27 February 2020 in IEEE Access
In this work, wearable resistive gas sensors based on hybrid graphene/zinc oxide (ZnO) nanocomposites were fabricated on a flexible cotton fabric and employed to monitor odorless and colorless carbon monoxide (CO). Dip-coating and chemical bath deposition (CBD) was used to deposit the graphene layer and grow the ZnO nanorods, respectively. The films were characterized by scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDS), and X-Ray diffraction (XRD) to investigate their morphological structures, elemental composition, and crystal phase, respectively. Those characterizations were also confirming the growth of ZnO nanorods on the already-deposited graphene layer on fabrics. From the gas sensor measurements at room temperature, it is revealed that these graphene/ZnO nanocomposites were highly sensitive and selective towards CO gas at low concentration down to 10 ppm. The shortest response and recovery times of the sensors were measured to be 280 s and 45 s, respectively. Moreover, in comparison to bare graphene sensors, the surface modification by ZnO nanorods could obviously enhance the sensing response by up to 40% (i.e., doubled sensitivity). These flexible hybrid sensors are therefore expected to be a promising alternative for the existing rigid CO sensors in the market by offering unique nanostructures, low-cost fabrication, high flexibility, and good sensing performances.
11 January 2024 in Microchemical Journal
1 September 2022 in Journal of the Electrochemical Society
In this work, the amorphous HKUST-1 nanoparticles (aHKUST1) and copper hydroxide nanosheet (Cu(OH) 2 NS) were successfully prepared by involving diethanolamine (DEOA) and were applied as an immunosensor to detect dengue virus (DENV-3) NS1. 35 wt% of DEOA was found to not only provide a base environment but also act as a crystal modifier for the HKUST-1. The DEOA changes the crystallinity and morphology of HKUST-1 into amorphous and highly uniform nanoparticles, respectively. In addition, the Cu(OH) 2 NS was obtained by immersing the aHKUST1 NPs in water for 6 h. The aHKUST1 NPs and Cu(OH) 2 NS were functionalized as a matrix material to immobilize the DENV-3 monoclonal antibody. The immunosensor was fabricated by dropping the matrix on the surface of a screen-printed carbon electrode (SPCE). The immunosensor performances were evaluated by cyclic voltammetry (CV), differential pulse voltammetry (DPV), and electrochemical impedance spectroscopy (EIS) technique in detecting DENV-3 NS1 antigen at the concentration in the range of 0.001–100 ng ml −1 . As immunosensor aHKUST1 NPs and Cu(OH) 2 NS can detect the antigen down to 1.64 pg ml −1 and 2.07 pg ml −1 , respectively. The amorphous nature of HKUST-1 is believed to provide many active sites that can enhance electrocatalytic activities thereby improving immunosensor performance.
1 January 2014 in AIP Conference Proceedings
ZnO thin films with nanorod structure were deposited using Ultrasonic Spray Pyrolysis method for seed growth, and Chemical Bath Deposition (CBD) for nanorod growth. High purity Zn-hydrate and Urea are used to control Ph were dissolved in ethanol and aqua bidest in Ultrasonic Spray Pyrolysis process. Glass substrate was placed above the heater plate of reaction chamber, and subsequently sprayed with the range duration of 5, 10 and 20 minutes at the temperatures of 3500 C. As for the Chemical Bath Deposition, the glass substrate with ZnO seed on the surface was immerse to Zn-hydrate, HMTA (Hexa Methylene Tetra Amine) and deionized water solution for duration of 3, 5 and 7 hour and temperatures of 600 C, washed in distilled water, dried, and annealed at 3500 C for an hour. The characterization of samples was carried out to reveal the surface morphology using Scanning Electron Microscopy (SEM). From the data, the combination of 5 minutes of Ultrasonic Spray Pyrolysis process and 3 hour of CBD has showed the best structure of nanorod. Meanwhile the longer Spraying process and CBD yield the bigger nanorod structure that have been made, and it makes the films more dense which make the nanorod collide each other and as a result produce unsymetric nanorod structure.