Krzysztof Rokicki

Krzysztof Rokicki

orcid

Research Focus & Metrics

Academic Career Length

7Years (2020-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
22 November 2024 in Sensors
Verified
Journal Article
Open access
PDF file
ARAndrzej Reński
Andrzej Reński
MBMateusz Brukalski
Mateusz Brukalski
HSHubert Sar
Hubert Sar
MAMichał Abramowski
Michał Abramowski
Piotr FundowiczPiotr Fundowicz
Piotr Fundowicz
KRKrzysztof Rokicki
Krzysztof Rokicki
The motion of automobiles significantly depends on the conditions of interaction between a tyre and a road surface. One of the most frequently used ways of presenting the conditions of cooperation between a tyre and a road surface is a characteristic showing a longitudinal adhesion coefficient as a function of a longitudinal slip of a tyre. One of the methods for determining tyre-to-road adhesion characteristics is to use a special trailer combined with a towing vehicle. This type of method is commonly used to determine adhesion characteristics for a braked wheel. This article presents a method for determining adhesion characteristics for a driven wheel based on the road tests of automobiles. For this purpose, vehicle wheel velocity signals from a vehicle CAN network and a vehicle velocity signal from a GPS receiver were used. The signals from the CAN network were recorded using a special measurement card and an application developed in LabVIEW environment. The application developed in LabVIEW also allowed for simultaneous recording of automobile velocity from the GPS receiver. In this paper, the courses of a wheel velocity, longitudinal acceleration of automobile, longitudinal slip of the front wheels in time domain, as well as the coefficient of tyre-to-road longitudinal adhesion as a function of the longitudinal slip of the wheel are presented.

30 March 2020 in The Archives of Automotive Engineering - Archiwum Motoryzacji
Verified
Journal Article
Open access
HSHubert Sar
Hubert Sar
MBMateusz Brukalski
Mateusz Brukalski
KRKrzysztof Rokicki
Krzysztof Rokicki
Development of active safety systems of automobiles is nowadays based not only on road tests, but also on computer simulation of vehicle's curvilinear motion. To properly perform simulation, all required model parameters have to be properly estimated. The less complicated model is, the less parameters it requires. So that, it makes no sense to apply too complicated models, if we are not able to estimate parameters with relatively low error. One of the most popular is two- degree-of-freedom flat model to describe curvilinear motion of automobile. It is widely used in design and improvement of active safety systems. The article discusses the application of simple two- degree-of-freedom flat model of automobile, which requires only several parameters. These parameters are: mass of a vehicle, location of center of gravity of a vehicle, yaw mass moment of inertia of a vehicle, side-slip characteristics. Furthermore, to be able to compare simulation and measurement results, it is necessary to know some input signals such as steering wheel angle and velocity of a vehicle, recorded during road tests. In this article signal of steering wheel angle was taken from Controller Area Network (CAN) bus. In case of model of a vehicle, the Authors decided to compare the results of simulation using two different side slip characteristics known as the dependence between lateral reaction force and side slip angle: linear characteristic (constant cornering stiffness) and the characteristic represented by Pacejka’s Magic Formula in steady-state version.

1 July 2021 in Communications - Scientific letters of the University of Zilina
Verified
Journal Article
Open access
PDF file
HSHubert Sar
Hubert Sar
MBMateusz Brukalski
Mateusz Brukalski
KRKrzysztof Rokicki
Krzysztof Rokicki
Modelling of vehicle's motion is one of the solutions applied in the research of automotive safety. There is always a discussion which model should be used for computer simulation. Models with higher number of degrees of freedom require identi...