Disease diagnosis through biological fluids, particularly exhaled breath analysis, has gained increasing importance. Volatile organic compounds (VOCs) present in exhaled breath offer diagnostic potential as they reflect altered and disease-specific metabolic pathways. While gas chromatography–mass spectrometry (GC–MS) has been traditionally used for VOCs detection, electronic noses have emerged as a promising alternative for disease screening. Metal oxide semiconductor (MOS) sensors play an essential role in these devices due to their simplicity and cost-effectiveness. However, their limited specificity and sensitivity pose challenges for accurate diagnosis at lower VOCs concentrations, typical of exhaled breath. To address specificity and sensitivity issues, temperature modulation (TM) has been proposed in this paper, introducing a custom-developed electronic nose based on multiple and heterogeneous gas sensors located within an analysis chamber. Four different TM patterns (i.e., square, sine, triangular, and a combination of square and triangular) were applied to the gas sensors to test their response to three different analytes at three distinct concentrations. Data were analyzed by extracting meaningful features from the sensor raw data, and dimensionality reduction using principal component analysis (PCA) was performed. The results demonstrated distinct clusters for each experimental condition, indicating successful discrimination of analytes and concentrations. In addition, an analysis of which set of sensors and modulation pattern yielded the best results was performed. In particular, the most promising TM pattern proved to be the square and triangular combination, with optimal discrimination accuracy between both concentrations and analytes. One specific sensor, namely, TGS2600 from Figaro USA, Inc., provided the best performance. While preliminary results highlighted the potential of TM to improve the sensitivity of gas sensors in electronic nose devices, paving the way for further advancements in the field of exhaled breath analysis.
Graphene oxide and its magnetic nanoparticle-based composites are a well-known tool to remove heavy metals from wastewater. Unfortunately, one of the major issues in handling such small particles consists of their difficult removal from treated wastewater (even when their magnetic properties are exploited), due to their very small diameter. One possible way to overcome this problem is to embed them in a macroscopic biopolymer matrix, such as alginate or chitosan beads. In this way, the adsorbent becomes easier to handle and can be used to build, for example, a packed column, as in a traditional industrial adsorber. In this work, the removal performances of two different embedded magnetic nanocomposite adsorbents (MNAs) are discussed. The first type of MNA is based on ferrite magnetic nanoparticles (MNPs) generated by coprecipitation using iron(II/III) salts and ammonium hydroxide, while the second is based on a 2D material composed of MNP-decorated graphene oxide. Both MNAs were embedded in cross-linked alginate beads and used to treat artificial water contaminated with chromium(III), nickel(II), and copper(II) in different concentrations. The yield of removal and differences between MNAs and non-embedded magnetic nanomaterials are also discussed. From the results, it was found that the time to reach the adsorption equilibrium is higher when compared to that of the nanomaterials only, due to the lower surface/volume ratio of the beads, but the adsorption capacity is higher, due to the additional interaction with alginate.
For a long time, the leather industry has considered the chromium tanning process to be the easiest and fastest way to treat raw hides and transform them into valuable products. In the last few decades, increasing attention has been paid to the potential oxidation of the trivalent chromium in tanned leather. This happens for many reasons, such as the quality of the tanning agent or the adoption of good manufacturing practices. Anyway, the main problem, which is difficult to solve, is the sensibility of the free residual chromium tanned leather, which is high enough for possible harmful activity. Given this scenario, this work proposes a solution to decrease hexavalent chromium formation by using antioxidants during the leather tanning process. In this regard, a screening work was started, to find the worst-case scenario for trivalent chromium oxidation. To do this, commercial tanning products were employed, especially fatliquoring agents, which, in some cases, are the main source that could easily react with ROS (Reactive Oxygen Species) to drive chromium oxidation. After the determination of conditions, different groups of common antioxidants were tested to analyse the antioxidation performances and their possible use in the chromium-based tanning process. The results underline the efficient action of the antioxidants studied, paving the way for some interesting perspectives to limit the drawbacks of chromium tanned leather.
Finished tanned leather is usually covered by a thin polymeric layer. This layer has the scope to change the morphological aspect of the last leather layer as well as improve the impermeabilization properties. Often, the finished product is refused by the final client, and tanneries must restore significant quantities of materials. Therefore, it is very important to remove this finished polymeric layer, recover the underneath tanned leather, and predispose it to a new finishing. The bonding between the polymeric film and leather is so strong that, today, only a blade shaving process can perform this separation at the expense of also removing a layer of tanned leather and consequently reducing the leather thickness. Here, a novel separation method was developed based on the significant difference in the dilation properties between the tanned hide and the polymeric film at low temperatures. The use of cryogenic fluids, in particular the direct application of liquid nitrogen, can freeze the polymeric layer below the glass transition temperature, inducing brittle behavior. The result is an easy separation without any alteration of the tanned leather layer; for a demonstration of that, some techniques were used, such as FTIR, SEM, Tensile strength evaluation, DSC, and TGA. By this last analysis, it is possible to check how a decrease of weight to 90% happened for the polymeric layer at about 400 °C against the complete blank at about 600 °C. A similar great distance of results exists in the case of tensile strength, where an average value of 34.5% is the deformation stress for blank samples, against 34.8% for processed samples. Thus, the process here developed allows the reuse of the tanned leather towards a new life in respect of the principles of the circular economy.
Finished tanned leather are usually covered by a thin polymeric layer. This layer has the scope to change the morphological aspect of the last leather layer, as well as to improve the impermeabilization properties. Often, the finished product is refused by the final client and tanneries must restore significant quantity of materials. Therefore, it is very important to remove this finished polymeric layer, to recover the underneath tanned leather and to predispose it to a new finishing. The bonding between the polymeric film and leather is so strong that, today, only a blade shaving process can perform this separation at the expenses of also removing a layer of tanned leather and consequently reduce the leather thickness. Here, a novel separation method was developed, based on the significant difference in the dilation properties between the tanned hide and the polymeric film at low temperature. The use of cryogenic fluids, in particular the direct application of liquid nitrogen, can freeze the polymeric layer under the glass transition temperature and then inducing a brittle behaviour. The result is an easy separation without any alteration of the tanned leather layer. Thus, the process here developed, allows the reuse of the tanned leather towards a new life in the respect of the circular economy principles.