Fiber-optic biosensors have garnered significant attention and witnessed rapid development in recent years owing to their remarkable attributes such as high sensitivity, immunity to electromagnetic interference, and real-time monitoring. They have emerged as a potential tool in the realm of biomarker detection for low-concentration and small molecules. In this paper, a portable and cost-effective optical fiber biosensor based on surface plasmon resonance for the early detection of breast cancer is demonstrated. By utilizing the aptamer human epidermal growth factor receptor 2 (HER2) as a specific biomarker for breast cancer, the presence of the HER2 protein can be detected through an antigen-antibody binding technique. The detection method was accomplished by modifying a layer of HER2 aptamer on the flat surface of a gold-coated D-shaped polymer optical fiber (core/cladding diameter 120/490 μm), of which the residual thickness after side-polishing was about 245 μm, the thickness of the coated gold layer was 50 nm, and the initial wavelength in pure water was around 1200 nm. For low-concentration detection of the HER2 protein, the device exhibited a wavelength shift of ~1.37 nm with a concentration of 1 μg/mL (e.g., 5.5 nM), which corresponded to a limit of detection of ~5.28 nM. Notably, the response time of the biosensor was measured to be as fast as 5 s. The proposed biosensor exhibits the potential for early detection of HER2 protein in initial cancer serum and offers a pathway to early prevention of breast cancer.

Long-range vibration sensing is an important tool for real-time structural health monitoring. A new, to the best of our knowledge, design of a distributed fiber-optic vibration sensor is introduced and experimentally demonstrated in this study. The proposed system utilizes the transmission of light in the forward direction for sensing, and a self-interference method for laser source simplification. To extract vibration information from phase modulation of light, two Mach–Zehnder interferometers (MZIs) are employed with a 3 × 3 coupler-based differential cross multiplication algorithm for phase calculation. A folded double-ended detection configuration allows the time-of-flight difference via cross correlation (CC) to provide vibration positioning. Experimental results demonstrate a sensing range of up to ∼80 km without optical amplification, accompanied by a position accuracy of 336 m.

Undersea earthquakes can have a major impact on coastal cities, submarine infrastructure and environment. To provide advance warning and condition assessment, remote monitoring is critical. However, the current methods of undersea earthquake monitoring have some limitations, such as limited number of sensors, high deployment cost, severe signal attenuation, etc. In this study, we propose a new approach for super-long range vibration monitoring, by detecting vibration-induced phase change along a single sensing fiber using a double-ended forward-transmission distributed fiber-optic vibration sensing system with a compensated self-interference sensing mechanism. The experiment results show a single-span sensing range of 151.5 km without optical amplification, a spatial resolution of 10 m, and the position error can be as small as 37.6 m. The average sensitivity is ∼12.2 mrad/μϵ, and the average limit of detection is 186.7 pϵ/Hz1/2. The vibration frequency range tested is between 100-500 Hz. The sensing system has several advantages, such as super-long sensing distance, relatively low-coherence laser, anti-electromagnetic interference, etc. This study provides a new technical solution for undersea earthquake monitoring, which can improve the early warning and assessment capabilities of undersea earthquakes.

The deep integration of communication and sensing technology in fiber-optic systems has been highly sought after in recent years, with the aim of rapid and cost-effective large-scale upgrading of existing communication cables in order to monitor ocean activities. As a proof-of-concept demonstration, a high-degree of compatibility was shown between forward-transmission distributed fiber-optic vibration sensing and an on–off keying (OOK)-based communication system. This type of deep integration allows distributed sensing to utilize the optical fiber communication cable, wavelength channel, optical signal and demodulation receiver. The addition of distributed sensing functionality does not have an impact on the communication performance, as sensing involves no hardware changes and does not occupy any bandwidth; instead, it non-intrusively analyzes inherent vibration-induced noise in the data transmitted. Likewise, the transmission of communication data does not affect the sensing performance. For data transmission, 150 Mb/s was demonstrated with a BER of 2.8 × 10⁻⁷ and a Q_dB of 14.1. For vibration sensing, the forward-transmission method offers distance, time, frequency, intensity and phase-resolved monitoring. The limit of detection (LoD) is 8.3 pε/Hz^1/2 at 1 kHz. The single-span sensing distance is 101.3 km (no optical amplification), with a spatial resolution of 0.08 m, and positioning accuracy can be as low as 10.1 m. No data averaging was performed during signal processing. The vibration frequency range tested is 10–1000 Hz.

For distributed fiber-optic sensors, slowly varying vibration signals down to 5 mHz are difficult to measure due to low signal-to-noise ratios. We propose and demonstrate a forward transmission-based distributed sensing system, combined with a polarization-generated carrier for detection bandwidth reduction, and cross-correlation for vibration positioning. By applying a higher-frequency carrier signal using a fast polarization controller, the initial phase of the known carrier frequency is monitored and analyzed to demodulate the vibration signal. Only the polarization carrier needs to be analyzed, not the arbitrary-frequency signal, which can lead to hardware issues (reduced detection bandwidth and less noise). The difference in arrival time between the two detection ends obtained through cross-correlation can determine the vibration position. Our experimental results demonstrate a sensitivity of 0.63 mrad/με and a limit of detection (LoD) of 355.6 pε/Hz^1/2 at 60 Hz. A lock-in amplifier can be used on the fixed carrier to achieve a minimal LoD. The sensing distance can reach 131.5 km and the positioning accuracy is 725 m (root-mean-square error) while the spatial resolution is 105 m. The tested vibration frequency range is between 0.005 Hz and 160 Hz. A low frequency of 5 mHz for forward transmission-based distributed sensing is highly attractive for seismic monitoring applications.

The structural health of fiber-optic communication networks has become increasingly important due to their widespread deployment and reliance in interconnected cities. We demonstrate a smart upgrade of a communication system employing a dual-polarization-state polarization shift keying (2-PolSK) modulation format to enable distributed vibration monitoring. Sensing can be conducted without hardware changes or occupying additional communication bandwidth. Experimental results demonstrate that forward transmission-based distributed vibration sensing can coexist with PolSK data transmission without significant deterioration in performance. This proof-of-concept study achieved a sensitivity of 0.4141 μV/με with a limit of detection (LoD) of 563 pε/Hz^1/2@100 Hz. The single-span sensing distance can reach up to 121 km (no optical amplification) with a positioning accuracy as small as 874 m. The transmission rate is 300 Mb/s, the Q_dB is 16.78 dB, and the corresponding BER is 5.202 × 10⁻¹². For demonstration purposes, the tested vibration frequency range is between 100 and 200 Hz.