Additive manufacturing (AM) is a rapidly growing technology, referring to a 3D design process by which digital data builds a physical object in layers by depositing the printed material. The AM has evolved in the aviation, automotive, and medical industries. The AM development for fiber-reinforced composites is the point of current interest, with most research focused on using short fibers. However, notwithstanding particular technological complexities, continuous filaments have superior tensile properties compared to short fibers. Therefore, this manuscript develops an adaptive continuous reinforcement approach for AM based on polymeric material extrusion (ME) technology. It combines the raw material production process, including the ability to vary constituents (e.g., filament materials, reinforcement percentage, and recycled plastic replacement ratio), and the reinforcement efficiency analysis regarding the experimentally verified numerical model. The literature review has identified compatible materials for ensuring sustainable and high-performance plastic composites reinforced with continuous fibers. In addition, it identified the applicability of recycled polymers in developing ME processes. Thus, the study includes an experimental program to investigate the mechanical performance of 3D printed samples (polylactic acid, PLA, matrix reinforced with continuous aramid filament) through a tensile test. Recycled polymer replaced 40% of the virgin PLA. The test results do not demonstrate the recycled polymer’s negative effect on the mechanical performance of the printed samples. Moreover, the recycled material reduced the PLA cost by almost twice. However, together with the potential efficiency of the developed adaptive manufacturing technology, the mechanical characteristics of the printed material revealed room for printing technology improvement, including the aligned reinforcement distribution in the printed product and printing parameters’ setup.
Fused filament fabrication, also known as fused deposition modeling and 3D printing, is the most common additive manufacturing technology due to its cost-effectiveness and customization flexibility compared to existing alternatives. It may revolutionize unmanned aerial vehicle (UAV) design and fabrication. Therefore, this study hypothesizes the 3D printing possibility of UAV using a simple desktop printer and polymeric material. The extensive literature analysis identified the acceptable prototyping object and polymeric material. Thus, the research focuses on applying polylactic acid (PLA) in manufacturing the flying wing-type UAV and develops a fabrication concept to replicate arial vehicles initially produced from a mixture of expanded polystyrene and polyethylene. The material choice stems from PLA’s non-toxicity, ease of fabrication, and cost-effectiveness. Alongside ordinary PLA, this study includes lightweight PLA to investigate the mechanical performance of this advanced material, which changes its density depending on the printing temperature. This proof-of-concept study explores the mechanical properties of printed parts of the wing prototype. It also considers the possibility of fragmentation in fabricated objects because of the limitations of printing space. The simplified bending tests identified significant reserves in the mechanical performance regarding the theoretical resistance of the material in the wing prototype, which proves the raised hypothesis and delivers the object for further optimization. Focusing on the mechanical resistance, this study ignored rheology and durability issues, which require additional investigations. Fabricating the wing of the exact geometry reveals acceptable precision of the 3D printing processes but highlights the problematic technology issues requiring further resolution.
Advanced materials have been created for structural application during the past decades. Engineers, however, faced severe problems due to the absence of a reliable technique for ensuring the required structural properties minimising the amount of material used. A lack of constitutive models for the analysis of the structural systems also exists. Residual stiffness of flexural concrete elements subjected to short-term load is the focus of this research. Tension-stiffening models were developed to represent the deformation response of the members reinforced with internal bars. This study examines the suitability of the tension-stiffening modelling approach for simulating the deformation behaviour of the composite specimens comprising glass fibre-reinforced polymer (GFRP) pultruded profile adhesively bonded to the tensile surface of the concrete beam. The study employs a nonlinear finite element approach and analytical model to simulate the deformation behaviour of the flexural elements.
The use of high-strength steel (HSS) is a current trend of the construction industry. Tubular profiles are widely used in various structural applications because of their high stiffness-to-weight ratio, exceptional resistance to torsion, and aesthetic appearance. However, the increase of the strength for the same elastic modulus of the material and geometry of tubular profiles is often not proportional to the rise of the load-bearing capacity of the structural element. The obtained experimental results support the above inference. The study was based on the flexural test results of two groups of HSS and normal-strength steel (NSS) tubular specimens with a 100 × 100 × 4 mm (height × width × thickness) cross-section. Numerical (finite element) simulation results demonstrated that the shape of the cross-section influenced the efficiency of utilisation of HSS. The relationship between the relative increase of the load-bearing capacity of the beam specimen and the corresponding change of the steel strength determined the utilisation efficiency.
Current technology development ensures a variety of advanced materials and options for reinforcing concrete structures. However, the absence of a uniform testing methodology complicates the quantification and comparative analysis of the mechanical performance of the composite systems. The repeated mechanical loads further complicate the issue. This research extends the recently developed residual stiffness assessment concept to the repeated loading case. It provides an engineer with a simplified testing layout and analytical model to quantify the residual flexural stiffness of standardized laboratory specimens subjected to repeated cycling loads. This model explicitly relates the particular moment and curvature values, requiring neither iterative calculations nor the load history. Thus, this feature allows residual stiffness quantification under repeated loading conditions, including complete reloading of the beam samples imitating the structural strengthening procedure; the proposed technique is equally efficient in quantifying the residual stiffness of the beam samples with any combinations of fiber-reinforced polymer (FRP) reinforcements, i.e., embedded bars, near-surface-mounted strips, and externally bonded sheets. This study employs 12 flexural elements with various reinforcement and loading layouts to illustrate the proposed methodology’s efficiency in quantifying the residual strength of the tension concrete, which estimates the efficiency of the reinforcement system. The explicit quantifying of the residual resistance of the FRP reinforcement systems under repeated load cycles describes the essential novelty of this work.