A nanocatalyst comprising ultra-small palladium nanoparticles supported on nanodiamonds (ultra-small Pd/rNDs) was fabricated via a reduction of palladium (II) salt on oxidized nanodiamond. The prepared catalyst was characterized using XRD, XPS, ICP-MS, AAS, and TEM/HRTEM techniques, including STEM-EDS chemical mapping, which revealed that the modified material is a combination of reduced nanodiamond decorated with palladium nanoparticles. The as-prepared and well-characterized ultra-small Pd supported on rNDs displayed superb catalytic activity for Suzuki–Miyaura cross-coupling reactions at low temperature without any toxic solvents, to obtain the respective products in good-to-excellent yields (75–98%). The catalyst was easily separated from the reaction solution and was reused four times without loss of catalytic activity or chemical stability.

The growing concentration of CO₂ in the atmosphere is a serious problem, and efforts to counter this issue are thus highly important. One of the possible approaches to solving this problem is the conversion of waste CO₂ into products with added economic value. Methanol is one of these products with vast potential usage. In this study, indium oxide prepared by a simple precipitation method and modified by nanoparticles of metals from the iron triad were tested as possible catalysts to produce methanol by the method of CO₂ hydrogenation. The prepared catalysts demonstrated a strong dependence of their catalytic activity on used metal. The best selectivity for the production of CH₃OH was observed for the Fe/In₂O₃ catalyst at the value of 54.7% at 300 °C. However, due to the higher value of CO₂ conversion, the highest CH₃OH formation rate was observed at a value of 11.3 mmol/(h*g) at 300 °C for a composite of Ni/In₂O₃.

The hematite phase decorated with iron-doped cerium oxide nanoparticles (F@FC) was precipitated from cerium and iron oxalate intermediate products. The photocatalytic composite of graphitic carbon nitride (gCN) and F@FC was prepared by a simple method involving mixing the two components, followed by thermal treatment at 400 °C. According to electron microscopy, F@FC is composed of a submicron iron oxide (hematite) phase decorated with iron-doped cerium oxide nanoparticles deposited on gCN substrate. A hierarchically structured composite was observed instead of a simple mechanical mixture of α-Fe₂O₃, Fe-CeO₂, and gCN. To observe two types of degradation activity, photocatalytic and Photo-Fenton degradation activity, Rhodamine B (RhB) was applied as the model water pollutant. The influence of the amount of photocatalyst, the RhB concentration, the presence of cations and anions, the pH, and the effect of e⁻, h⁺, •OH, and •O₂⁻ scavenging reactants were studied. The Photo-Fenton degradation exhibited high efficiency across the entire tested pH range, whereas photocatalytic degradation showed comparable activity only at acidic pH. The F@FC-gCN composite catalyst exhibited a high degree of recyclability. The degradation pathways of photocatalytic and Photo-Fenton reactions were suggested by HPLC-MS analysis of the reaction products. A notable finding of this study was the observation that the green-yellow, fluorescent intermediate Rhodamine 110 was formed during the photocatalytic degradation of RhB. However, the high reactivity of the generated •OH radicals during Photo-Fenton degradation has been demonstrated to inhibit the formation of intermediate Rhodamine 110.

The synthesis, in particular the industrial production, of pharmaceuticals requires a broad arsenal of synthetic reactions capable of selectively forming specific structural motifs and assembling smaller building blocks into complex molecules. The Chan–Evans–Lam cross-coupling reaction, which forms a bond between a N-nucleophile and an aryl group from a boronic acid, catalysed by copper salts, is a typical example of this synthetic route. Considering the toxicity of copper and the stringent regulatory limits for its residues in final pharmaceutical products, a heterogeneous catalytic approach offers a viable alternative for this transformation. In this work, we present a simply and reproducibly synthesized catalyst based on copper nanoparticles supported on reduced graphene oxide (Cu-rGO), with high efficiency in a model Chan–Lam reaction involving benzimidazole and aniline derivatives with substituted boronic acids.