RENATO CHAVES SOUZA

Dr. RENATO CHAVES SOUZA

orcid

Research Focus & Metrics

Academic Career Length

26Years (2001-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 January 2005 in Surface and Coatings Technology
Verified
Journal Article
Closed access
HVH.J.C. Voorwald
H.J.C. Voorwald
RSRENATO CHAVES SOUZA
RENATO CHAVES SOUZA
WPW.L. Pigatin
W.L. Pigatin
OCOdila Cioffi
Odila Cioffi

1 April 2001 in Surface and Coatings Technology
Verified
Journal Article
Closed access
MNMarcelino P Nascimento
Marcelino P Nascimento
RSRENATO CHAVES SOUZA
RENATO CHAVES SOUZA
IMIvancy M Miguel
Ivancy M Miguel
WPWalter L Pigatin
Walter L Pigatin
HVHerman J.C Voorwald
Herman J.C Voorwald

1 November 2008 in Surface and Coatings Technology
Verified
Journal Article
Closed access
RSRENATO CHAVES SOUZA
RENATO CHAVES SOUZA
HVH.J.C. Voorwald
H.J.C. Voorwald
OCOdila Cioffi
Odila Cioffi

1 September 2021 in Journal of Materials Research and Technology
Verified
Journal Article
Open access
CHC.S. Hattori
C.S. Hattori
GAGisele Fabiane Costa Almeida
Gisele Fabiane Costa Almeida
RGRodolfo Luiz Prazeres Gonçalves
Rodolfo Luiz Prazeres Gonçalves
RSR.G. Santos
R.G. Santos
RSRENATO CHAVES SOUZA
RENATO CHAVES SOUZA
ACAntonio augusto Couto
Antonio augusto Couto

1 March 2008 in Materials Research
Verified
Journal Article
Open access
PDF file
RSRENATO CHAVES SOUZA
RENATO CHAVES SOUZA
CSClaudinei dos Santos
Claudinei dos Santos
MBMiguel Justino Ribeiro Barboza
Miguel Justino Ribeiro Barboza
CBCarlos Antonio Reis Pereira Baptista
Carlos Antonio Reis Pereira Baptista
KSKurt Strecker
Kurt Strecker
CECarlos Nelson Elias
Carlos Nelson Elias
In this work, the static mechanical properties and cyclic fatigue life of 3 mol. (%) Y2O3-stabilized tetragonal zirconia polycrystalline (3Y-TZP) ceramics were investigated. Pre-sintered samples were sintered in air at 1600 °C for 120 minutes, and characterized by X ray diffraction and scanning electronic microscopy. Hardness and fracture toughness were determined by Vicker's indentation method, and Modulus of Rupture was determined by four-point bending testing. Fully dense sintered samples, near to 100% of theoretical density, presented hardness, fracture toughness and bending strength of 13.5 GPa, 8.2 MPa.m½ and 880 MPa, respectively. The cyclic fatigue tests were also realized using four-point bending testing, within a frequency of 25 Hz and stress ratio R of 0.1. The increasing of load stress lead to decreasing of the number of cycles and the run-out specimens number. The tetragonal-monoclinic (t-m) ZrO2-transformation observed by X ray diffraction contributes to the increasing of the fatigue life. The 3Y-TZP samples clearly presents a range of loading conditions where cyclic fatigue can be detected

1 January 2011 in Procedia Engineering
Verified
Journal Article
Open access
LML.P. Maduro
L.P. Maduro
CBC.A.R.P. Baptista
C.A.R.P. Baptista
MTM.A.S. Torres
M.A.S. Torres
RSRENATO CHAVES SOUZA
RENATO CHAVES SOUZA
The aluminum alloy 2524 (Al-Cu-Mg) was developed during the 90s mainly to be employed in aircraft fuselage panels, replacing the standard Al 2024. In the present analysis the fatigue crack growth (FCG) behavior of 2524-T3 was investigated, regarding the influence of three parameters: load ratio, pre strain and crack plane orientation of the material. The pre strain of aluminum alloys is usually performed in order to obtain a more homogeneous precipitates distribution, accompanied by an increase in the yield strength. In this work, it was evaluated the resistance of Al 2524-T3 sheet samples to the fatigue crack growth, having L-T and T-L crack orientations. FCG tests were performed under constant amplitude loading at three distinct positive load ratios. The three material conditions were tested: “as received”(AR), pre strained longitudinally (SL) and transversally (ST) in relation to rolling direction. In order to describe FCG behavior, two-parameter kinetic equations were compared: a Paris-type potential model and a new exponential equation introduced in a previous work conducted by our research group. It was observed that the exponential model, which takes into account the deviations from linearity presented by da/dN versus ΔK data, describes more adequately the FCG behavior of Al 224-T3 in relation to load ratio, pre strain effects and crack plane orientation