Hongdan Yu

Dr. Hongdan Yu


Research Focus & Metrics

Academic Career Length

6Years (2021-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
25 October 2021 in Bulletin of Engineering Geology and the Environment
Verified
Journal Article
Closed access
PDF file
HYHongdan Yu
Hongdan Yu
CLChen Lu
Chen Lu
WCWeizhong Chen
Weizhong Chen
HTHongming Tian
Hongming Tian

8 June 2024 in Natural Hazards
Verified
Journal Article
Open access
PDF file
KYKK Yuan
KK Yuan
BYBenhui Yu
Benhui Yu
MZMin Zhang
Min Zhang
YYYiran Yang
Yiran Yang
HYHongdan Yu
Hongdan Yu
The geological hazard of water–sand inrush is a matter of concern for infrastructure construction and resource exploration activities in China, due to the complex interplay between groundwater dynamics and the stability properties of sand particles. This phenomenon is characterized by its intensity, hazardous nature, and unpredictable behavior. Following comprehensive analysis, this study identifies the critical factors influencing water–sand inrush processes as fissure width, water stress (waterhead height), in-situ sand ground stress within the sand stratum, and clay content. To investigate these factors experimentally, a custom-designed hydraulically coupled water–sand inrush test apparatus was used. The apparatus was equipped with a cylinder to apply ground stress, a pneumatic diaphragm pump to regulate water stress, and a bottom opening in the sand layer. Tests were conducted to investigate the dynamic response of water–sand inrush events under various combinations of factor levels. The findings revealed that the critical value for inrush is only present in the fissure width, which was observed to be 3 mm for the tested sand material. Unlike fissure width, the other factors do not have definitive critical values but instead modulate the intensity of the inrush process without determining its occurrence. The ‘inrush rate’ serves as a measure of the severity of water–sand inrush disasters and shows a linear increase with both increasing groundwater stress and fissure width, a negative exponential function relationship between the inrush rate and the clay content. Notably, ground stress does not exert a significant influence on the intensity of the inrush process itself. Under constant conditions, the inrush rate remains relatively constant across different levels of sand ground stress, for instance, in the experiments, the inrush rate was measured at 1.606 kg/s when the water stress was 0.1 MPa and the fissure width was 5 mm. Grey relation analysis was used to examine the sensitivity of each factor’s influence on the inrush rate. The results showed that water stress has the greatest impact on the intensity of water–sand inrush, followed by ground or soil stress, clay content, and the width of the fissures in the sand layer.

8 April 2024 in Materials Letters
Verified
Journal Article
Closed access
HYHongdan Yu
Hongdan Yu
JHJiawei Huang
Jiawei Huang
HLHaifeng Lu
Haifeng Lu
WCWeizhong Chen
Weizhong Chen

22 September 2023 in Applied Sciences
Verified
Journal Article
Open access
PDF file
FLFanfan Li
Fanfan Li
Weizhong ChenWeizhong Chen
Weizhong Chen
ZWZhigang Wu
Zhigang Wu
HYHongdan Yu
Hongdan Yu
MLMing Li
Ming Li
FZFusheng Zha
Fusheng Zha
Claystone is potentially the main rock formation for the deep geological disposal of high-level radioactive nuclear waste. A major factor that affects the deformation of the host medium is effective stress. Therefore, studying the effective stress principle of claystone is essential for a stability analysis of waste disposal facilities. Consolidated drained (CD) tests were carried out on claystone samples to study their effective stress principle in this paper. Firstly, two samples were saturated under a specified confining pressure and pore pressure for about one month. Secondly, the confining pressure and pore pressure were increased to a specified value simultaneously and then reverted to the previous stress state (the deformations of the samples were recorded during the whole process). Different incremental combinations of the confining pressure and pore pressure were tried at this step. Finally, the effective stress coefficients of the samples were obtained through a back analysis. Furthermore, some potential influencing factors (the neutral stress and loading rate) of the effective stress coefficient were also studied through additional tests. Some interesting results are worth mentioning: (1) the effective stress coefficient of claystone is close to one; (2) the neutral stress and loading rate may have little effect on the effective stress coefficient of claystone.

5 August 2025 in Buildings
Verified
Journal Article
Open access
PDF file
KYKK Yuan
KK Yuan
MZMin Zhang
Min Zhang
LYLu Yichu
Lu Yichu
HYHongdan Yu
Hongdan Yu
This critical review synthesizes evidence on the multifactorial coupling mechanisms and time-dependent evolution of lateral pressure in concrete formworks, addressing significant limitations in current design standards (GB50666, CIRIA 108, ACI 347). Through a structured analysis of 60+ experimental and theoretical studies, we establish that lateral pressure is governed by nonlinear interactions between concrete rheology, casting dynamics, thermal conditions, and formwork geometry. The key findings reveal that (1) casting rate increments >5 m/h amplify peak pressure by 15–27%, while SCC thixotropy (Athix > 0.5) reduces it by 15–27% at 2 m exhibit 40% faster pressure decay due to arching effects. (4) Temporal evolution follows three distinct phases—rapid rise (0–2 h), slow decay (2–10 h), and sharp decline (>10 h)—with the temperature critically modulating transition kinetics. Crucially, the existing codes inadequately model temperature dependencies, SCC/HPC rheology, and high-speed casting (>10 m/h). This work proposes a parameter-specific framework integrating rheological thresholds (Athix, Rstr), casting protocols, and real-time monitoring to enhance standard accuracy, enabling an optimized formwork design and risk mitigation in complex scenarios, such as water conveyance construction and slipforming.

19 May 2025 in Scientific Reports
Verified
Journal Article
Open access
PDF file
KYKK Yuan
KK Yuan
BYBenhui Yu
Benhui Yu
ZFZhongxin Fan
Zhongxin Fan
JYJinhui Yang
Jinhui Yang
HYHongdan Yu
Hongdan Yu
Water-sand inrush has emerged as a significant geological hazard during underground construction in water-rich sand layers, posing severe risks to engineering safety. This study investigates the land subsidence caused by water-sand inrush using a custom-built, three-dimensional (3D) transparent model testing system. Experiments were conducted under four water pressures (0, 0.05, 0.1, and 0.15 MPa) and three clay contents (1%, 5%, and 10%). The findings indicate that both the rate and shape of land subsidence caused by water-sand inrush are significantly influenced by the clay content and water pressure. Primarily, the initial rate of water-sand inrush was determined by water pressure, whereas its effect on the final subsidence configuration is minimal. In contrast, clay significantly affects both the rate of sand inrush reduction and the final subsidence morphology. Increasing clay content from 1 to 10% reduced the maximum subsidence depth from 57.5 cm to 42 cm and extended the stabilization time from approximately 20–70 min. At clay concentrations below 5%, the subsidence trough has a two-stage characteristic, transitioning from a steep to a gentle slope. However, at higher clay contents (above 10%), the subsidence trough maintains a consistent gentle slope. No distinct steep section is observed. Based on these findings, a quantitative model was developed to describe the evolution of subsidence troughs resulting from water-sand intrusion. This model was validated against an actual engineering case in Yulin City, where the predicted maximum subsidence depth (4.04 m) and the subsidence radius (65.15 m) was accurately captured. The research results might provide guidance for predicting land subsidence due to water–sand mixing inrush hazard during the construction of tunnels or mines in viscous water-rich areas.