The fluidic pintle nozzle, a new method to control the thrust of a solid rocket motor, has been proposed in recent years by combining the pintle with the aerodynamic throat (fluidic throat). The study of static characteristics has proved that it has a remarkable effect on thrust control. To study the transient characteristics of the fluidic pintle nozzle, 2D transient simulations of a fluidic pintle nozzle propulsion system were conducted, employing dynamic meshing techniques. The Reynolds-averaged Navier–Stokes equations were meticulously solved, implementing a k–ω SST turbulence model. The thrust control principle of the fluid pintle nozzle was studied, and the wave structure was summarized. The transient characteristics of the secondary flow opening, secondary flow closing, pintle moving forward (pressure rise), and pintle moving backward (pressure drop) were obtained, and the effects of the injection angle and injection port position were studied. The response process after injection can be roughly divided into three stages: pressure propagation, pressure oscillation, and equilibrium stability, with time distributions of 0.4%, 5.39%, and 94.21%, respectively. In the process of the pintle moving forward, the rate of combustion chamber pressure increases and thrust decreases gradually because of the arc wall of the nozzle throat upstream, and the process of throats moving backward is just the opposite. Compared with the condition with a maximum throat opening and no secondary flow, the thrust of the condition with a minimum throat opening and a 0.3-flow-ratio secondary flow is increased by 80.95%. Under conditions of constrained flow ratio, the injection angle of the secondary flow ostensibly exerts negligible influence on the dynamic modulation of thrust. Nevertheless, it remains evident that a reduction in throat opening accentuates the impact of reverse injection. Furthermore, the proximity of the injection port to the head of the pintle is directly proportional to the efficacy of thrust control.
10 May 2023 in International Journal of Aerospace Engineering
To develop an effective suction slot arrangement, computational fluid dynamics simulation software and a high subsonic compressor cascade were used to simulate different suction slots. Based on the effects of various suction slots on the cascade performance under various operating conditions, a novel segmented suction slot structure Seg3 was proposed. The results of the study revealed that in the vicinity of the operating conditions ( ), a full-blade height suction slot should be installed at least 5% of the chord length downstream of the corner separation point to effectively remove the separation. For small and medium incidences, the best performance was observed for suction slot SS5, which was located at 60% of the chord length downstream of the leading edge. Analyzing the effects of SS5 and Seg3 on the cascade performance revealed that when the incidence was less than 4°, the reductions in the total pressure loss coefficients for ζsuc of SS5 and Seg3 both exceeded 8.2%. When the incidence was 4° or greater, the ζsuc increased slightly for SS5, whereas it decreased for Seg3, and the ζsuc was reduced. For a 3° incidence, for example, Seg3 reduced the ζsuc and passage blockage by 12.74% and 8.41%, respectively, and increased the static pressure rise coefficient by 18.55% from the baseline values. Thus, the segmented suction slot proposed in this paper outperformed conventional full-blade height suction slots.
3 January 2026 in International Journal of Aerospace Engineering
Human factors play an important role in civil aviation safety, which is also vital in flight tests. To significantly reduce the possibility of accidents induced by human errors during the flight test, systematic assessment of human factor risks, determination of the critical causes of accidents, and designs of targeted preventive strategies are imperative. The scarcity and confidentiality of flight test accident data pose significant challenges to the quantitative assessment of human factor risks. This paper proposes a novel model to assess human‐induced risks in flight tests, which enables the quantitative analysis of risk factors. The HFACS model has been adaptively improved to more comprehensively identify human‐related risk factors in flight tests. By integrating the fault tree model with the fuzzy Bayesian network, this study calculates the quantitative value of the probability of hazard occurrence. Furthermore, this study incorporates the impacts of individual differences on the consistency of expert ratings via the improved similarity aggregation method. The paper concludes with a case analysis that identifies the most critical human factors in civil aircraft flight tests, thereby providing valuable insights for formulating preventive measures and optimizing risk management strategies.
19 April 2023 in International Journal of Aerospace Engineering
To examine the impact of oxidative jets on the thrust vector angle, secondary combustion efficiency, and combustion chamber pressure, inert gas (nitrogen) and pure oxygen are injected into the primary flow, which includes combustible components, at various locations in the divergence section and throat using different injection techniques. The simulations utilize Reynolds-averaged Navier-Stokes equations coupled with the SST - turbulence model in two-dimensional numerical simulations and large-eddy simulation in three-dimensional studies. The numerical method is validated through schlieren experiments, and the vortex is identified using the Liutex-Omega method. The vortex structures and flow characteristics are analyzed. The results indicate that, at the same flow rate, the vector control effect of pure oxygen is superior to nitrogen only in the divergence section, but inferior to nitrogen in both the divergence section and throat. However, with improved vector control, the peak of the vector angle is achieved at a lower flow rate in the case of pure oxygen. When the secondary flow is introduced only in the divergence section, the flow ratio corresponding to the peak point in the pure oxygen case is approximately 14.3% earlier than that in the nitrogen case. The introduction of the pure oxygen jet enhances the secondary combustion efficiency of the primary flow, but to a limited extent. Additionally, when the jet is introduced at the throat, the effect of the pure oxygen case on adjusting the combustion chamber pressure is inferior to that of the nitrogen case. Concerning flow details, the trailing lower vortex replaces the trailing major vortex to become the highest magnitude vortex when the momentum flux ratio is small.