Current research on Unmanned Aerial Vehicles (UAVs) shows a lot of interest in autonomous UAV navigation. This interest is mainly driven by the necessity to meet the rules and restrictions for small UAV flights that are issued by various international and national legal organizations. In order to lower these restrictions, new levels of automation and flight safety must be reached. In this paper, a new method for ground obstacle avoidance derived by using UAV navigation based on the Dubins paths algorithm is presented. The accuracy of the proposed method has been tested, and research results have been obtained by using Software-in-the-Loop (SITL) simulation and real UAV flights, with the measurements done with a low cost Global Navigation Satellite System (GNSS) sensor. All tests were carried out in a three-dimensional space, but the height accuracy was not assessed. The GNSS navigation data for the ground obstacle avoidance algorithm is evaluated statistically.
Fused filament fabrication, also known as fused deposition modeling and 3D printing, is the most common additive manufacturing technology due to its cost-effectiveness and customization flexibility compared to existing alternatives. It may revolutionize unmanned aerial vehicle (UAV) design and fabrication. Therefore, this study hypothesizes the 3D printing possibility of UAV using a simple desktop printer and polymeric material. The extensive literature analysis identified the acceptable prototyping object and polymeric material. Thus, the research focuses on applying polylactic acid (PLA) in manufacturing the flying wing-type UAV and develops a fabrication concept to replicate arial vehicles initially produced from a mixture of expanded polystyrene and polyethylene. The material choice stems from PLA’s non-toxicity, ease of fabrication, and cost-effectiveness. Alongside ordinary PLA, this study includes lightweight PLA to investigate the mechanical performance of this advanced material, which changes its density depending on the printing temperature. This proof-of-concept study explores the mechanical properties of printed parts of the wing prototype. It also considers the possibility of fragmentation in fabricated objects because of the limitations of printing space. The simplified bending tests identified significant reserves in the mechanical performance regarding the theoretical resistance of the material in the wing prototype, which proves the raised hypothesis and delivers the object for further optimization. Focusing on the mechanical resistance, this study ignored rheology and durability issues, which require additional investigations. Fabricating the wing of the exact geometry reveals acceptable precision of the 3D printing processes but highlights the problematic technology issues requiring further resolution.
Fused filament fabrication is the most common additive manufacturing technology due to its cost-effectiveness and flexibility in customization compared to alternative production techniques. This technology holds significant promise for revolutionizing the design and fabrication of unmanned aerial vehicles (UAVs), also known as drones. The present study continues a research program dedicated to additive drone manufacturing using a simple desktop printer and polymeric materials. The previous investigation in the series determined polylactic acid (PLA) as a potential material for drone fabrication. This research continuation takes a step forward in automating the manufacture of drones, extending the 3D printing concept to producing conductive pathways suitable for electric equipment. The automation reduces the need for manual wire installation in electric equipment. The drone prototype developed in this study demonstrates the feasibility of such automated manufacturing. The analysis of conductive polymeric materials available on the market defines the electrical resistance parameters of additively manufactured UAV components that limit the efficient electric current. The conductivity analysis of the 3D-printed components also determines the materials’ characteristics required to achieve the automated manufacturing goals of the electrically conductive pathways.
16 August 2013 in The International Archives of the Photogrammetry, Remote Sensing and Spatial Information Sciences
Implementation of Unmanned Aerial Vehicles for civilian applications is rapidly increasing. Technologies which were expensive and available only for military use have recently spread on civilian market. There is a vast number of low cost open source components and systems for implementation on UAVs available. Using of low cost hobby and open source components ensures considerable decrease of UAV price, though in some cases compromising its reliability. In Space Science and Technology Institute (SSTI) in collaboration with Vilnius Gediminas Technical University (VGTU) researches have been performed in field of constructing and implementation of small UAVs composed of low cost open source components (and own developments). Most obvious and simple implementation of such UAVs – orthophoto imaging with data download and processing after the flight. The construction, implementation of UAVs, flight experience, data processing and data implementation will be further covered in the paper and presentation.
This study addresses the optimization of aircraft maintenance task allocation for small fleets using Mixed-Integer Linear Programming (MILP). The research integrates manpower efficiency, regulatory compliance, and workload balancing to minimize downtime and enhance resource utilization. A mathematical model is formulated to account for task durations, skill levels, and sequential/parallel task constraints, validated via MATLAB implementation. Results from a simulated 50-hour Cessna 172 maintenance check demonstrate a 25% reduction in completion time compared to average manual scheduling. The model balances workloads by assigning tasks based on manpower expertise, highlighting the critical role of human factors in reducing errors and improving efficiency. Practical implications include a cost-effective alternative to commercial software for small operators, enabling optimized planning without high-cost tools. This work bridges a gap in maintenance literature by explicitly incorporating manpower efficiency into MILP frameworks, offering actionable insights for regulators and operators to avoid maintenance congestions and enhance operational resilience.
This study investigates the potential of low-density polymeric materials to enhance the deformation energy absorption of drone fuselage components manufactured using fused filament fabrication (FFF). Two materials—PLA (polylactic acid) and LW-PLA (lightweight polylactic acid)—were selected based on their accessibility, printability, and prior mechanical characterizations. While PLA is widely used in additive manufacturing, its brittleness limits its suitability for components subjected to accidental or impact loads. In contrast, LW-PLA exhibits greater ductility and energy absorption, making it a promising alternative where weight reduction is critical and structural redundancy is available. To evaluate the structural efficiency, a simplified analysis scenario was developed using a theoretical 300 J collision energy, not as a design condition, but as a comparative benchmark for assessing the performance of various metastructural configurations. The experimental results demonstrate that a stiffening core of the LW-PLA metastructure can reduce the component weight by over 60% while maintaining or improving the deformation energy absorption. Modified prototypes with hybrid internal structures demonstrated stable performances under repeated loading; however, the tests also revealed a buckling-like failure of the internal core in specific configurations, highlighting the need for core stabilization within metastructures to ensure reliable energy dissipation.