Alexander Sergeevich Antonov

Dr. Alexander Sergeevich Antonov

orcid

Research Focus & Metrics

Academic Career Length

5Years (2022-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
16 November 2024 in Materials
Verified
Journal Article
Open access
PDF file
HLHui Liu
Hui Liu
Gaoshen CaiGaoshen Cai
Gaoshen Cai
KPKai Peng
Kai Peng
JHJin Haozhe
Jin Haozhe
AAAlexander Sergeevich Antonov
Alexander Sergeevich Antonov
In this study, the size of molten pool and the porosity of parts under different processing parameters are studied using numerical simulation. According to the results, the appropriate processing parameters were selected to simulate the temperature and residual stress distribution during the forming process of body-centered cube (BCC), face-centered cube (FCC) and rhombic dodecahedron (Dode) lattice structures. In addition, three lattice structures were fabricated via selective laser melting (SLM) technology, and quasi-static compression experiments were carried out to study their mechanical properties. The results show that the high temperature parts of the three structures are all under the node and their adjacent pillars, and the closer to the nodes, the higher the temperature. The residual stress of the Dode structure is the highest, reaching 1218.2 MPa. It is also found that the residual stress in the Z direction is the largest, which plays a dominant role in the forming process. Through compression experiments, it is found that diagonal shear failure occurs in all three lattice structures, and Dode shows the best compression performance.

30 June 2026 in Вестник транспорта - Transport xabarnomasi
Verified
Journal Article
Closed access
AAAlexander Sergeevich Antonov
Alexander Sergeevich Antonov
ВСВ. Струк
В. Струк
МРМ. Рахматов
М. Рахматов
АРА. Рискулов
А. Рискулов
ХНХ. Нурметов
Х. Нурметов
В статье с применением методов численного моделирования и аналитических подходов проведен анализ влияния межфазного граничного слоя на эффективную теплопроводность гетерогенных систем «полимерная матрица – дисперсный наполнитель». Предложена и апробирована методика количественной оценки толщины теплового межфазного слоя на основе сопоставления экспериментальных данных и результатов конечно-разностного моделирования трёхмерного стационарного уравнения теплопроводности. Исследовано влияние размерного фактора частиц наполнителя на их собственную теплопроводность и результирующие теплофизические характеристики композита. Установлено, что при переходе в нанодиапазон доминирующую роль в ограничении теплопереноса играют межфазное термическое сопротивление Капицы и снижение теплопроводности материала частиц вследствие фононного рассеяния на границах.

10 July 2025 in Proceedings of the National Academy of Sciences of Belarus. Physical-technical series
Verified
Journal Article
Open access
PDF file
AAAlexander Sergeevich Antonov
Alexander Sergeevich Antonov
NPN. R. Prokopchuk
N. R. Prokopchuk
PKP. V. Klochko
P. V. Klochko
DND. V. Nakhvat
D. V. Nakhvat
Physico-chemical, structural and engineering prerequisites of modeling and optimization of tribological coatings based on polyamides in friction units of automobile and special units are considered. The analysis of the stress-strain state of the elements of the cardan transmission, carried out in CAE-systems Pro/ENGINEER Mechanica and LS-DYNA, allowed establishing the optimal thickness of tribological coating with minimum stresses. Composite materials based on commercially available polyamide PA-6 and adhesive sublayer for formation of tribological coatings on parts of the cardan shaft of trucks and special equipment are developed. It is proposed to introduce a polyamide resin based on aminoamides of resin acids of rosin, which has high compatibility with the polyamide matrix, provides plasticizing effect and uniform distribution of dispersed particles of modifier over the composite volume. When polyamide resin is used as an adhesive sublayer on the surfaces of the cardan transmission elements, increased interaction at the boundary “coating – sublayer” is provided. The developed composite coatings and adhesive sublayers, optimized by design solutions, have been tested in the cardan shafts produced by Belkard OJSC as a full-fledged alternative to imported analogues.

1 January 2022 in All the materials. Encyclopedic Reference Book
Verified
Journal Article
Closed access
MLMolder Llc
Molder Llc
SAS.V. Avdeychik
S.V. Avdeychik
EKE.T. Krut'Ko
E.T. Krut'Ko
BUBelarusian State Technological University
Belarusian State Technological University
AAAlexander Sergeevich Antonov
Alexander Sergeevich Antonov
ALA.N. Lesun
A.N. Lesun
Structural and technological aspects of obtaining composite materials based on polytetrafluoroethylene are considered. It is shown that due to the manifestation of the inertness of the components in the processes of interfacial interaction with an increase in the degree of filling, within the framework of the traditional technological paradigm, a structural paradox is realized. This paradox consists in a proportional decrease in the tensile strength parameter of fluorocomposites with an increase in their degree of filling. Based on the concept of energy and technological compliance of components, technological principles for eliminating the negative impact of the structural paradox by controlling the structure of fluorine composites at various levels of organization: molecular, supramolecular, phase and interfacial are proposed. Efficient methods have been developed for manufacturing products from highly filled fluorine composites containing 25–35% (wt.) carbon fiber and having parameters of stress-strain characteristics that are 1.5–2.0 times higher than the parameters of the analogues "Flubon", "Fluvis".