For a broad range of industrial, service, and household electric vehicles, dynamic charging is a viable option for energy replenishing that could reduce the size of the onboard energy storage, remove range limitations, and increase operating time. For those systems, timely detection of an approaching vehicle and the detection of strong coupling conditions between transmitter and receiver coils are of prime interest. A novel method is proposed in this article, which utilizes the existing embedded primary coil and power electronics modules to establish a precise detection system based on the power footprint of a traveling receiver. Next, a control algorithm is proposed to accurately control charger activation and deactivation time and deliver the required amount of energy during the coils maximum coupling. The proposed sigmoid-curve-based control algorithm achieves a robust, speed-independent, smooth transition between two states while providing fast dynamics for both aligned and misaligned conditions. Finally, a novel approach to test high-speed dynamic charging in laboratory conditions based on the receiver emulator is developed and used for experimental validation. The vehicle detection and control techniques have been validated through simulations and experimentally on a speed-controlled dynamic charging test station for a wide speed range. The proposed method does not require any additional hardware, sensing devices, or high-speed communication between the vehicle and the charging infrastructure.
27 March 2023 in IEEE Transactions on Transportation Electrification
Numerous articles have been written regarding the potential affects that electric vehicle (EV) charging stations can have on power distribution systems. With the advent to adopt a dynamic wireless power transfer (DWPT) roadway charging infrastructure, there lies a potential for hazardous effects to occur. Therefore, this paper presents a novel methodology to analyze the sustainability and the potential effects that a DWPT roadway can have on electric power distribution grid. Historical traffic flow (HTF) data is converted using a Monte Carlo method to develop an EV traffic flow (EV-TF). Then, a full DWPT simulation of a 1-mile and 10-mile roadway is performed to determine the power fluctuations that can occur as different densities of EVs traverse the roadway. This method creates simulations using an IEEE 33-Bus power distribution system to evaluate if a DWPT roadway for in-motion EV charging causes voltage magnitudes to fluctuate beyond operational standards.
3 March 2023 in IEEE Transactions on Power Electronics
Energy storage systems using the electric vehicle (EV) retired batteries have significant socio-economic and environmental benefits and can facilitate the progress toward net-zero carbon emissions. Based on the patented active battery control ideas, this article proposed new available power and energy analysis for battery energy storage systems (BESS) using active life balancing control techniques. It demonstrated the effectiveness of active life balancing control in extending the life of the BESS using EV-retired batteries. The analysis and design presented in this article have been validated through experimental data using batteries retired from Nissan Leaf.
31 August 2023 in IEEE Journal of Emerging and Selected Topics in Power Electronics
This paper introduces a single-stage grid-tied ac-dc conversion system designed for wireless charging applications. The proposed system employs a T-type converter to process soft dc-link voltages that are generated by a 3-ϕ Unfolder. To achieve multiple control-related tasks simultaneously, such as input power factor correction and output power regulation, a modulation scheme is presented for the high-frequency T-type converter. The T-type converter-based soft-dc to dc system is modeled using the phasor transformation technique, and closed-loop control analysis is performed to effectively regulate the battery current. Additionally, in order to facilitate power level scalability, a modular architecture is proposed, and a board with dimensions of 26.2 in (L) × 13.2 in (W) × 4.5 in (H), including the cold plate, is designed to house three T-type converters, each rated for 21 kW of output power. Hardware results of a 21 kW prototype are presented, based on a single T-type module. The prototype demonstrates an ac-dc efficiency from the grid to the battery of ~96%, and a grid current total harmonic distortion of 1.27%. To demonstrate the modular structure for multiple T-type converters operated in tandem, six T-type converter modules are tested in parallel, and corresponding hardware results are presented as well.
Traditional in-motion (dynamic) wireless power transfer (WPT) is based on elongated power transmitting tracks. It suffers from low efficiency, having complex and not fully utilized magnetic structures, among other drawbacks. In the case of lumped transmitter coils commeasurable in size with the receiver coil, which has been recently proposed for the in-motion WPT, the power transfer is intermittent with variable power transfer efficiency. Although it is characterized by a very high efficiency when the pads are aligned (>90%), high efficiency of the overall energy transfer will be maintained only if the transmitter coil is energized in a proper, synchronized manner with respect to the position of the receiver coil. Considering the actual state of communication and sensing technology, identification of the actual position of the receiver pad in realtime would be a very challenging task and no reliable solution has been proposed so far in the WPT arena. This paper provides a thorough analysis of the power transfer characteristics of an in-motion system with lumped coils, meaning the analytic description of time-varying power transfer and efficiency profiles. Possible compensation topologies are studied and the most suitable structure is selected. A control algorithm is proposed to control the amount of energy transferred to the receiver, without the utilization of any position detection system. The energizing profiles are designed to maximize energy efficiency, while at the same time transferring the required amount of energy to the receiver. The control algorithm is analyzed by using analytical modeling of the WPT system and then verified by MATLAB-Simulink simulation tool. A scaled-down hardware prototype is developed and employed to test the operation of the control algorithm for different transferred energies.