The deployable reflector antenna based on the synthetic aperture radar is a satellite component that consists of a unit structure in the form of a folded reflector. During the launch process, this satellite antenna is in the stowed condition to improve storage efficiency. It is then deployed to perform the space mission in the on-orbit condition. Due to these structural characteristics of the deployable reflector antenna, the reflector is possible to be loaded in the limited volume of the launch vehicle with the reduced size. Additionally, because the deployable reflector antenna is made by the lightweight material of the carbon fiber reinforced polymer and honeycomb core, it can reduce the launching cost and improve the revisit interval. In this paper, the conceptual design of the main reflector of the deployable reflector antenna was conducted. The main reflector was designed as the honeycomb sandwich composite structure. To design the main reflector, the stacking sequence of the composite material and honeycomb core was investigated to maximize the structural stiffness and minimize the antenna’s mass. Subsequently, finite element analyses including modal, quasi-static, structural–thermal coupling, and transient response were performed to numerically evaluate the structural performance of the lightweight composite reflector antenna.
A deployable reflector antenna (DR-A) is a structure that can be stored in a large-diameter Synthetic Aperture Radar (SAR) antenna and be mounted onto a launch vehicle. Considering the performance of the launch vehicle, it is necessary to develop a lightweight, high-performance antenna structure. The solid-type deployable reflector antenna is composed of a number of unit main reflectors. To reduce the weight of the antenna, a lightweight main reflector must be developed. In this paper, following “Development of Deployable Reflector Antenna for the SAR Satellite (Part 1)”, the manufacturing and qualification of the main reflector using honeycomb sandwich composites are described. Four types of composite main reflectors were manufactured with variables in the manufacturing process. The manufacturing variables include the curing process of the structure, the application of an adhesive film between the sheet and the core, and the venting path inside of the sandwich core. After manufacturing the main reflector, we performed weight measurements, non-destructive testing (NDT), surface error measurement using a Coordinate Measurement Machine (CMM), and modal testing for each type of composite main reflector. Through the research and development process, we found that a perforated hole is necessary when excluding the adhesive film during bonding of an aramid core and a CFRP sheet, and a lightweight composite reflector could be developed through this process. We selected the main reflector with the best performance and developed a composite main reflector that can be applied to satellites.
In the launch environment, satellites are subjected to severe dynamic loads. These dynamic loads in the launch environment can lead to the malfunction of the payload, or to mission failure. In order to improve the structural stability of satellites and enable the reliable execution of space missions, it is necessary to have a reinforcement structure that reduces structural vibrations. However, for active small SAR satellites, the mass requirements are very strict, and this makes it difficult to apply an additional structure for vibration reduction. Therefore, we have developed a carbon fiber-reinforced plastic (CFRP)-based laminated patch to obtain a vibration reduction structure with a lightweight design for improving the structural stability of an S-STEP satellite. To verify the vibration reduction performance of the CFRP-based patch, sine and random vibration tests were conducted at the specimen level. Finally, the structural stability of the S-STEP satellite with the proposed CFRP-based laminated patch was experimentally verified using sine and random vibration tests. The validation results indicate that the CFRP-based laminated patch is an efficient solution which can effectively reduce the vibration response without the need for major changes to the design of the satellite structure. The lightweight vibration reduction mechanism developed in this study is one of the best solutions for protecting vibration-sensitive components.
The deployable reflector antenna mounted on the SAR satellite is an antenna with a folding structure and is one of the main components of the satellite body. Due to the limited space inside the launch vehicle fairing, the mounting efficiency was improved by applying a structural feature that allows the antenna to be stowed compactly. In addition, weight reduction was required to lower launch costs and improve the satellite revisiting cycle; therefore, the main reflector of the deployable reflector antenna was designed and manufactured using carbon fiber reinforced polymer and aramid honeycomb core. Since the main reflector made of carbon fiber-reinforced polymer and aramid honeycomb core is not an isotropic material, differences between theoretical and actual thermal properties were expected. Therefore, in this study, a thermal balance test was performed on the thermal structure model of the deployable reflector antenna, and the thermal analysis model simulated by the ground test was corrected using the verified temperature conditions as a reference. The thermal properties of the composite material and the thermal conductivity coefficient between the main reflector and the main components connected to it were the targets of correction. In addition, a numerical optimization technique was applied to reduce computational costs, and the thermal analysis assumed the orbital environment model of the deployable reflector antenna was optimized using the corrected thermal properties.
The concept of synthetic aperture radar (SAR) has the advantage of being able to obtain high-quality images even when the target area is at night or covered with obstacles such as clouds or fog. These imaging capabilities have led to a rapid increase in demand for space SAR imagery across a variety of sectors, including government, military, and commercial sectors. The SAR-based deployable reflector antenna was developed in this series of paper. The satellite performance is influenced by the aperture size of an antenna. To improve the image acquisition performance, the SAR antenna has the configuration of several foldable CFRP reflectors. In this paper, the experimental investigation of the Structural-thermal model deployable reflector antenna is performed. During the launch condition, the satellite and payload are subjected to the dynamic load. In the STM phase, the acoustic test was conducted to evaluate the structural stability of the deployable reflector antenna within the acoustic environment. The sinusoidal vibration test was implemented to investigate the fundamental frequency for inplane/normal directions and evaluate the structural stability of reflector antenna. By using experimental data obtained from the thermal-balance test, the well-correlated thermal analysis model was established to execute the orbital thermal analysis. The experimental results of the environmental test in STM phase show that the deployable reflector antenna has structural stability for the structural/thermal environments. The configuration of the deployable reflector antenna determined in STM phase can be applied to the qualification model.
This study is an initial study for the development of a large truss-type deployable mesh antenna, and it involved the development process of a 1.5 m-scale deployable mesh antenna. The geometric characteristics of the reflector were considered for the initial net design. Based on the antenna’s operating frequency, the L-band, the surface root mean square (RMS) error and focal length/diameter (F/D) ratio of the reflector were calculated. Design requirements for the antenna’s weight, stowed/deployed dimensions, and fundamental frequency were established. The material properties of each component were applied to the design model, and the geometric dimensions were verified to ensure that the weight and stowed/deployed design were fulfilled. The fundamental frequency requirements under stowed/deployed conditions were verified through modal analysis, and the structural deformation of the ring truss was confirmed through load analysis. The reflector antenna was assembled to the ring truss with the net and mesh, according to the assembly procedure. The curvature of the reflector surface was shaped by adjusting the bolt length of the tension control device. Using V-Stars, a specialized surface error measurement device, the surface RMS error requirements for the reflector were confirmed to be satisfied. Finally, the development verification of the antenna was completed by performing repeated deployment and a thermal vacuum test.