Francisco J. Rodríguez-Dopico

Mr. Francisco J. Rodríguez-Dopico

orcid

Research Focus & Metrics

Academic Career Length

4Years (2023-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
13 October 2024 in Ocean Engineering
Verified
Journal Article
Open access
FRFrancisco J. Rodríguez-Dopico
Francisco J. Rodríguez-Dopico
AGA. Álvarez García
A. Álvarez García
JTJavier Tarrío-Saavedra
Javier Tarrío-Saavedra
AMAntonio Meneses
Antonio Meneses
SFSalvador Naya Fernández
Salvador Naya Fernández

22 March 2023 in Heliyon
Verified
Journal Article
Open access
FRFrancisco J. Rodríguez-Dopico
Francisco J. Rodríguez-Dopico
RCR.J.C. Carbas
R.J.C. Carbas
CBCatarina Borges
Catarina Borges
JTJ. Tarrío-Saavedra
J. Tarrío-Saavedra
LSL.F.M. da Silva
L.F.M. da Silva
AGA.áLvarez García
A.áLvarez García
Although the shipbuilding industry is constantly demanding new advanced joining solutions, adhesive technology is not as developed in the marine as compared to other industries. The main reason is the lack of specific knowledge that guarantees the durability of the bonded joints in optimal conditions during the life cycle of a ship. This work simulates in the laboratory a marine-like environment by immersing an adhesive in seawater and subjecting it to constant loading. The objective is to characterize the seawater absorption behavior and its consequences on the mechanical, thermal, and chemical properties of the adhesive after this aging process. Seawater ingress was determined through gravimetric tests at several load conditions of the tensile strength of the adhesive. Besides, absorption process was studied using Fick's Law, determining the diffusion coefficients. The thermal behavior was monitored with differential scanning calorimetry (DSC) and the chemical degradation was analyzed using Fourier transform infrared spectroscopy (FTIR). Also, the mechanical properties were determined by tensile tests. The surface of the adhesive (dried) was studied by Scanning Electron Microscopy (SEM) technique and the porosity was measured by physisorption with a high-performance adsorption analyzer. A numerical simulation was developed using Darcy's Law combined with continuity equation. The results show that application of loads and immersion in seawater until full saturation of seawater improve the mechanical properties of the adhesive, but it affects negatively to the glass transition temperature. This should be considered when designing adhesive bonding joints on ships.

2 December 2024 in Oceans
Verified
Journal Article
Open access
PDF file
FRFrancisco J. Rodríguez-Dopico
Francisco J. Rodríguez-Dopico
AGAna Álvarez García
Ana Álvarez García
JTJavier Tarrío-Saavedra
Javier Tarrío-Saavedra
The shipping industry faces the challenge of expanding its capabilities and mitigating its environmental impact. The utilization of adhesive bonding techniques has the potential to facilitate the construction of lighter ships with a reduced carbon footprint. In this work, a complete methodology has been established to study the properties of an adhesive bond between naval steel and the behavior of the bulk adhesive when introduced into seawater. Thermogravimetric analysis (TGA) has been used to determine the thermal properties. Single-lap-joint and tensile tests have been performed showing the negative influence of temperature on the mechanical properties. Seawater absorption has been studied by gravimetric tests. Differential scanning calorimetry (DSC), Fourier transform infrared spectroscopy (FTIR), and mechanical bulk tests have been carried out before and after aging. The water absorption is Fickian, and when a constant load is applied, the absorption occurs faster and in greater quantity, decreasing the stiffness and strength. An increase in the glass transition temperature was observed in the absence of a load, with no discernible change upon the application of load condition. Also, aged specimens with constant load exhibited a reduction in water content. These phenomena may be attributed to several diffusion processes.

29 June 2024
Verified
Book Chapter
Closed access
PDF file
DSDaniel A. Souto-Silvar
Daniel A. Souto-Silvar
AÁA. Álvarez-García
A. Álvarez-García
FRFrancisco J. Rodríguez-Dopico
Francisco J. Rodríguez-Dopico
MTMaria Gonzalez Taboada
Maria Gonzalez Taboada


14 April 2023
Verified
Book Chapter
Closed access
PDF file
FRFrancisco J. Rodríguez-Dopico
Francisco J. Rodríguez-Dopico
BSB. Sánchez Silva
B. Sánchez Silva
AGA. Álvarez García
A. Álvarez García
JLJ. López-Beceiro
J. López-Beceiro
RAR. Artiaga
R. Artiaga
Adhesives play an important role in the reduction of weight on the ship. Thus, this work aims to achieve a better comprehension of the curing process and the viscoelastic properties of structural adhesives in order to choose the best option for naval steel bonding. Thanks to our use rheology and thermal characterization techniques, key information not provided by manufacturers was obtained. TGA was used to analyse specifically the thermal stability and filler content of the cured adhesives. Glass transition temperature and degree of curing at different temperatures were determined with DSC. Moreover, applying rheological techniques, the information of the thermal transformations is complemented from a viscoelastic point of view, determining the gelation time, the shrinkage along the curing process, and identification of the viscoelastic linear region.