Pavel Kovačócy

Dr. Pavel Kovačócy


Research Focus & Metrics

Academic Career Length

9Years (2018-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
2 January 2020 in Journal of Materials Engineering and Performance
Verified
Journal Article
Closed access
PDF file
PKPavel Kovačócy
Pavel Kovačócy
BŠBeáta Šimeková
Beáta Šimeková
IKIngrid Kovaříková
Ingrid Kovaříková
EHErika Hodulova
Erika Hodulova
MDMária Dománková
Mária Dománková
Peter JurčiPeter Jurči
Peter Jurči

17 October 2024 in Metals
Verified
Journal Article
Open access
PDF file
BŠBeáta Šimeková
Beáta Šimeková
MDMária Dománková
Mária Dománková
IKIngrid Kovaříková
Ingrid Kovaříková
PKPavel Kovačócy
Pavel Kovačócy
MMMaros Martinkovic
Maros Martinkovic
LCLuke Ciuła
Luke Ciuła
The influence of laser beam welding parameters (power, welding rate, focusing, head oscillation, shielding gas) on the microstructure, mechanical properties and corrosion resistance of the super-duplex stainless steel SAF 2507 was studied in this paper. The presented results clearly report the effects of welding parameter changes on the character of the steel’s microstructure. The presence of secondary phase M2N in weld metals has an important influence on their mechanical properties. Optimal mechanical properties, an acceptable ferrite/austenite ratio, and the minimum content of M2N nitride required in the weld metal were acquired in the case the following application: 1100 W power, welding speed of 10 mm/s, focusing of 4 mm, and pure nitrogen shielding gas (20 L/min).

17 December 2024 in Acta Polytechnica CTU Proceedings
Verified
Journal Article
Open access
PDF file
PKPavel Kovačócy
Pavel Kovačócy
MMMaroš Martinkovič
Maroš Martinkovič
BŠBeáta Šimeková
Beáta Šimeková
MHMartin Hnilica
Martin Hnilica
IKIngrid Kovaříková
Ingrid Kovaříková
MKMichal Krbaťa
Michal Krbaťa
Duplex stainless steels (DSS) are dual-phase alloys consisting of austenitic and ferritic phases in the microstructure. DSS provide an ideal compromise between mechanical properties and corrosion resistance. Welding of DSS leads to a change in the ferrite/austenite ratio in the microstructure and to degradation of the properties of the weld joints. Therefore, it is very important to control the microstructure of the weld joint directly during the welding process. An innovative method of laser welding applying a dual beam was used. By spreading the energy of the laser beam over two spots, additional heat is introduced into the weld, which ensures a slowdown in the cooling rate of the DSS and possibly ensures the desired ratio of ferrite and austenite in the microstructure. The influence of laser welding parameters and energy distribution of the dual beam on the fusion zone (FZ) geometry, resulting microstructure and mechanical properties of the weld joints was monitored. The tensile and shear strength was measured. The coefficient of proportionality between shear and tensile strength was calibrated to be as 1.38 ± 0.01.

10 September 2022
Verified
Book Chapter
Closed access
PDF file
MHMartin Hnilica
Martin Hnilica
EHErika Hodulova
Erika Hodulova
MSMiroslav Sahul
Miroslav Sahul
PKPavel Kovačócy
Pavel Kovačócy
BŠBeáta Šimeková
Beáta Šimeková
IKIngrid Kovaříková
Ingrid Kovaříková

10 September 2022
Verified
Book Chapter
Closed access
PDF file
IKIngrid Kovaříková
Ingrid Kovaříková
PKPavel Kovačócy
Pavel Kovačócy
MSMiroslav Sahul
Miroslav Sahul
BŠBeáta Šimeková
Beáta Šimeková
MMMaros Martinkovic
Maros Martinkovic
EHErika Hodulova
Erika Hodulova

1 June 2018 in Research Papers Faculty of Materials Science and Technology Slovak University of Technology
Verified
Journal Article
Open access
PDF file
JRJürgen Rigo
Jürgen Rigo
PKPavel Kovačócy
Pavel Kovačócy
An important point in Tribology is mechanical-dynamic testing of lubricants and materials under stress and the interpretation of the results obtained therefrom. Widely-used test methods are often applied to test the performance of lubricants e.g. test results determined by tribometers should be treated carefully when using marketable oils. A closer evaluation of these results is part of this research paper. Within this study, several marketable oils were used and experimentally investigated. These were a gear oil, two engine oils, one hydraulic oil, one metal working fluid and one forming oil. There were several distinct differences. On the one hand, the used oils differ significantly in terms of their performance in the individual test methods. This is not surprising but has a clear reason in the different compositions of the lubricants resulting from their respective application. By subjecting these oils to diverse test methods with different test equipment, the results can vary widely and result in completely dissimilar results from the tests. Thus, a metalworking oil appears excellently when determining the welding force in the four-ball apparatus. In the high frequency liear oscillation tester, on the other hand, barely usable results are generated. Thus, there are two contradictory statements that should be the same.