This study focused on the utilization of nano-MgO as an energy-saving and eco-friendly stabilizer to improve the engineering performance of loess. To this end, loess samples at various nano-MgO contents and curing times were prepared, and then standard compaction, consistency limits, and unconfined compression tests were performed. The achieved results demonstrated that adding nano-MgO increased the liquid limit, plastic limit, and optimum water content of loess, while it decreased the plastic index and maximum dry density. The unconfined compressive strength (UCS) presented an increasing trend with curing time and a “rise-fall” trend with the addition of nano-MgO. At the optimum nano-MgO content of 2%, about 72% UCS gain was to be expected with 28 days of curing. The variation of the deformation modulus was similar to that of UCS, and the strain at failure presented an opposite trend. Empirical models for these properties were formulated and validated by literature data. Finally, from NMR analyses, the improving mechanism was found to be nano-MgO induced water transformation from free water to bound water.
Subgrade stabilization is crucial for forest road construction, especially in Northeast China and the Russian Far East, with great economic growth potential. This study explored a novel and green solution of integrating biochar (BC), polyacrylamide (PAM), and straw fiber (SF) in the form of a ternary composite for stabilizing forest subgrade soil in cold regions. Using central composite design-based response surface methodology, the optimal mix ratio design was obtained, and the composite stabilizer was designated as BPS. Afterward, the stabilizing performance of BPS was studied by conducting an unconfined compression strength (UCS) test. The results showed that the optimum composition of BC:PAM:SF stood at 81:9:10. The UCS and deformation modulus with 3% BPS at 28 days reached 565.42 kPa and 17.24 MPa, respectively, which were 3.36 and 6.05 times higher than those of the untreated samples. The BPS-treated soil also possessed better resistance to freeze–thaw cycles. The freezing–thawing-induced loss ratio of strength was 49.3% lower than that of natural soil. Moreover, empirical models for the UCS of BPS-stabilized soil, as well as its relationships with the modulus, were established and validated by data in the literature. Finally, the “filling, cementing, and reinforcing” stabilization mechanism of BPS was elucidated by scanning electron microscopy analysis.
Underground void subsidence hazards, especially mine goaf, have now become one of the major social problems affecting the well-being of civilians and development in China. The objective of this study was to propose a kind of strong thixotropic engineering slurry and filling treatment for use in underground void subsidence hazards. The optimal agent ratio for thixotropic cement slurry/mortar was obtained by indoor tests, where the rheological agent is 7.5% compared to the weight of cement, the water–solid ratio is in the range of 0.7~0.8, and the aeolian sand ratio can be 0~1.5 times that of cement. The rheological properties of slurry and mortar were tested using a Brookfield RST-SST rheometer. The results show that aeolian sand can be used as thixotropic cement mortar for a backfilling treatment for underground voids (mine goaf). The static yield stress increases non-linearly compared to existing thixotropic models. The stress decays sharply with shearing (the shear rate is more or less 10 s−1) and then the stress increases with the increase in shear rate (the shear rate is more than 10 s−1). The increase in the stress of the slurry is greater than in the mortar. A natural logarithmic function between yield stress and rest time (only 1 parameter), an exponential function with two parts for stress–shear rate (a rheology model, with only 3 parameters), and an exponential function for the accumulation law (only 2 parameters) were proposed in turn.
The geological hazard of water–sand inrush is a matter of concern for infrastructure construction and resource exploration activities in China, due to the complex interplay between groundwater dynamics and the stability properties of sand particles. This phenomenon is characterized by its intensity, hazardous nature, and unpredictable behavior. Following comprehensive analysis, this study identifies the critical factors influencing water–sand inrush processes as fissure width, water stress (waterhead height), in-situ sand ground stress within the sand stratum, and clay content. To investigate these factors experimentally, a custom-designed hydraulically coupled water–sand inrush test apparatus was used. The apparatus was equipped with a cylinder to apply ground stress, a pneumatic diaphragm pump to regulate water stress, and a bottom opening in the sand layer. Tests were conducted to investigate the dynamic response of water–sand inrush events under various combinations of factor levels. The findings revealed that the critical value for inrush is only present in the fissure width, which was observed to be 3 mm for the tested sand material. Unlike fissure width, the other factors do not have definitive critical values but instead modulate the intensity of the inrush process without determining its occurrence. The ‘inrush rate’ serves as a measure of the severity of water–sand inrush disasters and shows a linear increase with both increasing groundwater stress and fissure width, a negative exponential function relationship between the inrush rate and the clay content. Notably, ground stress does not exert a significant influence on the intensity of the inrush process itself. Under constant conditions, the inrush rate remains relatively constant across different levels of sand ground stress, for instance, in the experiments, the inrush rate was measured at 1.606 kg/s when the water stress was 0.1 MPa and the fissure width was 5 mm. Grey relation analysis was used to examine the sensitivity of each factor’s influence on the inrush rate. The results showed that water stress has the greatest impact on the intensity of water–sand inrush, followed by ground or soil stress, clay content, and the width of the fissures in the sand layer.
An attempt was made to apply LBG in loess solidification. The impacts of applying LBG at various concentrations (0%, 0.5%, 1%, 1.5%, and 2%) and employing distinct curing periods (1, 2, 4, and 7 days) on the unconfined compressive strength, tensile strength, and disintegration characteristics were evaluated. The results demonstrated that an increase in the LBG content is correlated with an increase in both the uniaxial compressive strength and the tensile strength. Nevertheless, the rate of strength enhancement diminished progressively with higher LBG concentrations. A concentration of 2% is recommended for practical applications. The uniaxial compressive and tensile strengths of the LBG-modified loess samples were more than 1.5 times greater than those of the untreated loess samples. Moreover, the peak uniaxial compressive strength of the enhanced samples reached 426.8 kPa after seven days of curing. The improved soil also demonstrated excellent anti-disintegration performance, as evidenced by weight gain due to water absorption over the experimental period. Notably, no disintegration occurred during water immersion. The grass growth characteristic test results indicated that LBG-modified loess supported more vigorous growth. These results provide crucial reference data for ecological soil reinforcement and low-carbon construction.
Water-sand inrush has emerged as a significant geological hazard during underground construction in water-rich sand layers, posing severe risks to engineering safety. This study investigates the land subsidence caused by water-sand inrush using a custom-built, three-dimensional (3D) transparent model testing system. Experiments were conducted under four water pressures (0, 0.05, 0.1, and 0.15 MPa) and three clay contents (1%, 5%, and 10%). The findings indicate that both the rate and shape of land subsidence caused by water-sand inrush are significantly influenced by the clay content and water pressure. Primarily, the initial rate of water-sand inrush was determined by water pressure, whereas its effect on the final subsidence configuration is minimal. In contrast, clay significantly affects both the rate of sand inrush reduction and the final subsidence morphology. Increasing clay content from 1 to 10% reduced the maximum subsidence depth from 57.5 cm to 42 cm and extended the stabilization time from approximately 20–70 min. At clay concentrations below 5%, the subsidence trough has a two-stage characteristic, transitioning from a steep to a gentle slope. However, at higher clay contents (above 10%), the subsidence trough maintains a consistent gentle slope. No distinct steep section is observed. Based on these findings, a quantitative model was developed to describe the evolution of subsidence troughs resulting from water-sand intrusion. This model was validated against an actual engineering case in Yulin City, where the predicted maximum subsidence depth (4.04 m) and the subsidence radius (65.15 m) was accurately captured. The research results might provide guidance for predicting land subsidence due to water–sand mixing inrush hazard during the construction of tunnels or mines in viscous water-rich areas.