Mohammad Tavakoli Bina

Dr. Mohammad Tavakoli Bina


Research Focus & Metrics

Academic Career Length

23Years (2004-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
3 August 2010 in Energy Conversion and Management
Verified
Journal Article
Closed access
SRSajad Rahimzadeh
Sajad Rahimzadeh
MBMohammad Tavakoli Bina
Mohammad Tavakoli Bina

17 August 2022 in IEEE Transactions on Industrial Electronics
Verified
Journal Article
Closed access
SASohrab Abbasian
Sohrab Abbasian
MFMohammad Farsijani
Mohammad Farsijani
MBMohammad Tavakoli Bina
Mohammad Tavakoli Bina
ASAmir Shahirinia
Amir Shahirinia
In this article, we present a new nonisolated high-gain (HG) dc–dc topology. Using a magnetically coupled inductor, the proposed topology can reach a higher voltage gain than those of the other topologies with a moderate duty cycle. The voltage gain will be expanded further by enhancing duty cycle of the active power switch or the turn ratio ( N ). The resonance passive clamping circuits are presented to recycle the energy of leakage inductance and mitigating voltage spikes on the primary power mosfet efficaciously. Then, the output diode's reverse-recovery problem is lightened by the resonance between the leakage inductance and resonance capacitor. Accordingly, the efficiency of the presented HG converter can be improved. The active power switch turns on and off in the zero-current switching and zero-voltage switching modes, respectively. The numerical investigation and MATLAB/Simulink simulations are depicted in detail. Likewise, an experimental setup is developed using a 100 W solar panel that supplies the suggested dc–dc converter, validating the introduced analysis and simulations.

25 May 2021 in IEEE Access
Verified
Journal Article
Open access
MAMohsen Akbari
Mohsen Akbari
MBMohammad Tavakoli Bina
Mohammad Tavakoli Bina
ABAmir Sajjad Bahman
Amir Sajjad Bahman
BEBahman Eskandari
Bahman Eskandari
EPEdris Pouresmaeil
Edris Pouresmaeil
Frede BlaabjergFrede Blaabjerg
Frede Blaabjerg
An accurate and real-time knowledge of temperatures in insulated-gate bipolar transistor modules is crucial for reliability analysis and thermal management of power electronic converters. For this purpose, this paper establishes an integrated thermal equivalent circuit model comprising self-heating thermal impedances and cross-heating thermal impedances to provide a temperature profile of the junction and solder joints during various operations and in the case of thermal aging. The thermal resistance and capacitance parameters of the thermal impedances are characterized in terms of different electro-thermal operating conditions and solder joints aging conditions with the help of three-dimensional finite element simulations. Also, the effect of the heatsink, which brings an uneven heat transfer coefficient distribution at the module baseplate, is investigated and modeled into the thermal impedances. The introduced thermal model can work even if the conditions change simultaneously. The accuracy of the model is verified by experiments and finite element simulations, all of which agree with negligible error unlike thermal models given in the datasheet and fixed-parameter thermal models.

8 July 2019 in IEEE Access
Verified
Journal Article
Open access
ZAZakaria Afshar
Zakaria Afshar
MMMahmud Mollayousefi
Mahmud Mollayousefi
SBSeyed Mohammad Taghi Bathaee
Seyed Mohammad Taghi Bathaee
MBMohammad Tavakoli Bina
Mohammad Tavakoli Bina
Gevork B. GharehpetianGevork B. Gharehpetian
Gevork B. Gharehpetian
In autonomous microgrids, the well-known frequency, and voltage droop control are extensively used to share active and reactive powers among parallel inverters without using any communication infrastructure. However, power sharing is performed at the expense of altering the voltage and frequency of the system. To restore the voltage and frequency to their nominal amounts, a secondary control loop is often augmented to the system using communication links. To avoid using these complex hierarchical controls, this paper proposes a novel method for power sharing in parallel inverters providing constant frequency and nominal voltage operation for critical loads. The proposed method uses a simple structure based on communication links utilization. The simulation results show that the active and reactive powers are accurately shared with an acceptable transient response. Furthermore, the results are compared with the conventional droop control, to show the superiority of the proposed method over the conventional one.

6 October 2020 in IEEE Transactions on Electromagnetic Compatibility
Verified
Journal Article
Closed access
RAReza Amjadifard
Reza Amjadifard
MBMohammad Tavakoli Bina
Mohammad Tavakoli Bina
HKHamid Khaloozadeh
Hamid Khaloozadeh
FBFarhad Bagheroskouei
Farhad Bagheroskouei

3 January 2023 in IEEE Access
Verified
Journal Article
Open access
MFMohammad Farsijani
Mohammad Farsijani
SASohrab Abbasian
Sohrab Abbasian
Hossein HafeziHossein Hafezi
Hossein Hafezi
MBMohammad Tavakoli Bina
Mohammad Tavakoli Bina
KAKarim Abbaszadeh
Karim Abbaszadeh
The need for high gain DC-DC converters has lately increased in tandem with the utilization of renewable energy supplies. Particularly appealing are high gain converters that do not require the inclusion of extra power switches and/or other passive elements to the system. As a result, this study proposes a non-isolated single switch converter with ultra-high voltage gain (UHG) that is appropriate for most renewable energy conversion systems, like solar installations. With only a single MOSFET working within a suitable duty cycle region, the proposed converter provides significant voltage gain and around 95% efficiency. Moreover, the MOSFET in this UHG converter is turned on in zero current switching (ZCS) mode, resolving the diode recovery issue. The recommended UHG converter’s working modes, steady-state parametric study, circuit variables like voltage stress on switching devices, and converter gain are all thoroughly explained. Comparisons have been done with comparable topologies presented in the literature, and lastly, experimental results depending on 200W (20V input, 320V output voltage) are given to validate the operation of the proposed UHG design.