GUILLERMO Alzate-Espinosa

Prof. GUILLERMO Alzate-Espinosa

orcid

Research Focus & Metrics

Academic Career Length

13Years (2014-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 April 2017 in Journal of Petroleum Science and Engineering
Verified
Journal Article
Closed access
JUJ.A. Uribe-Patiño
J.A. Uribe-Patiño
GAGUILLERMO Alzate-Espinosa
GUILLERMO Alzate-Espinosa
AAALEJANDRA ARBELAEZ-LONDOÑO
ALEJANDRA ARBELAEZ-LONDOÑO

24 September 2014
Verified
Conference Paper
Closed access
PDF file
EAE. F Araujo
E. F Araujo
GAGUILLERMO Alzate-Espinosa
GUILLERMO Alzate-Espinosa
AAAlejandra Arbelaez-Londono
Alejandra Arbelaez-Londono
SCS. Peña Clavijo
S. Peña Clavijo
ARA. Cardona Ramirez
A. Cardona Ramirez
EGEdson Felipe Araujo Guerrero
Edson Felipe Araujo Guerrero
Sand production treatment, control and mitigation generate high costs for the petroleum industry. Therefore, this is considered a critical problem and requires a continuous monitoring and special management. A sand production study is fundamental in field development and will help to eliminate or mitigate the related problems. This way, an analytical geomechanical sand production model is proposed to design the best field sand free production plan and to select the type of sand control measures and sand management techniques. The model needs as input data, the reservoir characteristicsn and a mechanical earth model derived from well logs that includes the stress state regime. It also requires the well direction, azimuth and completion information in order to evaluate the well characteristics. In this model an onset sand production condition is calculated looking for the borehole pressure that makes the maximum effective tangential compressive stress equal or higher than the rock strength (failure criteria), which is usually known as critical borehole pressure (CBHP). The results are presented on two kinds of graphs: the CBHP versus depth graph that allows determining the sand production free interval and the CBHP versus reservoir pressure graph that helps to design different well production plans for optimizing the recovered volume avoiding sand production. Results must be calibrated and verified with data field to simulate the real reservoir behavior. Briefly, for a specific well path it is possible to propose the operating CBHP as a function of the reservoir depletion and well completion (open or cased hole), also for a new well, it is possible to design the best well direction and the completion type, in addition to the operating CBHP to minimize sand production.

18 April 2018 in Geotechnical and Geological Engineering
Verified
Journal Article
Closed access
PDF file
CMC. B. Morales-Monsalve
C. B. Morales-Monsalve
ILI. F. Lara-Restrepo
I. F. Lara-Restrepo
EAE. F. Araujo-Guerrero
E. F. Araujo-Guerrero
GAGUILLERMO Alzate-Espinosa
GUILLERMO Alzate-Espinosa
AAALEJANDRA ARBELAEZ-LONDOÑO
ALEJANDRA ARBELAEZ-LONDOÑO
ANA. Naranjo-Agudelo
A. Naranjo-Agudelo

26 October 2021 in Energies
Verified
Journal Article
Open access
PDF file
JAJuan Alejandro Arias-Buitrago
Juan Alejandro Arias-Buitrago
GAGUILLERMO Alzate-Espinosa
GUILLERMO Alzate-Espinosa
AAALEJANDRA ARBELAEZ-LONDOÑO
ALEJANDRA ARBELAEZ-LONDOÑO
GZGonzalo Zambrano-Narvaez
Gonzalo Zambrano-Narvaez
Richard ChalaturnykRichard Chalaturnyk
Richard Chalaturnyk
Hydrocarbon reservoirs can be subjected to temperature changes due to different processes during production. Heat injection has become an advantageous method to produce heavy oils in Canada and Venezuela because it increases oil recovery. The heat reduces oil viscosity and oil flows easily. Colombia has significant heavy oil reserves in unconsolidated silty sandstones. It is important to understand the mechanical behavior of these reservoirs in thermal recovery conditions (temperature and effective stress). The reconstituted samples from a Colombian heavy oil outcrop were evaluated using a high-temperature and high-pressure triaxial cell. Twelve isotropically consolidated drained triaxial tests were conducted at three different effective stresses (0.4, 4.0, and 8.2 MPa) and a temperature range from 50 to 230 °C to represent the initial and thermal recovery conditions, and obtain parameters, such as Young’s and Bulk moduli, internal friction angle, and cohesion. The samples at higher confining stress (4.0 and 8.2 MPa) were under contraction, while samples at lower confining stress (0.4 MPa) were under dilation. The stiffness increased as the confining stress increased and decreased as temperature increased, and the strength properties significantly decreased as temperature increased. Finally, the Colombian samples exhibited low friction angles when compared to clean sandstones as Canadian sands.

1 September 2018 in Journal of Petroleum Science and Engineering
Verified
Journal Article
Closed access
DCD.F. Cartagena-Pérez
D.F. Cartagena-Pérez
JAJ.A. Arias-Buitrago
J.A. Arias-Buitrago
GAGUILLERMO Alzate-Espinosa
GUILLERMO Alzate-Espinosa
AAALEJANDRA ARBELAEZ-LONDOÑO
ALEJANDRA ARBELAEZ-LONDOÑO
CMC.B. Morales–Monsalve
C.B. Morales–Monsalve
ANA. Naranjo-Agudelo
A. Naranjo-Agudelo

21 May 2014
Verified
Conference Paper
Closed access
GAGUILLERMO Alzate-Espinosa
GUILLERMO Alzate-Espinosa
MAMastan Arbeláez-Londoño
Mastan Arbeláez-Londoño
AAA. Naranjo Agudelo
A. Naranjo Agudelo
RRR. D. Romero
R. D. Romero
MBM. A. Bolaños
M. A. Bolaños
CPC. A. Peláez
C. A. Peláez
Well logs acquired directly in field have turned out to be one of the most key engineering elements to evaluate hydrocarbon formations. Nevertheless, the lack of information, some technical troubles related to the unfolding of tools, the operational states of the well and many other reasons may sharply limit the carrying out of an optimal formation characterization methodology along the entire productive or injective lifespan of a reservoir. Nowadays, artificial neural networks (ANN) are one of the strongest tools to supply such missing information in order to generate synthetic logs. In this paper, we explain the putting into practice of an ANN methodology with the aim of provide useful input information in geomechanical modeling for the hydraulic fracturing simulator GIGAFRAC. More explicitly, the purpose of the schemes presented here is to provide transit-time curves for primary or compressional waves (DtP) and secondary or shear waves (DtS), based on full information measurements of Gamma Ray, Neutron-Porosity, Density, DtP and DtS logs; for some wells in the Cupiagua field located in Colombian Foothills, which break through some geologic formations such as Mirador, Barco, Guadalupe, and Los Cuevos. A noteworthy amount of considerations were taken into account to ensure the success of the ANN estimation phases. A strong focus is done regarding to filtration and quality control of the input information to the network, relating to the control mechanism of outliers, as well as the splitting-up of logs in zones by using a geological criteria and spreading of data information in computationally convenient vectorial and matricial arrangements. Finally, good adjustments were obtained throughout the validation phases and they all were considered as successful outcomes, together with training phase and subsequent use of the same for estimating DtP and DtS curves.