27 March 2023 in IEEE Transactions on Transportation Electrification
Numerous articles have been written regarding the potential affects that electric vehicle (EV) charging stations can have on power distribution systems. With the advent to adopt a dynamic wireless power transfer (DWPT) roadway charging infrastructure, there lies a potential for hazardous effects to occur. Therefore, this paper presents a novel methodology to analyze the sustainability and the potential effects that a DWPT roadway can have on electric power distribution grid. Historical traffic flow (HTF) data is converted using a Monte Carlo method to develop an EV traffic flow (EV-TF). Then, a full DWPT simulation of a 1-mile and 10-mile roadway is performed to determine the power fluctuations that can occur as different densities of EVs traverse the roadway. This method creates simulations using an IEEE 33-Bus power distribution system to evaluate if a DWPT roadway for in-motion EV charging causes voltage magnitudes to fluctuate beyond operational standards.
3 March 2023 in IEEE Transactions on Power Electronics
Energy storage systems using the electric vehicle (EV) retired batteries have significant socio-economic and environmental benefits and can facilitate the progress toward net-zero carbon emissions. Based on the patented active battery control ideas, this article proposed new available power and energy analysis for battery energy storage systems (BESS) using active life balancing control techniques. It demonstrated the effectiveness of active life balancing control in extending the life of the BESS using EV-retired batteries. The analysis and design presented in this article have been validated through experimental data using batteries retired from Nissan Leaf.
19 January 2022 in IEEE Transactions on Power Electronics
This article presents a new state-of-charge (SOC) balancing method with parallel and series output connected battery power modules (BPMs) in an active battery management system (BMS.) To increase both the battery pack and system-level modularity, the BMS controls the average SOC of the entire battery pack by regulating the input currents of all BPMs to a common reference. A balancing loop introduces input current offsets to regulate all cells SOCs. The BMS functions are distributed between a central controller for battery pack SOC regulation, and a module controller that regulates the input current of the individual BPMs. Experimental results are presented on a 1.5 kWh 1C-rate prototype with five series output connected battery bricks. Each battery brick consists of three parallel output connected BPMs, which employ three battery cells and three 100 W dc/dc converters.
31 August 2023 in IEEE Journal of Emerging and Selected Topics in Power Electronics
This paper introduces a single-stage grid-tied ac-dc conversion system designed for wireless charging applications. The proposed system employs a T-type converter to process soft dc-link voltages that are generated by a 3-ϕ Unfolder. To achieve multiple control-related tasks simultaneously, such as input power factor correction and output power regulation, a modulation scheme is presented for the high-frequency T-type converter. The T-type converter-based soft-dc to dc system is modeled using the phasor transformation technique, and closed-loop control analysis is performed to effectively regulate the battery current. Additionally, in order to facilitate power level scalability, a modular architecture is proposed, and a board with dimensions of 26.2 in (L) × 13.2 in (W) × 4.5 in (H), including the cold plate, is designed to house three T-type converters, each rated for 21 kW of output power. Hardware results of a 21 kW prototype are presented, based on a single T-type module. The prototype demonstrates an ac-dc efficiency from the grid to the battery of ~96%, and a grid current total harmonic distortion of 1.27%. To demonstrate the modular structure for multiple T-type converters operated in tandem, six T-type converter modules are tested in parallel, and corresponding hardware results are presented as well.
11 March 2019 in IEEE Transactions on Industry Applications
This paper presents design of an isolated high-step-down DC-DC converter based on a class-DE power stage, operating at a 10 MHz switching frequency using enhancement mode Gallium Nitride (GaN) transistors. The converter operating principles are discussed, and the power stage design rated for 20 W is presented for a step-down from 200-300 V to 0-28 V. Commercially available magnetic materials were explored and the high-frequency (HF) resonant inductor and transformer designs using a low-loss Fair-Rite type 67 material are presented. Finite element simulations have been performed to estimate the parameters of magnetics at 10 MHz. Experimental results are presented at 12 W, 254 V to 22 V and 5 W, 254 V to 14 V on a laboratory prototype operating at 10 MHz. At 20 W the experimental prototype achieved an efficiency of 85.2%.