Most material removal in modern manufacturing is currently performed using tools with indexable inserts. Additive manufacturing allows for the creation of new, experimental insert shapes and, more importantly, internal structures, such as channels for coolant. This study deals with developing a process for efficiently manufacturing WC-Co specimens with internal coolant channels with a focus on obtaining a suitable microstructure and surface finish, especially inside the channels. The first part of this study covers the development of process parameters to achieve a microstructure without cracks and with minimal porosity. The next stage focuses solely on improving the surface quality of the parts. Special attention is given to the internal channels, where true surface area and surface quality are evaluated, as these characteristics greatly influence coolant flow. To conclude, WC-Co specimens were successfully manufactured and a microstructure with low porosity and no cracks was achieved and an effective parameter set was found. We have developed a process that produces parts with a surface roughness comparable to those of standard SLS manufacturing of steel parts, while still providing a high-quality internal microstructure. The most suitable parameter set resulted in a profile surface roughness of Ra 4 μm and Rz 31 μm and areal surface roughness of Sa 7 µm and Sz 125 µm.

In this study, the influence of laser polishing on the microstructural and mechanical properties of additively manufactured aluminium AlSi10Mg Laser Powder Bed Fusion (L-PBF) parts is analysed. The investigation is carried out on a 5-axis laser cell equipped with 1D Scanner optics driven by a solid-state disc laser at a wavelength of 1030 nm. Laser polishing is performed with pulsed or continuous laser radiation on samples in the initial L-PBF state or after stress relief treatment in a furnace. The metallurgical investigation of the remelting zone with a depth of 101–237 µm revealed an unchanged and homogeneous chemical composition, with a coarsened α-phase and a changed grain structure. The hardness within the remelting zone is reduced to 102–104 HV 0.1 compared to 146 HV 0.1 at the L-PBF initial state. Below the remelting zone, within the heat affected zone, a reduced microhardness, which can reach a thickness up to 1.5 mm, occurs. Laser polishing results in a reduction in residual stresses and resulting distortions compared to the L-PBF initial state. Nevertheless, the re-solidification shrinkage of the polished surface layer introduces additional tensions, resulting in sample distortions well above ones remaining after a stress relieve heat treatment of the initial state. The mechanical properties, analysed on laser polished flat tensile specimens, revealed an increase in the ultimate elongation from 4.5% to 5.4–10.7% and a reduction in the tensile strength from 346 N/mm² to 247–271 N/mm² through laser polishing. Hence, the strength resulting from this is comparable to the initial L-PBF specimens after stress relieve heat treatment.

Chromium and silicon are often introduced to increase the performance of TiAlN hard coatings in dry tribological contacts. The addition of Cr and Si during a high-power impulse magnetron sputtering (HiPIMS) deposition process leads to high-quality TiAlCrSiN films. In this paper, the analysis of friction and wear of these films is conducted by oscillation tribometry under dry conditions with a subsequent mapping of the surface topography. Both abrasion- and adhesion-dominated conditions are realized using different steel counter bodies. Oscillation-frequency-dependent experiments show a significant impact of the compositional variation on friction and wear. It is shown that the TiAlCrSiN coating investigated has a higher coefficient of friction and a lower wear resistance compared to counterparts made of 100Cr6. The friction coefficient could be reduced by using a V2A counterpart. The results can be understood in terms of a reduced adhesion of both oxidic and metallic wear debris at the TiAlCrSiN surface. The study provides valuable progress towards the development of advanced cutting tools, e.g., for stainless steel.

Tungsten carbide-cobalt hard metal produced by additive manufacturing offers opportunities to meet the increasingly complex requirements of high-performance machining. Besides a high level of design freedom and the easy integration of functional properties, the additive manufacturing of hard metals also offers potential for cost savings and conservation of resources. A window of favorable process parameters for laser beam melting was established using commercially available carbide powder with 17 % Co content, which serves to build carbide samples by laser-based additive manufacturing. Compared to conventionally manufactured carbides, deviations can still be noticed with regard to microstructural and mechanical properties. However, bending strengths of > 1 000 MPa and fracture toughness in the range of 10–12 Mpa √m are promising for the future additive manufacturing of WCCo hard metals.

Numerous studies show that vat photopolymerization enables near-net-shape printing of ceramics and plastics with complex geometries. In this study, vat photopolymerization was investigated for cemented carbide specimens. Custom-developed photosensitive WC-12 Co (wt%) slurries were used for printing green bodies. The samples were examined for defects using quantitative microstructure analysis. A thermogravimetric analysis was performed to develop a debinding program for the green bodies. After sintering, the microstructure and surface roughness were evaluated. As mechanical parameters, Vickers hardness and Palmqvist fracture toughness were considered. A linear shrinkage of 26–27% was determined. The remaining porosity fraction was 9.0%. No free graphite formation, and almost no η-phase formation occurred. WC grain growth was observed. 76% of the WC grains measured were in the suitable size range for metal cutting tool applications. A hardness of 1157 HV10 and a Palmqvist fracture toughness of 12 $\mathrm{MPa}\sqrt{\mathrm{m}}$ was achieved. The achieved microstructure exhibits a high porosity fraction and local cracks. As a result, vat photopolymerization can become an alternative forming method for cemented carbide components if the amount of residual porosity and defects can be reduced.