Metals are considered a suitable anode material for microbial fuel cells (MFCs) because of their high electrical conductivity. However, only a few types of metals have been used as anodes, and an extensive screening of metals has not yet been conducted. In this study, to develop a new metal anode for increased electricity generation in MFCs, 14 different metals (Al, Ti, Fe, Ni, Cu, Zn, Zr, Nb, Mo, Ag, In, Sn, Ta, and W) and 31 of their oxidized forms were comprehensively tested. Oxidized-metal anodes were prepared using flame oxidation, heat treatment, and electrochemical oxidation. The selected anodes were further evaluated in detail using air–cathode single-chambered MFCs. The untreated Mo and electrochemically oxidized Mo anodes showed high averages of maximum power densities in the screening test, followed by flame-oxidized (FO) W, FO-Fe, FO-Mo, and Sn-based anodes. The untreated Mo and FO-W anodes were selected for further evaluation. X-ray analyses revealed that the surface of the Mo anode was naturally oxidized in the presence of air, forming a layer of MoO3, a known oxidation catalyst. A high maximum power density (1296 mW/m2) was achieved using the Mo anode in the MFCs, which was superior to that obtained using the FO-W anode (1036 mW/m2). The Mo anode, but not the FO-W anode, continued to produce current without detectable corrosion until the end of operation (350 days). Geobacter was abundant in both biofilms on the Mo and FO-W anodes, as analyzed by high-throughput sequencing of the 16S rRNA gene. The screening test revealed that Mo, W, Fe, and Sn are useful MFC anode materials. The detailed analyses demonstrated that the Mo anode is a high-performance electrode with structural simplicity and long-term stability in MFCs. The anode can be easily prepared by merely shaping Mo materials to the desired forms. These properties would enable the large-scale preparation of the anode, required for practical MFC applications. This study also implies the potential involvement of Geobacter in the Mo and W cycles on Earth.

Biochemical oxygen demand (BOD) is a widely used index of water-quality assessment. Since bioelectrochemical BOD biosensors require anaerobic conditions for anodic reactions, they are not directly used in aerobic environments such as aeration tanks. Normally, the BOD biosensors are closed-type, where the anode is packed inside a closed chamber to avoid exposure to oxygen. In this study, a novel bioelectrochemical open-type biosensor was designed for in-situ monitoring of BOD during intermittent aeration. The open-type anode, without any protection against exposure to oxygen, was directly inserted into an intermittently aerated tank filled with livestock wastewater. Anodic potential was controlled using a potentiostat. Interestingly, this novel biosensor generated similar levels of current under both aerating and non-aerating conditions, and showed a logarithmic correlation (R² > 0.9) of current with BOD concentrations up to 250 mg/L. Suspended solids in the wastewater attached to and covered the whole anode, presumably leading to the production of anaerobic conditions inside the covered anode via biological oxygen removal. Exoelectrogenic anaerobes (Geobacter spp.) were detected inside the covered anode using the 16S-rRNA gene. This biosensor will have various practical applications, such as the automatic control of aeration intensity and the in-situ monitoring of natural water environments.

Carbon-based materials are commonly used as anodes in microbial fuel cells (MFCs), whereas metal and metal-oxide-based materials are not used frequently because of low electrical output. Stainless steel is a low-cost material with high conductivity and physical strength. In this study, we investigated the power generation using flame-oxidized (FO) stainless steel anodes (SSAs) in single-chambered air-cathode MFCs. The FO-SSA performance was compared to the performance of untreated SSA and carbon cloth anode (CCA), a common carbonaceous electrode. The difference in the anodic community structures was analyzed using high-throughput sequencing of the V4 region in 16S rRNA gene. Flame oxidation of SSA produced raised node-like sites, predominantly consisting of hematite (Fe2O3), on the surface, as determined by X-ray diffraction spectroscopy. The flame oxidation enhanced the maximum power density (1063 mW/m2) in MFCs, which was 184 and 24 % higher than those for untreated SSA and CCA, respectively. The FO-SSA exhibited 8.75 and 2.71 times higher current production than SSA and CCA, respectively, under potentiostatic testing conditions. Bacteria from the genus Geobacter were detected at a remarkably higher frequency in the biofilm formed on the FO-SSA (8.8–9.2 %) than in the biofilms formed on the SSA and CCA (0.7–1.4 %). Bacterial species closely related to Geobacter metallireducens (>99 % identity in the gene sequence) were predominant (93–96 %) among the genus Geobacter in the FO-SSA biofilm, whereas bacteria with a 100 % identity to G. anodireducens were abundant (>55 %) in the SSA and CCA biofilms. This is the first demonstration of power generation using an FO-SSA in MFCs. Flame oxidation of the SSA enhances electricity production in MFCs, which is higher than that with the common carbonaceous electrode, CCA. The FO-SSA is not only inexpensive but also can be prepared using a simple method. To our knowledge, this study reveals, for the first time, that the predominant Geobacter species in the biofilm depends on the anode material. The high performance of the FO-SSA could result from the particularly high population of bacteria closely related to G. metallireducens in the biofilm.