical outcomes, the combined application of hybrid ESF and bone tissue engineering techniques can be considered a feasible alternative treatment for radial head fractures.
This study evaluated fracture risk associated with varying trochlear groove depth-to-patellar thickness (D/T) ratios in toy and small-breed dogs using finite element analysis and cadaveric mechanical testing. Finite element models derived from computed tomography data of a 4.5-kg toy poodle were adjusted to simulate D/T ratios ranging from 0.5 to 2.0 and analyzed for von Mises stress, principal strain, safety factor, and fatigue life under standing, trotting, and jumping conditions. Increasing D/T ratios led to progressive rises in stress and compressive strain, with the safety factor falling below 1.0 during jumping at ratios of 1.0 or higher. Fatigue life declined sharply beyond a ratio of 1.25 and reached zero-cycle failure at 2.0. Complementary mechanical testing of six distal femurs (6.42–8.7 kg), surgically modified to D/T ratios of 0.5, 1.0, or 1.5, revealed fracture patterns consistent with finite element predictions. These findings suggest that excessive trochlear deepening may compromise femoral integrity and elevate fracture risk, particularly under cyclic loading. Maintaining a D/T ratio between 0.75 and 1.0 may provide an optimal balance between effective patellar tracking and mechanical safety.