This study offers a comprehensive summary of the current states as well as potential future directions of transparent conducting oxides (TCOs), particularly tin-doped indium oxide (ITO), the most readily accessible TCO on the market. Solar cells, flat panel displays (FPDs), liquid crystal displays (LCDs), antireflection (AR) coatings for airbus windows, photovoltaic and optoelectronic devices, transparent p–n junction diodes, etc. are a few of the best uses for this material. Other conductive metals that show a lot of promise as substitutes for traditional conductive materials include copper, zinc oxide, aluminum, silver, gold, and tin. These metals are also utilized in AR coatings. The optimal deposition techniques for creating ITO films under the current conditions have been determined to be DC (direct current) and RF (radio frequency) MS (magnetron sputtering) deposition, both with and without the introduction of Ar gas. When producing most types of AR coatings, it is necessary to obtain thicknesses of at least 100 nm and minimum resistivities on the order of 10−4 Ω cm. For AR coatings, issues related to less-conductive materials than ITO have been considered.
Thin conducting films are distinct from bulk materials and have become prevalent over the past decades as they possess unique physical, electrical, optical, and mechanical characteristics. Comprehending these essential properties for developing novel materials with tailored features for various applications is very important. Research on these conductive thin films provides us insights into the fundamental principles, behavior at different dimensions, interface phenomena, etc. This study comprehensively analyzes the intricacies of numerous commonly used thin conducting films, covering from the fundamentals to their advanced preparation methods. Moreover, the article discusses the impact of different parameters on those thin conducting films’ electronic and optical properties. Finally, the recent future trends along with challenges are also highlighted to address the direction the field is heading towards. It is imperative to review the study to gain insight into the future development and advancing materials science, thus extending innovation and addressing vital challenges in diverse technological domains.
The research on two-dimensional materials has gained significant traction due to their potential for thermoelectric, optical, and other properties. The development of two-dimensional (2D) nanostructured-based TE generators and photodetectors has shown promising results. Over the years, researchers have played a crucial role in advancing this field, enhancing the properties of 2D materials through techniques such as doping, alloying, and various growth methods. Among these materials, black phosphorus, transition metal dichalcogenides, graphene, and IVA-VIA compounds stand out for their remarkable electronic, mechanical, and optical properties. This study presents a comprehensive review of the progress in the field, focusing on IVA-VIA compounds and their applications in TE and photodetector technologies. We summarize recent advancements in enhancing these materials’ TE and optical properties and provide an overview of various synthesis techniques for their fabrication. Additionally, we highlight their potential applications as photodetectors in the infrared spectrum. This comprehensive review aims to equip researchers with a deep understanding of the TE and optical properties of 2DMs and their potential applications and to inspire further advancements in this field of research.
29 November 2023 in Malaysian Journal on Composites Science and Manufacturing
In this study,three samples were created using gravity die casting, i.e.,two modelsof immiscible alloys, Alloy1 (Al-12wt.%Sn-8wt.%Cu) and Alloy2 (Al-20wt.%Sn-10wt.%Cu),along with a control sample of pure Al.These gravity die-cast samples,homogenized at 700°Cfor 2hours,are analyzed formechanical properties and microstructures.Optical microscopy and scanning electron microscopy with energy dispersive spectroscopy (EDS) were used to analyze the changes in the Al-Sn-Cu solidified system resulting from the addition of specific alloying elements. Both Alloy1 and Alloy2 showed better mechanical properties than the control sample of pure Al. The tensile strength of Alloy2 shows a decrease from 110.878 MPato 105.750 MPacompared to Alloy1. However, there isan increase in the yield strength from 30.239 MPa to 32.362 MPa when the addition of tin exceeds 12% and copper exceeds 8%, respectively, which might be because of the alpha-phase solid solution’s interdendritic region that produces lattice strains.The impact resistance and ductility of the alloy are compromised as the hardness increases with the addition of more alloying elements. Alloy2 exhibited the highest hardness at 50.92 HB. The Brinell hardness values suggest these alloys arepotential candidatesto replace antifriction bronzes. However, hard CuAl2 is produced at the grain boundaries when copper percentages are increased, reducingthe impact properties. The effects of different alloying constituents and melt treatment on the microstructural control of Al-Sn-Cu solidified alloy werealso studied. The aluminum matrix with a semi-continuous network (reticular) distribution of tin on the grain boundary was observed. The grain size gradually decreased from 19.65 μm to 16.94 μm and became more equiaxed for Al-20wt.%Sn-10wt.%Cu than Al-12wt.%Sn-8wt.%Cu. The bond between tin and matrix improved with the increasing alloying element. The data obtained from this experiment will undoubtedly contribute to future research in this field