Kou Teikai

Dr. Kou Teikai


Research Focus & Metrics

Academic Career Length

5Years (2022-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
15 April 2022 in Applied Sciences
Verified
Journal Article
Open access
PDF file
ZTZhilei Tian
Zhilei Tian
KTKou Teikai
Kou Teikai
WZWei Zhao
Wei Zhao
Jingchao GuanJingchao Guan
Jingchao Guan
XZXilu Zhao
Xilu Zhao
The truss core panel has been verified to be effective for structural weight reduction in former research studies. However, it is difficult to manufacture using the sheet metal pressing method because the forming height of the truss core panel is limited by the physical properties of the material. Although progressive stamping has been used to solve this problem, it is still difficult to practically use the truss core panel. In this study, the author proposed a manufacturing method and a hexagonal frustum intermediate structure to improve the forming quality of truss core panels using a progressive stamping method and verified its effectiveness through numerical analysis and prototype experiments. Compared to the conventional hemispherical intermediate model, the manufacturing process of the truss core panel using the proposed method was significantly improved.

24 March 2023 in Journal of Pressure Vessel Technology
Verified
Journal Article
Closed access
PDF file
YJYang Jing
Yang Jing
KTKou Teikai
Kou Teikai
JGJingchao Guan
Jingchao Guan
WZWei Zhao
Wei Zhao
XZXilu Zhao
Xilu Zhao
This paper proposes an integral hydrobulge forming (IHBF) method using a triangular patch polyhedron as the closed preform shell. When triangular flat parts are welded along the edges in sequence, triangular patch polyhedra are naturally formed. From the radius of the spherical pressure vessel, a design formula was derived to calculate the side lengths of the triangular flat plate parts. The water pressure, water volume, average strain of molding, and amount of springback after molding, which are necessary for implementing the IHBF for practical use, were also formulated. To verify the forming performance of the spherical pressure vessel using IHBF method, the finite element method was carried out, and a stainless-steel spherical pressure vessel with a thickness of 1.0 mm and a diameter of approximately 500 mm was fabricated using the proposed IHBF method. As a result, the measured shape error expressed as roundness to diameter ratio was 0.52%, and the calculated average plastic strain was 0.02, which was approximately 1/19 times of the forming limit strain of the material. The amount of springback after forming by calculation was approximately 0.7 mm, indicating that the amount of water required for IHBF was 5.90% of the volume of the spherical pressure vessel, while the required water pressure was no bigger than 2.3 MPa. The process directly utilizes triangular flat plate parts, eliminating the need for molds to process closed preform shells resulting in a low average plastic strain during forming, thereby improving the quality of the formed spherical pressure vessels.

18 October 2024 in International Journal of Mechanical Engineering and Applications
Verified
Journal Article
Open access
PDF file
JHJunfu Hou
Junfu Hou
LCLi Chen
Li Chen
KTKou Teikai
Kou Teikai
Jingchao GuanJingchao Guan
Jingchao Guan
WZWei Zhao
Wei Zhao
XZXilu Zhao
Xilu Zhao
When a tsunami is caused by an earthquake or other event, spherical shelters are developed to protect people from the tsunami. This study proposes a new egg-shaped laminated tsunami shelter with a buffer layer to improve the functionality of traditional spherical shelters. The inner and outer shells of this shelter are made from thin-walled stainless steel, using the integral hydro bulge forming (IHBF) process. The space between these two layers was filled with urethane foam, providing an elastic buffer. This resulted in a laminated egg-shaped structure designed for tsunami protection. To verify the proposed laminated egg-shaped tsunami shelter and its processing method, an egg-shaped shell with an external shape (length 660 mm, width 493 mm) was fabricated using a 1.0 mm thick stainless plate, and a laminated egg-shaped tsunami shelter with a 25 mm thick intermediate layer made of urethane foam was fabricated. The shape accuracy of the processed egg-shaped laminated tsunami shelter structure was measured, and the maximum error between the surface shape of the molded egg-shaped shell and the true egg shape was -4.13 mm, and the relative error to the maximum radius of the egg shape of 246.5 mm was -1.68%. In addition, to assess the buffering effect under external impact loads, acceleration sensors were attached to both the inner and outer layers of the fabricated egg-shaped laminated tsunami shelters. A hammer was used to apply an impact load to the outer layer, and the response acceleration values recorded by the sensors on both layers were compared. It was found that the response acceleration of the inner layer was 15.81% lower than that of the outer layer.

14 May 2025 in International Journal of Mechanical Engineering and Applications
Verified
Journal Article
Open access
PDF file
JHJunfu Hou
Junfu Hou
LMLingzhe Meng
Lingzhe Meng
KTKou Teikai
Kou Teikai
Jingchao GuanJingchao Guan
Jingchao Guan
WZWei Zhao
Wei Zhao
XZXilu Zhao
Xilu Zhao
The end surfaces of large storage tanks used in various industries are often composed of thin-walled metallic spherical cap structures. The ability to process these components at a low cost and with high manufacturing precision is an important research challenge. In this study, a new integrated free-bulge forming method is proposed to fabricate thin-walled metallic spherical cap structures. This method involves fixing the perimeter of a circular forming sheet, applying internal water pressure, and uniformly bulging the central portion of the sheet to achieve a spherical cap structure. To analyze the forming performance of the proposed method, formulas for calculating the plastic strain and average thickness during the process of forming the spherical cap from the circular sheet are derived, enabling a clear understanding of the workable range of the free-bulge forming method. Additionally, by deriving a prediction formula for the internal water pressure required for the free-bulge of the spherical cap structure, the key process design factors are identified. For verification, a free-bulge forming device is developed, and thin-walled metallic spherical cap structures are processed. The results confirm that the spherical cap shape is sufficiently precise and can be stably produced using the free-bulge forming method. Furthermore, a specialized device for measuring the shape accuracy of the spherical cap formed using the proposed free-bulge method is developed, and the surface shape of the spherical cap structure is measured. The results show that the formed spherical cap shape has a maximum deviation of 2.3% from the theoretical shape, demonstrating adequate precision for practical applications. To further verify the processing performance of the free-bulge forming method, the thickness distribution of the processed thin-walled metallic spherical cap is measured along its diameter. The results show that, compared to the original thickness of 1.0 mm, the minimum thickness of 0.858 mm occurs at the center of the spherical cap, representing a thickness reduction rate of -13.2%. It is confirmed that the free-bulge method can be stably applied to typical thin-walled press materials.