In this article, a high-gain bidirectional quadratic dc–dc converter is proposed. This converter is studied under step-up and step-down modes. In each power flow direction, two switches and two antiparallel diodes of the other switches operate. Therefore, the switching losses depend only on the operation of two switches in each direction. The use of coupled inductor in the proposed converter significantly reduces the input and output current ripples of the step-up and step-down modes, respectively, at all operating points of continuous and discontinuous conduction modes (CCM and DCM). The voltage gain of the proposed converter in the step-up mode is as high as that of the cascaded boost converter, and in the step-down mode, the converter voltage gain is similar to that of the cascaded buck converter. Thus, the high-voltage conversion ratio with an appropriate duty-cycle in both power flow directions can be achieved. The operating principles and steady-state analysis of the proposed converter in CCM, DCM, and the boundary-conditions between these modes are discussed in detail. Finally, a prototype of the converter is implemented in the laboratory and the experimental results are presented to validate the effectiveness of the proposed converter.
29 April 2022 in IEEE Transactions on Industrial Electronics
Wireless power transfer systems require compensators to improve efficiency by increasing transfer power between transmitter and receiver. The most commonly used compensators are series-series (SS), series–parallel, and double-sided LCC. This article analyzes the comparison between typical compensators focusing on transfer efficiency. Due to these characteristics of typical compensators, a hybrid compensation topology is designed based on two compensators. Hybrid compensation topology is capable of switching between SS and double-sided LCC topologies. Two ac switches are used on the transmitter and receiver for switching mode in hybrid compensation topology with wireless communication links, and its variation algorithm is clarified. A novel compensation topology guarantees system’s efficiency for a wide range of loads based on the maximum efficiency of two compensation topologies. The possibility of a proposed hybrid compensator is verified with an experimental prototype used for massive vehicles.
17 August 2022 in IEEE Transactions on Industrial Electronics
In this article, we present a new nonisolated high-gain (HG) dc–dc topology. Using a magnetically coupled inductor, the proposed topology can reach a higher voltage gain than those of the other topologies with a moderate duty cycle. The voltage gain will be expanded further by enhancing duty cycle of the active power switch or the turn ratio ( N ). The resonance passive clamping circuits are presented to recycle the energy of leakage inductance and mitigating voltage spikes on the primary power mosfet efficaciously. Then, the output diode's reverse-recovery problem is lightened by the resonance between the leakage inductance and resonance capacitor. Accordingly, the efficiency of the presented HG converter can be improved. The active power switch turns on and off in the zero-current switching and zero-voltage switching modes, respectively. The numerical investigation and MATLAB/Simulink simulations are depicted in detail. Likewise, an experimental setup is developed using a 100 W solar panel that supplies the suggested dc–dc converter, validating the introduced analysis and simulations.
21 September 2021 in IEEE Transactions on Power Delivery
The HVDC systems have been employing modular multilevel converters (MMC) due to their unique high voltage high power potential. However, the lack of fault ride-through capability imposes restrictions on MMCs that are based on half-bridge (HB) modules. Since it is necessary to limit the fault currents to protect MMCs from serious short circuit faults against pole-to-pole DC fault, several protection schemes have been introduced to deal with the DC short circuit faults. This paper proposes a new hybrid MMC protective topology consisting of a combination of the HB and three-quarter-bridge (TQB) modules. The TQB behaves like an HB under normal operation and has low power losses compared to other protective topologies. Modulation and control of this configuration are like HB-based MMC. In the proposed hybrid protective topology, during a pole to pole DC fault, the fault current can be either blocked or be limited by TQB-SMs. Both simulations and experiments were performed to verify the operation of the suggested hybrid MMC in different modes of operation.
This article suggests a non‐isolated high step‐up interleaved DC–DC topology for renewable energy applications. Two three‐winding coupled‐inductors along with two voltage multiplier cells are used to enhance the voltage gain significantly. One interesting aspect of this new topology is that high duty cycles are not required to achieve high voltage gains; this is done by adjusting the turn ratio of the coupled inductors. Moreover, the presented interleaved converter enjoys not only having less current stress due to the interleaving structure, but also showing 16% increase in voltage gain compared to the best similar boost topologies. Additional elements are designed for the purpose of soft switching and gain increase, which have little effect on the cost, weight and size of the proposed converter. Interestingly, the voltage stresses both on the switching devices and passive elements are much less than the output voltage. Furthermore, the coupled inductor's leakage inductance energy is recovered by employing a passive clamp circuit to minimize stresses across the semiconductors; therefore, efficiency is improved. The suggested converter is analyzed in the steady state, and a 400 W experimental setup was implemented; the outcomes verify the practicality of the proposed boost converter in accordance with the analysis.
27 September 2021 in IET Renewable Power Generation
Modelling the uncertainty of wind speed is essential in power flow analysis. Having abundant knowledge of the wind speed in an area is critical. A low volume of data can increase uncertainty in wind speed analysis. Spatial dependencies are often modelled before running probabilistic power flow and load flow analysis. Copulas are a popular way of capturing spatial dependence between multiple wind farms. Using NREL data from seven Northeastern United States wind farm sites, Bayesian inference will be used to determine the copula parameter uncertainty between weekly, daily, and hourly wind speed observations. This approach will be used on elliptical and single parameter Archimedean copulas. For each possible wind farm pair, an uninformative prior will be placed on the copula parameter. The resulting posterior will contain a distribution of copula parameter values based on the prior and the observed wind speed data. The posterior's credible interval is reviewed to determine the uncertainty in parameter estimation. The results show that using a data volume considerably more petite than 8760 hourly data points will result in more uncertainty in parameter estimation and inaccuracies in wind speed forecasting if using non‐Bayesian methods for copula parameter estimation.