Pilar Castejón

Ms. Pilar Castejón

orcid

Research Focus & Metrics

Academic Career Length

10Years (2017-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
29 December 2017 in Polymers
Verified
Journal Article
Open access
PDF file
PCPilar Castejón
Pilar Castejón
KHKian Habibi
Kian Habibi
ASAmir Saffar
Amir Saffar
AAAbdellah Ajji
Abdellah Ajji
AMAntonio B. Martínez
Antonio B. Martínez
DADavid Arencón
David Arencón
Several commercial grades of homo-polymer and its blends were selected to prepare microporous membranes through melt extrusion-annealing-uniaxial stretching technique (MEAUS). Branched or very fluid polypropylene was employed to modify the polymeric composition. In some blends, micro-sized calcium carbonate was added. We analysed the influence of sample composition, extrusion draw ratio, and we performed a deep study concerning the uniaxial strain rate, using in some cases extreme strain rates and strain extents. The crystalline features were studied by Differential Scanning Calorimetry (DSC), and the morphology of porous structure was analyzed through Scanning Electron Microscopy (SEM). Thermal stability and thermomechanical performance was measured by thermogravimetric analysis (TGA) and dynamic-mechanical-thermal (DTMA) study. A close relationship was found between crystalline characteristics, porous morphology and the trends registered for permeability.

19 January 2021 in Polymers
Verified
Journal Article
Open access
PDF file
PCPilar Castejón
Pilar Castejón
Marcelo AntunesMarcelo Antunes
Marcelo Antunes
DADavid Arencón
David Arencón
This work is made to ascertain the effects of mineral fillers, namely calcium carbonate and talc, on the morphology and properties of multilayer polypropylene (PP)/high-density polyethylene (HDPE) porous membranes. Multilayer membranes were prepared using the three-stage Melt-Extrusion, Annealing and Uniaxial Stretching (MEAUS) process. The orientation of PP’s crystalline phase was affected by both the flow-induced crystallization and the heterogeneous nucleation promoted by the fillers. A synergistic effect was observed in the filled samples due to the generation of pores after the stretching-induced lamellae separation and the debonding of mineral fillers from the polymeric matrix. The fillers increased the porous surface, leading to an increase of permeance to air, being this effect more marked at higher filler contents. Talc showed a higher efficiency to create porous surfaces when compared to calcium carbonate. The thermal stability of the membranes increased with filler addition, as well as their stiffness and strength.

2 August 2018 in Polymers
Verified
Journal Article
Open access
PDF file
PCPilar Castejón
Pilar Castejón
DADavid Arencón
David Arencón
Marcelo AntunesMarcelo Antunes
Marcelo Antunes
Vera RealinhoVera Realinho
Vera Realinho
José Ignacio VelascoJosé Ignacio Velasco
José Ignacio Velasco
AMAntonio B. Martínez
Antonio B. Martínez
In this study, block and random copolymers of polypropylene–ethylene are selected to prepare porous membranes through the melt extrusion-annealing-uniaxial stretching technique (MEAUS), at a constant draw ratio. In some cases, these copolymers were blended with a homopolymer grade. The variation of temperature in the stages of extrusion, annealing and uniaxial strain was analysed. Several characterisation techniques were employed to study this influence. The crystalline orientation was analysed by polarised infrared spectroscopy (FT-IR), and crystalline features were studied by differential scanning calorimetry (DSC). The thermal stability of the membranes was checked by thermogravimetric analysis (TGA). Tensile tests were performed to ascertain the stiffness and ductility of the produced samples. The results were correlated with the porous morphology, global porosity, and permeability to air. A close relationship was found between crystalline characteristics, porous morphology and the trends registered. An improved pore distribution along the membrane surface was found when copolymers were employed.

1 October 2017 in Polymer Testing
Verified
Journal Article
Open access
NLN. León
N. León
AMA.B. Martínez
A.B. Martínez
PCPilar Castejón
Pilar Castejón
DAD. Arencón
D. Arencón
PMP.P. Martínez
P.P. Martínez